⚠️ SAFETY INSTRUCTIONS
WARNING IMPORTANT INSTRUCTION
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, injury to persons, and hyperthermia, including the following:
- Read all instructions before using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Always unplug heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
- To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.
- CAUTION: Risk of Fire – Do Not Operate Without Legs (Base) Attached.
SAVE THESE INSTRUCTIONS
▲ WARNING
- INGESTION HAZARD: This product contains a button cell or coin battery.
- DEATH or serious injury can occur if ingested.
- A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
- KEEP new and used batteries OUT OF REACH of CHILDREN
- Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
a) Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
b) Even used batteries may cause severe injury or death.
c) Call a local poison control center for treatment information.
d) Compatible battery for remote control is CR2025.
e) Nominal battery voltage is 3V.
f) Non-rechargeable batteries are not to be recharged.
g) Do not force discharge, recharge, disassemble, heat above (manufacturer's specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage orexplosion resulting in chemical burns.
h) Ensure the batteries are installed correctly according to polarity (+ and -).
i) Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
j) Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
k) Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
01 PACKING LIST
After opening the device packaging, verify that the device is undamaged and check the accessories against the diagram below to ensure they are complete.
- Heater Main Unit x1
- User guide x1
- Support Feet x4
- Filter x1
- Remote Control x1
Diagram Description: Visual representation of the heater main unit, user guide, support feet, filter, and remote control.
02 APPLIANCE OVERVIEW
Diagram Description: An illustration of the heater showing the following parts: Heatable Cat Bed, Control Panel, Filter, Power Cord, Support Feet. The control panel has four circular buttons. The main body is supported by three angled legs.
03 PRODUCT SIZE
Diagram Description: Front view of the heater with dimensions indicated. Width: 473.5 mm. Height: 432.5 mm.
Design is subject to change without prior notice!
04 PRODUCT INSTALLATION
Installation: Rotate the support feet.
Diagram Description: Close-up view of the bottom of the heater showing how to attach and rotate the support feet into place. Arrows indicate rotation.
05 OPERATING INSTRUCTIONS
Control Panel Icons
The control panel features icons for different modes:
- ? Fan Mode
- ? Heating Mode (with Low/High indicators)
- ☁️ Cat Bed Mode (with H1/H2 indicators)
- ⏻ Power/Standby
- Indicator Light
Power/Standby
Power On: In standby mode, press the ⏻ Button once to turn on the heater. The indicator light will illuminate red.
Standby: While the heater is on, press the ⏻ Button once to switch to standby mode. The indicator light will turn off.
Diagram Description: Illustration showing the power button being pressed to turn the device on or off.
Cat Bed Mode
H1 Heating Mode: While heating is off, press the ☁️ Button once to activate H1 mode. The H1 indicator light will illuminate white.
H2 Heating Mode: In H1 mode, press the ☁️ Button once to activate H2 mode. The H2 indicator light will illuminate white.
Turn Off Heating: In H2 mode, press the ☁️ Button once to turn off heating. The indicator light will turn off.
Diagram Description: Visual guide showing the sequence of pressing the Cat Bed Mode button to cycle through H1, H2, and OFF states.
Heating Mode
Warm Air Mode: While heating is off, press the ? Button once to activate Warm Air Mode. The Low indicator light will illuminate white.
Hot Air Mode: In Warm Air Mode, press the ? Button once to activate Hot Air Mode. The High indicator light will illuminate white, and the Low indicator light will turn off.
Turn Off Heating: In Hot Air Mode, press the ? Button once to turn off heating. The indicator light will turn off.
Diagram Description: Visual guide showing the sequence of pressing the Heating Mode button to cycle through Warm Air (Low), Hot Air (High), and OFF states.
Fan Mode
Fan Mode: Press the ? Button once to activate Fan Mode. The indicator light will illuminate white.
Note: Fan Mode delivers airflow without heating.
Diagram Description: Visual guide showing the Fan Mode button being pressed, activating the fan icon and indicator light.
06 SET UP AND USE
PLEASE SCAN THE QR CODE FOR DETAILED SETUP AND USAGE INSTRUCTIONS.
QR Code Description: A placeholder for a QR code that would link to more detailed setup and usage instructions. (QR code itself is excluded as per instructions).
07 CLEANING AND MAINTENANCE
Maintenance and Care
- When the product is not in use, turn off the power switch and unplug the power supply.
- Before cleaning or maintenance, disconnect the power supply and allow the product to cool down.
- Wipe the main unit with a clean, soft, damp cloth. Ensure no water enters the product during cleaning.
- DO NOT use solvents such as alcohol, gasoline, acetone, or toluene for cleaning, as they may cause discoloration or corrosion of the exterior.
- Avoid bumping or scratching the product to prevent surface damage.
Filter Replacement
Diagram Description: Two images illustrating filter replacement. The first shows removing the filter cover. The second shows taking out the old filter and inserting a new one, then reattaching the cover.
Note: Never change filter while device is running.
08 PRODUCT SPECIFICATIONS
Product: Pet-Friendly Space Heater
Model: PH20
Rated Voltage: 120V AC
Rated Frequency: 60Hz
Power: 1500W
Product Size: 18.6x18.6x17 inch (473.5x473.5x432.5 mm)
Net Weight: 10.4 lb (4.7 kg)
Gross Weight: 15.0 lb (6.8 kg)
Material: ABS
Color: White
09 TROUBLESHOOTING
| Common Fault | Fault Description | Fault Solutions |
|---|---|---|
| No Power | Power Cord Not Inserted or Poorly Connected Heater Not Placed on Stable Surface. | Check the plug and ensure the power cord is securely connected. Place the heater on a flat, stable surface. |
| Not Functioning, All Indicator Lights Flashing | Overheating Protection Activated Due to High Body Temperature. | Ensure the air inlet and outlet are unobstructed, allow the heater to cool down, and then restart it. |
| Unusual Noise When Moved or Shaken | Noise from Tip-over Protection Switch Ball. | Normal Occurrence: Avoid vigorously shaking the heater. |
If the above issues cannot be resolved, please contact customer support.
10 WARRANTY
Thank you for choosing Homerunpet Pet-Friendly Space Heater. Please read the instructions below carefully before using.
Homerunpet offers a one-year limited warranty from the original date of purchase. Homerunpet requires presentation of the original proof of purchase to ascertain the date.
Replacement products or repaired parts will be warranted only for the unexpired portion of the original warranty. This warranty is valid only under normal operating conditions for which the unit is intended.
This limited warranty does not apply to any defect resulting from negligence, accident, misuse, or any other reason beyond Homerunpet's control, including but not limited to: failure to follow the product instructions and service manual, improper or inadequate maintenance, connection to improper power supply, unauthorized product modification, fire, lightning, flood, or other external causes.
The appliance must be maintained in accordance with the instructions. The motor is factory sealed; tampering will void the warranty.
For warranty service and more information, please contact contact@homerunpet.com.
Additional Information
MADE IN CHINA
FABRIQUÉ EN CHINE
MORE INFORMATION
[Facebook Icon] [Instagram Icon] [YouTube Icon]
Note: Social media links are placeholders based on common patterns; actual links may vary. YouTube embed is not possible without a specific video URL.
