Aidapt Overbed Table

INTRODUCTION

Thank you for purchasing the Economy Overbed Table from Aidapt.

These instructions should be read carefully and left with the user of the product for future reference. Please see our website user manual if you require a larger font.

Please ensure this equipment is installed by a competent person.

• VG832B – Overbed Table with Castors Max Weight Load 15kg
• VG866B – Overbed Table without Castors Max Weight Load 15kg

DO NOT exceed the weight limit stated – doing so could put you at risk.

BEFORE USE

• Carefully remove all packaging. Avoid using any knives or other sharp instruments as this may damage the surface of the product.
• Check the product for any visible damage. If you see any damage or suspect a fault, do not use your product, but contact your supplier for support.

INTENDED USE

The Aidapt Economy Overbed Table is a convenient table for use around the home. This height-adjustable table has a hardwood upstand and the top can also be set to different angles from flat to 45° approximately, as required.

FEATURES

• Ideal for those confined to bed
• Ideal for use around the home
• Height adjustable and angle adjustable to suit most users
• It features a veneer style table top with Book Stoppers
• Maximum load 15kg

PARTS

Diagram (fig. 1) shows the components of the Aidapt Overbed Table. These include a U-shaped base frame with wheels (castors), a table top, an H-shaped frame, thumb wheels, C-shaped brackets, L-shaped tubes, screws, E-clips, and a spanner.

• A. U Base Frame x 1
• B. Table Top x 1
• C. H Frame x 1
• D. Castors x 4 (VG832B ONLY)
• E. Thumb Wheel x 2
• F. C Shaped Brackets x 4
• G. L Tube x 2
• H. Screws x 8
• I. E-Clips x 2
• J. Spanner x 1

ASSEMBLY INSTRUCTIONS

Please examine your product for any visible damage before using/installing. If you see any damage or suspect a fault, please do not use, but contact your supplier.

1. Carefully remove all packaging and ensure all loose fitments have been provided. (See fig. 1 for parts overview).

2. If you have purchased the VG832B (with castors) follow this step, otherwise move on to step 3. Locate the pre-punched castor holes on the base frame (as shown in fig. 2). Align the castor and screw in with the spanner (J) provided (see fig. 3). Ensure castors are fully tightened.

   Diagram Description (fig. 2): Illustrates the U-shaped base frame with four pre-punched holes where the castors are to be attached.

   Diagram Description (fig. 3): Depicts a castor being screwed into the base frame using the provided spanner.

3. Turn the U frame over so that the spigots are facing up. Lower the H frame onto the spigots of the U frame (see fig. 4). Ensure the black plastic collars on the H frame are at the top and the spigots on the H frame are facing outwards (see fig. 5).

   Diagram Description (fig. 4): Shows the H-frame being lowered onto the spigots of the inverted U-frame. Arrows indicate the direction of movement.

   Diagram Description (fig. 5): A close-up view showing the black plastic collars on the H-frame and the orientation of the spigots on the H-frame.

4. Align pre-punched holes in the bottom of the H frame with the pre-punched holes in the spigots of the U frame. Insert E-clips to lock in position, ensuring they click in place and are secure (see fig. 6 and 7).

   Diagram Description (fig. 6 & 7): Close-up views illustrating the insertion of E-clips into aligned holes to secure the H-frame to the U-frame spigots. The clips are shown clicking into place.

5. Place the L-shaped tube onto the underside of the table top, observing the following (VERY IMPORTANT):

   • The riveted end of the L-shaped tube MUST be placed onto the underside of the table top (see fig. 8).
   • The riveted end of the L-shaped tube MUST be placed between pre-drilled holes nearest to the edge of the table (approximately 10 cm from table edge) (see fig. 9 and 10).

   Diagram Description (fig. 8): A view of the underside of the table top, showing the placement of the riveted end of an L-shaped tube.

   Diagram Description (fig. 9): Diagram showing the correct placement of the riveted end of the L-shaped tube on the underside of the table top, between pre-drilled holes nearest to the edge, approximately 10 cm from the edge. A checkmark indicates correctness.

   Diagram Description (fig. 10): Diagram showing the incorrect placement of the riveted end of the L-shaped tube. An 'X' mark indicates incorrectness.

6. Attach the L-shaped tubes using four C-shaped brackets and eight screws (see fig. 11). Ensure that the two C-shaped brackets nearer the edge of the table are between the two rivets (see fig. 12). Do not overtighten as this may cause damage to the table.

   Diagram Description (fig. 11): Shows the L-shaped tubes being attached to the underside of the table top using C-shaped brackets and screws.

   Diagram Description (fig. 12): A close-up detail showing a C-shaped bracket positioned correctly between two rivets on the underside of the table top. An arrow indicates the correct placement.

7. Insert the free ends of the L-shaped tubes into the H-frame (see fig. 13). You may require assistance to align them correctly. Slowly lower the table top (see fig. 13). Ensure you lower both sides at the same time to prevent binding.

   Diagram Description (fig. 13): Illustrates the process of inserting the free ends of the L-shaped tubes into the H-frame and lowering the table top. Arrows show the downward movement and the alignment of the tubes.

8. Loosely attach two thumbwheels to the small spigots at the top of the H-frame (see fig. 14).

   Diagram Description (fig. 14): Shows the two thumbwheels being loosely attached to the small spigots at the top of the H-frame.

9. Raise or lower the table top to the desired height and tighten thumb wheels by turning clockwise to secure (see fig. 15). Ensure the height is the same on both sides; otherwise, the table will not be level and not safe for use.

   Diagram Description (fig. 15): Demonstrates tightening the thumbwheels clockwise to secure the table top at the desired height. Arrows indicate the clockwise rotation.

10. To adjust height, loosen thumb wheels anti-clockwise (see fig. 16) and repeat step 9.

    Diagram Description (fig. 16): Demonstrates loosening the thumbwheels anti-clockwise to adjust the height. Arrows indicate the anti-clockwise rotation.

OPERATION INSTRUCTIONS

• To adjust the height and/or angle of the table, first loosen the two short hand screws by turning them anticlockwise. Adjust the table to suit and secure by turning hand screws clockwise.
• The table is not load bearing and should not be used to support objects over 15kg (33lbs).
• Do not allow people to lean on the table.

WARNINGS

• The Overbed Table requires a risk assessment before use.
• The Overbed Table must be checked periodically to ensure it is securely in place, retighten as required.
• DO NOT overtighten the screws, otherwise this will cause damage to the table top.
• DO NOT EXCEED 15kg weight load.

CLEANING

All of the product components are manufactured from quality materials. However, it is very important that you only clean your Over Bed Table using a non-abrasive cleaner or mild detergent with a soft cloth. Avoid using lime scale remover. Abrasive cleaners or abrasive cleaning pads will seriously damage your product beyond repair.

If to be disinfected by heat (apart from the wooden table top), one of the following three temperatures and duration of exposure can be used:

• a. A temperature of 90°C for 1 minute
• b. A temperature of 85°C for 3 minutes
• c. A temperature of 80°C for 10 minutes

CARE, MAINTENANCE AND YOUR OBLIGATION

Please check the Over Bed Table periodically for any signs of damage and if in doubt contact your supplier.

TECHNICAL INFORMATION

IMPORTANT INFORMATION

The information given in this instruction booklet must not be taken as forming part of or establishing any contractual or other commitment by Aidapt Bathrooms Limited or its agents or its subsidiaries and no warranty or representation concerning the information is given.

Please exercise common sense and do not take any unnecessary risks when using this product; as the user you must accept liability for safety when using the product.

SERVICE WARRANTY

Aidapt Bathrooms Ltd guarantees the product free from defects in material and workmanship for a period of one year.

Should this product be operated under conditions other than those recommended, or any attempts made to service or modify the product, then the warranty is rendered void.

The product you buy may differ slightly from illustrations. This warranty is in addition to, and does not affect your statutory rights.

Our guarantee is administered by our retailers.

If your product arrives damaged, you must contact the retailer from whom you bought it. The retailers contact details will be on the invoice that arrived with the product, or on the email you received when you placed the order. Do not contact Aidapt Bathrooms Ltd, only your retailer can arrange a replacement or refund.

If your product fails within the guarantee period, please contact the retailer from whom you bought it.

If you have received your product and require technical help, please call our help desk on 01744 745 020.

A copy of the instructions leaflet can be downloaded from our website.

Contact Information

Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX

Telephone: +44 (0) 1744 745 020

Fax: +44 (0) 1744 745 001

Web: www.aidapt.com

Email: sales@aidapt.co.uk