VEVOR Vacuum Packing Machine User Manual

Introduction

This manual provides instructions for the VEVOR Vacuum Packing Machine, Model DZ600-2S-V1. It is important to read all instructions carefully before operating the machine. VEVOR reserves the right to interpret the user manual, and the product appearance is subject to the received item. Updates to technology or software may occur without prior notice.

General Safety Rules:

• Read and understand all assembly and operation instructions before use.
• Failure to follow safety rules may result in serious personal injury.
• The guarantee/warranty is void if damage occurs due to non-compliance with operating instructions. Liability for consequential damage is excluded.
• VEVOR assumes no liability for damage to property or personal injury caused by improper use or failure to observe safety instructions.
• Unauthorized conversion, modification, or disassembly is prohibited due to safety and approval reasons (CE).
• This product is not a toy and must be kept out of reach of children.
• Use only in dry, indoor locations. Risk of fatal electric shock if exposed to moisture.
• Do not expose the product or accessories to damp or extreme temperatures.
• Do not leave packing materials unattended, as they can be dangerous for children.
• Dropping, falling, pressure, or tensile forces can damage the product.
• Never position the device near combustible or easily inflammable materials.
• Ensure the object is placed in the center of the rotary table within the housing.

This machine uses plastic film or plastic aluminum film for vacuum packaging various items, including food, chemicals, electronic components, and precision instruments. Vacuum packaging helps prevent oxidation and mold, making it suitable for industries like tea, food, and medicine.

Important Safety Note: If you suspect unsafe operation, disconnect the device immediately and secure it against inadvertent operation. Safe operation is compromised if:

• The device shows visible signs of damage.
• The device no longer functions.
• The device has been stored under unfavorable conditions for a long time.
• The device has undergone heavy stress during transportation.

SAVE THESE INSTRUCTIONS

Model and Parameters

Structure Diagram

The machine consists of the following parts:

• 1. Vacuum cover
• 2. Handle
• 3. Swing arm
• 4. Vacuum gauge
• 5. Control panel
• 6. Bag pressing rod
• 7. Silicone strip
• 8. Air Switch
• 9. Sealing strip
• 10. Spring
• 11. (Part not clearly labeled in diagram, likely related to cover mechanism)
• 12. Heating strip
• 13. Tension spring
• 14. Circuit board
• 15. Heating transformer
• 16. Oil filler
• 17. Vacuum pump
• 18. Oil drain port
• 19. Exhaust solenoid valve
• 20. Air release solenoid valve
• 21. Circuit board

Parts List

Operating Instructions

1. Prepare the Machine: Push the door latch towards the center by hand and remove the side door. Unscrew the oil mist filter of the vacuum pump and fill it with oil. Ensure the oil level is between half and 3/4 of the oil window. Never start the vacuum pump without oil.
2. Panel Operation:
   • Display: Shows standby mode ('_') or deflation status ('00'). Numbers indicate vacuum, sealing, permanent temperature, or cooling status.
   • Emergency Stop Button (2): Use to stop the machine urgently.
   • VACUUM Time Setting (3): Press to set vacuum time (0-99S).
   • SEALING Time Setting (4): Press to set sealing time (0-9.9S).
   • SEALING TEMPERATURE Setting (5): Press to adjust sealing temperature (Low, Medium, High).
   • Cooling Time Setting: Hold key (5) for 5 seconds to set cooling time (0-9.9S).
   • INCREASE Key (6): Increases the value.
   • DECREASE Key (7): Decreases the value.
3. Usage Steps:
   1. Connect the power supply.
   2. Open the AIR SWITCH.
   3. Press the VACUUM button (3) and use INCREASE (6) or DECREASE (7) to set the vacuum time (approx. 25 seconds).
   4. Press the SEALING button (4) and use INCREASE (6) or DECREASE (7) to set the sealing time (approx. 2 seconds). Avoid excessively long sealing times to prevent burning the heating strip.
   5. Press the SEALING TEMPERATURE button (5) twice to select the MEDIUM indicator light for recommended temperature.
   6. Note: Pressing VACUUM (3) and DECREASE (7) together sets the permanent temperature to the factory default.
   7. Place the product in a vacuum chamber, ensuring the bag is flat on the sealing strip. Put down the bag pressing rod.
   8. Press the front edge of the vacuum cover by hand to start the machine. Once running, you can release the cover. The vacuum meter should indicate 0.06-0.08 MPa. The machine will automatically complete the packaging process.
4. Oil Change: When the machine requires an oil change or has been idle for a long time, loosen the screw under the oil window and drain the oil. It is recommended to replace the vacuum pump oil after 800 hours of continuous operation.

Circuit Diagram

A circuit diagram is provided, illustrating the electrical connections of the vacuum packing machine, including components like the motor (D), switches, relays, transformer, and solenoid valves.

Maintenance

1. After use, clean the machine surface and remove residual materials.
2. Store the machine in a clean, dry, and safe location away from children.
3. All maintenance, service, and repairs not covered in this manual should be performed by qualified service technicians.

Replace the High Temperature Cloth (Teflon Cloth):

1. Remove screws on both sides of the tray and lift the tray.
2. Remove the upper screws.
3. Remove the old high-temperature cloth.
4. Apply new high-temperature cloth.
5. Reinstall the original screws.
6. Complete the installation.

Replace the Chamber Sealing Strip:

1. Remove the Chamber Sealing Strip.
2. Inject new glass glue into the track to ensure air tightness.
3. Replace the Chamber Sealing Strip with a new one.
4. Complete the installation.

Troubleshooting and Solutions

Correct Disposal

This product complies with European Directive 2012/19/EC. The crossed-out wheelie bin symbol indicates separate collection for electrical and electronic devices. Do not discard with normal domestic waste; take it to a designated collection point for recycling.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai

EC REP: SHUNSHUN GmbH.
Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
Tel: +49 1727041930
Email: euvertreter@gmail.com

UK REP: Pooledas Group Ltd.
Unit 5 Albert Edward House, The Pavilions, Preston, United Kingdom
Tel: 01772418127
Email: pooledas123@gmail.com

Imported to AUS: SIHAO PTY LTD.
1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd.
Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Made In China