roadsafe.com.au
User Manual for ROADSAFE models including: RP-CRU70EV2 Recovery Tow Points, RP-CRU70EV2, Recovery Tow Points, Tow Points
Roadsafe Recovery Points Toyota Land Cruiser 76 78 79 Series 1999-on Rated Pair - 4x4 Works Model: Toyota Land Cruiser 76 78 79 Series – 1999-onRating (per recovery point): 5,000 kgQuantity: PairPosition: FrontFitting Hardware Included: YesFitting Instructions:
Recovery Tow Points Toyota 76 78 79 Series Landcruiser Extended Length V2
File Info : application/pdf, 3 Pages, 269.03KB
DocumentDocumentFITTING INSTRUCTIONS VEHICLE Toyota Landcruiser 76/78/79 Series (excluding 79 ANCAP S/C) PRODUCT Rated Recovery Point PRODUCT CODE RP-CRU70EV2 DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS For ease of fitting, we recommend: 1. Read the fitting instructions in their entirety. 2. Elevate the vehicle and ensure it is safely supported. 3. Remove front plastic undertray or aftermarket bash plate. To begin installation, identify the following parts: DRIVER SIDE Main Recovery Plate 9mm Spacer (Not required for ANCAP single cab 79) M12 x 120L Bolt, lock nut and 2x washers M10 x 60L Bolts M10 x 40L Bolts M10 Split washer + Flat washer 23X10.5x2 Washer 26X10.8x4 Washer 1 1 1 2 1 3 pairs 2 2 PASSENGER SIDE Main Recovery plate 9mm Spacer (Not required for ANCAP single cab 79) M10 x 110L Bolt, lock nut, and 2x washers M10 x 60L Bolts M10 x 40L Bolts M10 Split washer + Flat washer 23X10.5x2 Washer 26X10.8x4 Washer Crush tube 1 1 1 2 1 4 pairs 2 2 1 ENSURE ALL SUPPLIED AND SPECIFIED COMPONENTS ARE USED DURING THE INSTALLATION OF TOW RECOVERY POINTS, FAILURE TO DO SO WILL SIGNIFICANTLY REDUCE THE WORKING LOAD LIMIT (WLL) SPECIFIED FOR EACH INDIVIDUAL POINT, WHICH CAN RESULT IN SERIOUS INJURY OR DEATH. roadsafe.com.au A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279 VIC PH: 03 8687 1700 | QLD PH: 07 3737 7420 | Email: sales@roadsafe.com.au FITTING INSTRUCTIONS VEHICLE Toyota Landcruiser 76/78/79 Series (excluding 79 ANCAP S/C) PRODUCT Rated Recovery Point PRODUCT CODE RP-CRU70EV2 DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS 1. The Mounts themselves are sided, so please ensure installation to the correct side of the vehicle. After removing the undertray or bash plate undo the lower front steering box bolt and position plate as per figure 1. Note: The 25mm x 9mm yellow spacer is to be used in all applications except ANCAP rated 79 single cab models. 2. On the driver's side, use the M12 x 120mm bolt and 25mm x 9mm (see note) spacer to replace the factory steering box mounting bolt. 3. Use 2 M10 x 60mm bolts for the 2 lower holes which are spaced from the chassis and the M10 x 40mm for the hole against the chassis. 4. There are two different thickness washers to account for different front bar mount brackets, it is the discretion of the fitter to ensure the recovery point is evenly contacting the chassis rail at all points. 5. Continue to the passenger side, positioning the plate as per image 2. Figure 1 - Drivers side recovery point Figure 2 - Passengers side recovery point 6. Insert the crush tube and the M10 x110mm bolt into the top-rear mounting hole, again use 2 M10 x 60mm bolts for the 2 lower holes which are spaced from the chassis and the M10 x 40mm for the hole against the chassis. 7. All models have nuts retained in chassis on both sides, ready for fitment. 8. Ensure all bolts are fitted and torqued to recommended settings to ensure tow points meet tested standards. Bolt Torque Specs 8.8 10.9 12.9 M10 41-60Nm 59-85Nm 65-94Nm M12 71-105Nm 102-150Nm 114-164Nm RECOMMENDED FOR 4WD SPECIALIST MECHANICS TO FIT roadsafe.com.au A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279 VIC PH: 03 8687 1700 | QLD PH: 07 3737 7420 | Email: sales@roadsafe.com.au FITTING INSTRUCTIONS VEHICLE Toyota Landcruiser 76/78/79 Series (excluding 79 ANCAP S/C) PRODUCT Rated Recovery Point PRODUCT CODE RP-CRU70EV2 DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS 9. The RP-CRU70E have been designed to protrude next to the Roadsafe Skid Plate as shown in the images 1 & 2 above. 10.With some aftermarket skid plates you might need to trim two 100mm (long) x 40mm (wide) holes on each side to allow for the skid plate to be refitted. For the original Toyota undertray 2 small notches need to be done as per image 3 and 4. Figure 3 - Notching of plastic undertray Figure 4 - Undertray in place after notching roadsafe.com.au A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279 VIC PH: 03 8687 1700 | QLD PH: 07 3737 7420 | Email: sales@roadsafe.com.au