HD10C Wired Barcode Scanner with Stand - User Manual

This document provides instructions for the HD10C wired barcode scanner with a stand.

Specifications

• Light Source: 620nm LED
• Sensor Type: CMOS
• Scanning Method: Manual (button press) / Automatic (proximity detection)
• Scan Confirmation: Light and sound signal
• Read Speed: 200 scans/second
• Interface: USB
• Cable Length: 140 cm
• Protection Rating: IP54
• Device Dimensions: 16 x 9.5 x 6.5 cm
• Stand Dimensions: 24 x 12 x 12 cm
• Package Dimensions: 18.5 x 12 x 8.5 cm
• Device Weight: 300 g
• Weight with Packaging: 370 g
• Operating Temperature: -20 to 50°C
• Storage Temperature: -40 to 60°C
• Readable 1D Codes: EAN-8, EAN-13, UPC-A, UPC-E, CODE 128, CODE 39, CODE 93, CODE 11, CHINESE 2 of 5, CODABAR, MSI, Interleaved 2 of 5 (ITF), and other 1D codes.

Package Contents

• Barcode scanner
• DIY stand for the scanner
• Built-in USB communication cable
• User manual

Features

• Wired scanner for standard barcode scanning.
• Can scan barcodes displayed on LCD, LED/OLED screens, and mobile device displays.
• Supports automatic scanning mode.
• Allows programming of any character before or after the scanned code.

Restoring to Factory Settings

Scan the barcode labeled 'Przywróć ustawienia domyślne' to restore the scanner to its factory default settings.

Scanning Modes

Manual Scan: Press the trigger button to scan.

Automatic Scan: The scanner automatically activates when a barcode is detected within its range.

Buzzer Settings

Buzzer On (Default): The scanner will emit a sound to confirm a successful scan.

Buzzer Off: The scanner will not emit a sound upon a successful scan.

End Character Settings

• CR (Carriage Return): Appends a carriage return character after each scan.
• TAB: Appends a tab character after each scan.
• LF+CR (Line Feed + Carriage Return): Appends line feed and carriage return characters.
• No Characters: No additional characters are appended.

Case Settings

• Upper and Lower Case: No case conversion is applied to scanned data.
• Uppercase Only: Converts all scanned letters to uppercase.
• Lowercase Only: Converts all scanned letters to lowercase.

Scanning Reversed Codes (Black Background)

• Enabled: Allows scanning of inverted barcodes (white bars on a black background).
• Disabled (Default): The scanner operates in the standard mode for black bars on a white background.

Adding Prefix and Suffix

To set a prefix or suffix, first scan the 'Add Prefix' or 'Add Suffix' barcode. Then, scan the desired character(s) from the character table. Finally, scan the 'Save Settings' barcode.

• Add Prefix: Scan this to begin setting a prefix.
• Add Suffix: Scan this to begin setting a suffix.
• Cancel Prefix: Scan this to remove any set prefix.
• Cancel Suffix: Scan this to remove any set suffix.

Hiding Barcode Characters

Hiding Leading Characters: To hide a specified number of characters from the beginning of a barcode, first scan the 'Hide Leading Characters' barcode, then scan the corresponding number codes from the character table, and finally scan the 'Save Settings' barcode.

Hiding Trailing Characters: To hide a specified number of characters from the end of a barcode, first scan the 'Hide Trailing Characters' barcode, then scan the corresponding number codes from the character table, and finally scan the 'Save Settings' barcode.

Character Table

The following table lists control characters and alphanumeric characters that can be programmed as prefixes, suffixes, or for hiding barcode characters.

Function Key Barcodes

The following barcodes represent function keys that can be programmed:

Function Key	Barcode
F1		HD43 Barcode Scanner: Programming '~' as a Prefix Guide on how to program the tilde (~) character as a prefix for the HD43 barcode scanner by scanning specific codes. Features WIFI connectivity and built-in memory.