Braeburn Universal Programmable Smart Wi-Fi Thermostat

About Your Thermostat

Features

• Optional Wi-Fi connectivity – control and monitor thermostat from a smartphone, tablet or computer.
• 7 day, 5-2 day or non-programmable
• Auto or manual changeover
• Large 3 sq. in. bright blue backlit display is easy to read.
• Extra large display characters make viewing settings even easier.
• User selectable filter monitor reminds you of required filter maintenance.
• Precise temperature accuracy keeps you in control of your comfort.
• Convenient circulating fan mode

Thermostat Display

The thermostat display shows various indicators and information:

• 1 Room Temperature: Displays the current room temperature.
• 2 Hold Mode Indicator: Indicates if the thermostat is in HOLD mode.
• 3 Fan Indicator: Indicates when the system fan is running (?).
• 4 Wi-Fi Indicator: Indicates when connected to Wi-Fi (?). Flashes if connection is lost.
• 5 System Status Indicator: Displays information about the status of the system (e.g., HEAT ON ?, COOL ON ❄️).
• 6 Set Temperature: Displays the current set point temperature.
• 7 Low Battery Indicator: Indicates when the batteries need to be replaced (?).
• 8 Time of Day: Displays the current time of day.
• 9 Program Event Indicator: Displays the current program event (e.g., MORN, DAY, EVE, NIGHT).
• 10 Day of the Week: Displays the current day of the week (e.g., TU).

Thermostat Buttons and Controls

The thermostat features the following buttons and controls:

• SYSTEM Button: Selects the system mode (AUTO, COOL, OFF, HEAT, EMER).
• PROG Button: Selects programming mode or press for 3 seconds to select SpeedSet®.
• HOLD Button: Enters/Exits the HOLD mode (program bypass).
• RETURN Button: Returns to normal mode from program or a program override.
• DAY/TIME Button: Sets the current time and day of the week.
• FAN Button: Selects the system fan mode (AUTO, ON, CIRC).
• SpeedBar (⬆️/⬇️): Increases or decreases settings (time, temperature, etc.).
• RESET Button: Resets current time, program, and user settings. Located in a small hole on the front.

The Quick Reference Instructions are stored in a slot at the top of the thermostat.

The Battery Compartment is located in the back of the thermostat.

Setting User Options

Advanced User Options

User options allow customization of thermostat features. Most users will not need to make changes.

To access the User Options menu, press and hold the RETURN button for approximately 3 seconds until the screen changes and displays the first User Option. Use the SpeedBar (⬆️/⬇️) to change the setting and RETURN to advance to the next option.

Table of User Options

NOTE: Some user options may not be available depending on how your thermostat was configured in the Installer Settings.

Detailed User Option Descriptions

Filter Service Monitor (User Option 1)

A user-selectable service monitor displays a reminder for air filter replacement. The display will flash "SRVC FLTR" when the service interval is reached. Press RETURN to reset the timer after replacement. Select OFF or a set number of days before the reminder appears.

Extended Hold Period (User Option 2)

Determines how long the thermostat holds a set temperature when HOLD mode is activated. LONG holds indefinitely. 24 HRS holds for 24 hours, then returns to the program. Not available in non-programmable mode.

Thermostat Lock Code (User Option 3)

Sets a 3-digit code to lock or unlock the thermostat. Setting the code here does not activate the lock feature.

Wi-Fi Clear (User Option 4)

Use this setting if you no longer want to be connected to Wi-Fi or change routers. Select WIFI to skip changes. Select WIFI CL to clear all Wi-Fi network settings.

Setting Your Program Schedule

Setting the Time and Day

1. In normal operating mode, press the DAY/TIME button. The hour will flash.
2. Press SpeedBar (⬆️/⬇️) to adjust the hour, then press DAY/TIME.
3. Press SpeedBar (⬆️/⬇️) to adjust the minute, then press DAY/TIME.
4. Press SpeedBar (⬆️/⬇️) to adjust the day of the week.
5. Press RETURN to exit.

NOTE: If Wi-Fi is used, the clock adjusts automatically to the time zone and DST set in the Wi-Fi feature.

Tips Before Setting Your Program Schedule

• Ensure current time and day of the week are correct.
• Verify AM and PM indicators are correct during programming.
• Installer settings (e.g., auto changeover, temperature limits) may affect programming flexibility.
• The NIGHT event cannot exceed 11:50 p.m.

Programming Options

This thermostat supports one of the following programming options:

• 7-day programming mode with 4 events per day (default)
• 5-2 (weekday/weekend) programming mode with 4 events per day
• Non-Programmable mode

NOTE: If configured as non-programmable, pressing PROG or HOLD will display "NONE".

Program changes can also be made via the BlueLink Smart Connect® application.

Energy Saving Programs (Default Settings)

The thermostat comes with pre-programmed energy saving schedules. If these suit your needs, no further programming is necessary.

Residential 7 Day Programming (Factory Settings)

Residential 5-2 Day Programming (Weekday/Weekend Factory Settings)

Programming a 7 Day Residential Schedule

This mode allows programming individual days or the entire week using a 4-event schedule.

Setting All 7 Days at Once (SpeedSet®)

NOTE: Setting all 7 days at once overwrites any previously programmed individual days.

1. Hold PROG for 3 seconds. The display switches to SpeedSet mode, showing all 7 days with the hour flashing.
2. Press SYSTEM to select HEAT or COOL.
3. Press SpeedBar (⬆️/⬇️) to adjust the hour for the MORN event, then press PROG.
4. Press SpeedBar (⬆️/⬇️) to adjust the minute for the MORN event, then press PROG.
5. Press SpeedBar (⬆️/⬇️) to adjust the temperature for the MORN event, then press PROG.
6. Repeat steps 3-5 for the DAY, EVE, and NIGHT events.
7. If needed, repeat steps 2-6 to program the opposite mode (HEAT or COOL).
8. Press RETURN to exit.

Setting Individual Days (7 Day Residential)

1. Press PROG. The display switches to programming mode, showing M (Monday) with the hour flashing.
2. Press SYSTEM to select HEAT or COOL.
3. Press DAY/TIME to select the day you wish to program.
4. Press SpeedBar (⬆️/⬇️) to adjust the hour for the MORN event, then press PROG.
5. Press SpeedBar (⬆️/⬇️) to adjust the minute for the MORN event, then press PROG.
6. Press SpeedBar (⬆️/⬇️) to adjust the temperature for the MORN event, then press PROG.
7. Repeat steps 4-6 for DAY, EVE, and NIGHT events.
8. If needed, repeat steps 3-6 to select a different day.
9. If needed, repeat steps 2-8 to program the opposite mode (HEAT or COOL).
10. Press RETURN to exit.

Operating Your Thermostat

Setting the SYSTEM Control Mode

The System Control has 5 modes: AUTO, COOL, OFF, HEAT, and EMER. Select modes by pressing the SYSTEM button.

NOTE: Some system modes may not be available depending on thermostat configuration.

• AUTO: System cycles between heating and cooling based on program set points. Displays "AUTO" with either HEAT or COOL.
• COOL: Only the cooling system operates.
• OFF: Heating and cooling systems are off.
• HEAT: Only the heating system operates.
• EMER: Operates a backup heat source (Emergency Heat) for heat pump systems only.

Setting the FAN Control Mode

The Fan Control has 3 modes: AUTO, ON, and CIRC. Select modes by pressing the FAN button.

NOTE: Some fan modes may not be available depending on thermostat configuration.

• AUTO: System fan runs only when heating or cooling system is running.
• ON: System fan stays on continuously.
• CIRC: System fan runs intermittently to circulate air and provide even temperature distribution when the heating or cooling system is not active.

Setting the Temperature

Temporary Adjustment

Press the SpeedBar (⬆️/⬇️) to adjust the current set temperature. In 5-2 or 7-day programmable mode, the temperature reverts to the programmed setting at the next scheduled change.

Extended Adjustment

Press the HOLD button so "HOLD" appears. Then, press the SpeedBar (⬆️/⬇️) to adjust the current set temperature. (See Extended Hold Period, page 10).

NOTE: Non-programmable thermostats do not have a HOLD option.

Status Indicators

These indicators appear on the display to show system status:

• HEAT ON: Heating system is running (?).
• COOL ON: Cooling system is running (❄️).
• AUX: Auxiliary stage of heating is running (multi-stage heat pump systems only).
• EMER: Emergency heating system is running (heat pump systems only).
• ADJ: Temperature adjustment limit has been reached.
• Wi-Fi Indicator (?): Thermostat is connected to Wi-Fi network (flashes if connection is lost).
• Low Battery Indicator (?): Thermostat battery is low.

Program Event Indicators

These indicators show which part of your current program is active (MORN, DAY, EVE, NIGHT). If flashing, the program has been temporarily bypassed and will resume at the next scheduled event. Not visible in HOLD or Non-Programmable Mode.

Resetting the Thermostat

A reset button erases all user settings and programming but does not affect Installer Settings. Use a small object (e.g., toothpick) to gently press the button labeled "RESET" inside the small hole on the thermostat housing. You cannot reset if the thermostat is locked.

Additional Operation Features

Auto Changeover Mode

This feature is enabled/disabled in Installer Settings. If enabled, select it by pressing SYSTEM until "AUTO HEAT" or "AUTO COOL" appears. The system automatically switches between heating and cooling based on programmed set points and a "dead band" setting to prevent conflicts. The default dead band is 3° F.

Adaptive Recovery Mode (ARM™)

This feature, enabled/disabled in Installer Settings, automatically adjusts the start time based on room temperature.

• ARM ON: Reaches temperature BY the scheduled time (e.g., turns on early to reach 70° by 7:00 AM).
• ARM OFF: Starts to change temperature AT the scheduled time (e.g., starts heating at 7:00 AM).

Setting the thermostat to Hold, Emergency Heat, or manually adjusting the temperature will interrupt ARM.

Compressor Protection

This feature is present in cooling/heating modes and includes an automatic delay after turning off the system compressor to prevent damage from short cycling.

Locking and Unlocking the Thermostat

Your 3-digit Lock Code is set in "User Options". To lock or unlock:

1. Press and hold DAY/TIME and HOLD buttons together for 5 seconds. The screen displays "000".
2. Press SpeedBar (⬆️/⬇️) to enter the first digit of your lock code, then press RETURN.
3. Repeat for the second and third digits.
4. After the third digit, press RETURN.

If a valid code is entered, the thermostat will lock or unlock (depending on its previous state). The display will show "LOCK". If an invalid code is entered, "NO" will briefly appear.

Thermostat Maintenance

Thermostat Cleaning

Never spray liquid directly on the thermostat. Use a soft, damp cloth to wipe the outer body. Do not use abrasive cleansers.

Changing the Batteries

This thermostat requires two (2) "AA" alkaline batteries for clock and power if 24-volt AC power is not connected.

If batteries become low, a battery indicator (?) will appear. Change batteries immediately:

1. Gently pull the thermostat body from its base.
2. Remove old batteries and insert new ones, ensuring correct (+) and (-) orientation.
3. Gently push the thermostat body back onto the base.

NOTE: Replace batteries annually or if the thermostat will be unattended for an extended period.

Limited Warranty

When installed by a professional contractor, this product is backed by a 5-year limited warranty. Limitations apply.

For full warranty details, terms, and conditions:

• Visit online: www.braeburnonline.com/warranty
• Phone: 866.268.5599
• Write: Braeburn Systems LLC, 2215 Cornell Avenue, Montgomery, IL 60538