HD6700 Code Reader User Manual

Specifications

• Warranty: 2 years
• Light Source: 650 Laser
• Processor: ARM Cortex 32-bit
• Scan Acknowledgement: Light and Sound Signal
• Scan speed: 500 scans/second
• Wireless Communication: 2.4 G
• Wireless range: up to 100 meters in open spaces
• Built-in Memory: 16Mb
• Memory capacity: up to 50,000 codes
• Battery Capacity: 1800mA
• Operating Current: 1A
• Charging Voltage: 5V
• Operating time: up to 24 hours with 1D codes and up to 16 hours with 2D codes
• Charging Time: 4 hours
• Standby Time: 30 days
• Interface: USB
• Drop resistance: up to 1.5 meters
• Device dimensions: 16 x 9.5 x 6.5 cm
• Package dimensions: 17 x 11.5 x 7.5 cm
• Device weight: 200 g
• Package weight: 290 g
• Operating Temperature: 0 to 40 degrees
• Storage Temperature: -40 to 60 degrees
• Moisture: 5% to 95%
• Readable ID codes: Codabar, Code 11, Code 93, MSI, Code 128, UCC/EAN-128, Code 39, EAN-8, EAN-13, UPC-A, ISBN, Industrial 2 of 5, Interleaved 2 of 5 (ITF), Standard 2 of 5, Matrix 2 of 5
• Readable 2D codes: QR, DataMatrix, PDF 417, Aztec, Xanxin, MicroPDF

Kit Contents

• Wireless Multi-Dimensional Code Reader
• USB charging cable
• USB Receiver
• Manufacturer's manual in paper form
• User manual in electronic form in Polish

Features

• Scanning: manual (push-button)
• Scan speed: 500 scans/second
• Wireless range: up to 100 meters in open spaces
• Internal memory capacity: up to 50,000 scanned codes

Master Codes

Scan the following codes to perform specific functions:

• Restore to settings: [Barcode image representing Restore to settings]
• Factory Reset: [Barcode image representing Factory Reset]
• Software version: [Barcode image representing Software version]
• Battery level: [Barcode image representing Battery level]

Case Settings

Configure the case sensitivity for scanned data:

• Lowercase: [Barcode image representing Lowercase]
• Uppercase letters: [Barcode image representing Uppercase letters]
• No case conversion: [Barcode image representing No case conversion]

Pairing the Scanner with the USB Receiver

1. To pair the reader with a USB receiver for radio communication, first scan the code below: [Barcode image representing pairing code 1]
2. In the next step, you need to scan the code below: [Barcode image representing pairing code 2]
3. Finally, plug the receiver into your computer's USB port. A single beep indicates that the reader is correctly paired with the receiver.

Beep Settings

Control the audible feedback of the scanner:

• Beep off: [Barcode image representing Beep off]
• Beep on: [Barcode image representing Beep on]

Sleep Time Settings

Configure the scanner's sleep mode to conserve battery:

• Sleep after 1 minute: [Barcode image representing Sleep after 1 minute]
• Sleep after 5 minutes: [Barcode image representing Sleep after 5 minutes]
• Sleep after 10 minutes: [Barcode image representing Sleep after 10 minutes]
• Sleep after 30 minutes: [Barcode image representing Sleep after 30 minutes]
• Sleep off: [Barcode image representing Sleep off]
• Instant Sleep: [Barcode image representing Instant Sleep]

Endpoint Settings

Configure the end-of-line characters for scanned data:

• CR: [Barcode image representing CR]
• LF: [Barcode image representing LF]
• CR+LF: [Barcode image representing CR+LF]
• CR + LF cancellation: [Barcode image representing CR + LF cancellation]

2.4G Mode Baud Rate Settings

Adjust the transmission speed for 2.4G mode:

• High transmission speed: [Barcode image representing High transmission speed]
• Average transmission speed: [Barcode image representing Average transmission speed]
• Slow transmission speed: [Barcode image representing Slow transmission speed]
• Very low transmission speed: [Barcode image representing Very low transmission speed]

Barcode Transfer Modes

Choose how scanned data is transferred:

1. Real mode: Codes are sent directly to your computer immediately after scanning. [Barcode image representing Real-world mode]
2. Storage mode: Scanned codes are saved in the built-in memory of the device, which can be later transferred to a computer. [Barcode image representing Storage mode]

Amount of data stored: [Barcode image representing Amount of data stored]

Data transfer: [Barcode image representing Data transfer]

Deleting data: [Barcode image representing Deleting data]

Hide Start and End Characters

Configure the scanner to omit specific characters from the beginning or end of scanned data:

• Hiding leading characters: [Barcode image representing Hiding leading characters]
• Hiding trailing characters: [Barcode image representing Hiding trailing characters]

Number of characters to hide:

• 1x: [Barcode image representing 1x]
• 2x: [Barcode image representing 2x]
• 3x: [Barcode image representing 3x]
• 4x: [Barcode image representing 4x]
• 5x: [Barcode image representing 5x]
• 6x: [Barcode image representing 6x]
• 7x: [Barcode image representing 7x]
• 8x: [Barcode image representing 8x]
• 9x: [Barcode image representing 9x]
• 10x: [Barcode image representing 10x]
• 11x: [Barcode image representing 11x]
• 12x: [Barcode image representing 12x]
• 13x: [Barcode image representing 13x]
• 14x: [Barcode image representing 14x]
• 15x: [Barcode image representing 15x]
• 16x: [Barcode image representing 16x]

Canceling Starting Characters: [Barcode image representing Canceling Starting Characters]

Cancel trailing characters: [Barcode image representing Cancel trailing characters]

Prefix and Suffix Settings

• Display signs:
  • Prefix setting: [Barcode image representing Prefix setting]
  • Suffix setting: [Barcode image representing Suffix setting]
• Control characters:
  • Character Set 0: [Barcode image representing Character Set 0]
  • Character Set 1: [Barcode image representing Character Set 1]
  • Character Set 2: [Barcode image representing Character Set 2]
  • Character Set 3: [Barcode image representing Character Set 3]

Prefix setting: [Barcode image representing Prefix setting]

Suffix setting: [Barcode image representing Suffix setting]

Cancel a prefix: [Barcode image representing Cancel a prefix]

Cancel a suffix: [Barcode image representing Cancel a suffix]

Virtual COM Mode for Radio Communication

Virtual COM: [Barcode image representing Virtual COM]

Pairing with a USB receiver: After reading the above codes, connect the receiver to the USB port of the computer.

Appendix 1. Control Character Table

Appendix 2. Display Signs