Beninca BOB21M, BOB30M, BOB30ME Gate Automation

Product Overview

The Beninca BOB series offers reliable automation solutions for swing gates. This manual provides comprehensive instructions for installation, operation, and maintenance of the BOB21M, BOB30M, and BOB30ME models.

Safety Precautions

General Warnings:

• This product is intended solely for the purpose described in this manual. Any other use is prohibited and may lead to product damage or personal injury.
• Installation and maintenance should only be performed by qualified personnel.
• Ensure the gate structure is suitable for automation.
• Keep packaging materials away from children.
• Do not allow children to play with the control devices or near the gate.
• Apply all necessary safety devices such as photocells and safety edges.
• Use only original Beninca accessories and spare parts.
• Comply with all relevant safety standards and directives.

Electrical Safety:

• Ensure the power supply is properly earthed.
• Disconnect power before performing any electrical work.
• All electrical installations must comply with current regulations.

Waste Disposal:

• Dispose of this product responsibly according to local regulations. Do not discard with household waste.

Technical Specifications

Installation

Preliminary Checks:

• Ensure the gate moves smoothly without resistance.
• Check that the gate remains in position when stopped.
• Verify hinges and wear parts are in good condition.
• Confirm gate structure is robust and leaves are rigid.
• Ensure leaves align perfectly when closed.
• Check that support pillars are suitable for motor mounting.
• A ground stop for closing is recommended.

Fitting the Automation:

1. Determine the correct height for the automation unit, ensuring it is centered and aligned with a sturdy cross piece.
2. Weld mounting plate P according to Figure 2 dimensions.
3. With the gate closing, weld bracket S according to Figure 2 dimensions to a suitable gate cross piece, ensuring the actuator is not at its end of travel.
4. Remove protective cover C by unscrewing screw F.
5. Fix the actuator to plate P using screw T, washer L, and nut D.
6. Secure the actuator to bracket S using screw V and washer R.
7. Use the pre-drilled holes (Figure 2A) for precise installation.
8. Adjustable fixing brackets (available on request) can facilitate installation in various conditions.

Mechanical Stopper Adjustment:

1. Unlock the automation using the release lever.
2. Move the gate leaf to the closed position.
3. Loosen screws V1, move the "Close" lock to contact pivot P, and tighten screws V1.
4. Move the gate leaf to the open position.
5. Loosen screws V2, move the "Open" lock to contact pivot P, and tighten screws V2.
6. Restore automatic operation.

Connections:

• Use the provided plate P for PG11 or PG13.5 cable glands.
• Ensure the unit is properly earthed using the GND terminal.

Electrical Connections

The required cables may vary depending on installed accessories. No connection cables are supplied.

Use appropriate cables for the connection type (e.g., H03VV-F for channeled installations, H07RN-F for outdoor installations).

Manual and Emergency Operation

In case of power failure or malfunction, follow these steps to operate the gate manually:

1. Open the protective door (Figure A*).
2. Insert and turn the personalized key C anti-clockwise (Figure B*).
3. Open the protective door of the release mechanism (Figure C).
4. Insert the special release key and turn it 90° (Figure D for right actuator, Figure E for left actuator).
5. The gate can now be opened or closed manually.
6. To restore automatic operation, return the release key to its original position.
7. Remove the release lever and close the protective door.

*Only for BOB30M / BOB30ME models.

Maintenance

• Periodically check the operation of the emergency manual release.
• Do not attempt any repairs yourself; contact a qualified technician.
• The operator is maintenance-free, but safety devices and other components should be checked periodically for wear.

Parts List

Declaration of Conformity

The product complies with the following EU directives:

• Directive 2014/30/UE (EMCD)
• Directive 2014/35/UE (LVD)
• Directive 2011/65/UE (RoHS)

For the full declaration and latest updates, please visit the Beninca website.