360 Dash Cam G980H User Manual

Product Appearance

The 360 Dash Cam G980H features a sleek design with clearly identifiable components for ease of use and installation.

• Top View: Includes a removable back panel, the main camera lens, settings button, power button, and microphone button.
• Bottom View: Features a USB Power Port, connection for a rear camera, the main screen, and a TF card slot for storage.

Packing List

Upon opening the package, please verify that all accessories are included and the dash cam is in good condition:

1. Main unit x 1
2. USB power cord x 1
3. Electrostatic film x 1
4. User manual x 1
5. Installation pry bar x 1
6. Car charger x 1
7. Rear camera x 1

Installation

1) Install the electrostatic film:

Install the electrostatic film on the front windshield within the recommended dashed area. Before installation, clean the glass thoroughly and ensure no bubbles are present between the film and the glass.

Tip: For optimal coverage of the car's front view and improved ADAS accuracy, install the dash cam as close to the middle area above the front windshield as possible.

2) Attach the dash cam:

Remove the 3M adhesive protective film from the dash cam bracket. Attach the bracket to the electrostatic film and adjust the dash cam to the appropriate angle.

Removal and installation of the dash cam:

To remove the dash cam, slide it upwards in the direction of the arrow until a "click" sound is heard, indicating it's ready to be taken down. To install, align the hole on the back of the dash cam bracket with the snap position on the 3M adhesive, and slide the bracket downwards until a "click" sound is heard, indicating secure installation.

3) Wiring and installation of the rear camera:

Extend the rear camera cable along the top of the windshield, down the A-pillar, and along the roofline, routing it towards the vicinity of the trunk.

4) Wiring and connecting the power supply:

Route the power cord along the top of the front windshield, through the A-pillar, and into the storage compartment near the front passenger seat's cigarette lighter port. Connect the power cord to the cigarette lighter power supply.

Tip: Use the included wiring pry bar to tuck the power cord under the A-pillar sealant strip. Note that cigarette lighter port positions may vary by vehicle.

ADAS Calibration Guide

To ensure ADAS accuracy, calibration is essential before use. The dash cam powers on automatically and begins recording after wiring is complete. ADAS calibration is required upon first power-up. (If not the first power-up, access ADAS calibration in the driving assistance section of the settings menu.)

1. Step 1: Adjust the dash cam's installation position to align the vertical line of ADAS calibration with the vehicle's centerline as much as possible.
2. Step 2: Adjust the camera angle to align the horizontal line with the road's horizon (where the road meets the distance).
3. Step 3: Once calibration is complete, ADAS functions will become effective. Refer to the electronic manual for detailed ADAS function triggering conditions and alert content.

Download and Installation of the App

Method 1: Scan the QR code below to download and install the app. The QR code is represented by a square pattern with a small circle in the center. This QR code links to the Botslab APP.

Method 2: Search for "botslab" in major application stores and download the Botslab app.

User Guide

Scan the QR code to access the online version of the Quick Start Guide and obtain more detailed instructions on how to use the dash cam. The QR code is a square pattern of black and white modules.

Precautions for Using the Dash Cam

• This product is an auxiliary device (dash cam) for safe driving.
• The company is not responsible for any losses resulting from product malfunctions, data loss, or product usage.
• This product is designed to record external images of vehicles. Some functions may not be supported due to varying driving and vehicle environments.
• Firmware upgrades are periodic and may cause changes in product performance or image capture issues due to usage environment. Recorded driving images are for reference only.
• While this product can record accident images, it does not guarantee all accident images will be recorded. Minor collisions may not activate the collision sensor.
• Do not install or operate this product while the vehicle is in motion.
• This product must be directly connected to the car's power supply system and installed by professionals. Do not use for extended periods without the engine running.
• This device may interfere with improperly protected medical devices. Consult a doctor or medical device manufacturer if uncertain about RF energy shielding.
• Do not subject this product to strong shocks or vibrations.
• Stop using the product before cleaning or maintenance.
• Do not use chemical solvents or cleaning agents.
• Do not disassemble or modify this product without authorization.
• Normal operating temperature range: 0°C to 50°C.
• Ensure use within legal limits.

Important Statement

Personal Information Security

To ensure the safety of you and your family, ensure your product is only bound by authorized persons. 360 implements strict measures to secure your and your family's information.

FCC regulatory conformance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Attentions And After-Sales Service

I. Introduction and declaration of after-sales service

• Use only accessories provided by the original manufacturer to avoid malfunctions or damage. Failure to do so or using incompatible accessories will void the warranty. The company assumes no responsibility for danger or damage from unauthorized uses. Dismantling or changing the product housing will also void the warranty.
• The company is committed to constant improvement and sustainable development, and may modify the product manual without advance notice.
• Unless specified by applicable laws, manual contents are based on product manufacturing conditions. No explicit or tacit warranty is made for the correctness, reliability, or contents of the files.
• The product manual is protected by copyright law. Copying, transmitting, distributing, or using it in other forms is forbidden without 360's written approval.

II. In regards to service policies within the warranty period of the 360 dash cam:

1. This product has a one-year warranty. Contact local authorized distributors for details.
2. The warranty period for the power adapter and charger cable is 12 months, and for the battery, it is 6 months.
3. Non-electronic accessories are not covered by the warranty.

♻ This symbol, a crossed-out wheeled bin, indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information, contact your local municipality, disposal service, or the shop where you purchased the product.

List of Performance Faults of 360 Dash Cam

III. Charged maintenance policies of 360 recorder product

The 360 Company or its authorized service centers will provide reasonable maintenance services at a cost for cases outside the warranty scope, including:

1. Exceeding the valid warranty period.
2. Lack of warranty certificate or valid invoice, or if the certificate does not match the product model/labeling, or has been tampered with.
3. Damage from usage, repair, and maintenance not following User Manual requirements. Damage or malfunction from personal removal, maintenance, or unauthorized modification of system software.
4. Collision, soaking, breaking, or burning of the printed circuit board.
5. Cracking or damage to the outer shell, LCD screen, antenna, etc., during use, except for structural/material factors.
6. Damage due to force majeure.

RF Exposure

CE:

EU regulatory conformance: RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20cm between the device and the human body. To comply with RF exposure requirements, it is recommended to use the product while maintaining a distance of 20cm between the device and the human body.

CE DOC

Hereby, Botslab Inc. declares that the radio equipment type G980H-N529-1 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://www.botslab.com

Manufacturer information:

Company name: Botslab Inc.

Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA

Operation temperature: 0~50°C

Operation frequency (Max power):

• Wifi: 2412MHz-2472MHz (<20dBm), 5745MHz-5825MHz (<13.98dBm)
• Bluetooth: 2402MHz-2480MHz (<13dBm)

FCC:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Responsible party (contact for FCC matters only):

Botslab Inc.

919 North Market Street, Suite 950, Wilmington, New Castle, Delaware

www.botslab.com

Warranty Card

This section outlines a template for user and product information, along with a repair record. It includes fields for:

1) User Information

• Name
• Tel
• E-mail
• Post Code
• Address

2) Product Information

• Color
• SN (Serial Number)

3) Repair Record

A table is provided to log service records, including fault information, service date, and signature.