StarTech.com IH2006-KVM-EXTENDER HDMI KVM Console Extender over IP - 4K 60Hz

Transmitter and Receiver Diagrams

Diagram of the Transmitter unit. It shows a rectangular device with several ports labeled with numbers. From left to right, top row: Port 1 (Reset), Port 2 (KVM LED), Port 3 (Audio In), Port 4 (RS-232), Port 5 (Service). Bottom row: Port 6 (USB-C Host), Port 7 (HDMI Input), Port 8 (HDMI Output), Port 9 (Network), Port 10 (5V 2A DC).

Diagram of the Receiver unit. It shows a rectangular device similar to the transmitter. From left to right, top row: Port 1 (Reset), Port 2 (KVM LED), Port 11 (HID), Port 4 (RS-232), Port 5 (Service). Bottom row: Port 9 (Network), Port 8 (HDMI Output), Port 10 (5V 2A DC).

Components and Functions

Product Information

For the latest product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/IH2006-KVM-EXTENDER

Package Contents

• KVM Extender Transmitter x 1
• KVM Extender Receiver x 1
• RS-232 Terminal Headers x 2
• Mounting Kit x 2
• Set of Rubber Feet x 2
• Universal Power Adapter (NA/EU/UK) x 2
• Quick-Start Guide x 1

Installation

(Optional) Install the Mounting Bracket

1. Determine the Mounting Surfaces for the KVM Extender Transmitter and Receiver.
2. Place the Mounting Brackets on each side of the KVM Extender Transmitter. Align the Holes in the Mounting Brackets with the Holes on the sides of the KVM Extender Transmitter.
3. Insert two of the included Screws through each Mounting Bracket and into the KVM Extender Transmitter.
4. Tighten each Screw using a Phillips Head Screwdriver.
5. Mount the KVM Extender to the desired Mounting Surface using the appropriate Mounting Hardware (e.g. Wood Screws).
6. Repeat Steps 2 to 5 for the KVM Extender Receiver.

Installing the Transmitter and Receiver

1. Position the Transmitter near the Host Computer.
2. Connect an HDMI Cable (sold separately) from the Host Computer to the HDMI Input Port on the Transmitter.
3. Connect a USB Type-C Cable (sold separately) from the Host Computer to the USB-C Host Port on the Transmitter.
4. (Optional) Connect an HDMI Cable (sold separately) from the HDMI Output Port on the Transmitter to a Local HDMI Display.
5. (Optional) Connect a 3.5mm Audio Cable (not included) from an Audio Source to the Audio Input Port on the Transmitter.
6. Position the Receiver near the HDMI Display Device.
7. Connect an Ethernet Cable (sold separately) from the Network Port on the Transmitter to a Network Hub, Switch, or Router.
8. Connect an HDMI Cable (sold separately) from the HDMI Output Port on the Receiver to the HDMI Display Device.
9. Connect a USB Mouse and Keyboard to the USB HID Ports on the Receiver.
10. (Optional) Connect a 3.5mm Audio Cable (sold separately) from the Audio Output Port on the Receiver to an Audio Device (e.g. Speakers).
11. Connect an Ethernet Cable (sold separately) from the Network Port on the Receiver to a Network Hub, Switch, or Router.
12. Connect the included Universal Power Adapters to the DC Input Port on the Transmitter and Receiver and to an Electrical Outlet.

LED Chart

Regulatory Compliance

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit than the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. If shielded interface cables are included with the product, or if additional components or accessories are designated for use with the installation, they must be used to ensure compliance with FCC regulations.

ISED Statement / Dclaration d'ISED

CAN ICES-003(B) / NMB-003(B)

This Class B digital apparatus complies with Canadian ICES-003. This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Le prsent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

EU REACH Declaration

This product complies with the Registration, Evaluation, Authorisation, and Restriction of Chemicals (REACH) Regulation (EC) of the European Parliament and the Council. The product does not contain any of the Substances of Very High Concern (SVHC) or Restricted Substances above the threshold values declared by the European Agency for Chemicals (ECHA) on their website's documented/maintained lists.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders. PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

StarTech.com Contact Information

StarTech.com Ltd.
45 Artisans Crescent
London, Ontario N5V 5E9
Canada

StarTech.com LLP
4490 South Hamilton Road
Groveport, Ohio 43125
U.S.A.

StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills, Northampton NN4 7BW
United Kingdom

StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands

For support in other regions: startech.com/fr | startech.com/de | startech.com/es | startech.com/nl | startech.com/it | startech.com/jp

Support

For additional self-service support options and community forums, please visit: www.StarTech.com/support