Doro 1361 Quick Start Guide

GET STARTED

SIM card, memory card and battery

Remove the battery cover: Be careful not to damage your fingernails when removing the battery cover. Do not bend or twist the battery cover excessively as it may be damaged.

Insert SIM card (required): Remove the battery if it is already installed. There are two SIM card slots, SIM1 and SIM2. It is recommended to use SIM1 if only one SIM card is used. Slide the card under the metal part with the gold-coloured circuit board facing down. The cut-off corner of the card helps with correct placement, indicated in the compartment.

Insert SD card (optional): Press the card's lid carefully towards the assistance button until it clicks. Lift the lid to an upright position. Ensure the card's contacts face downwards. Fold down the lid and carefully push it down, sliding it back into place. Note: The circuit boards on the cards must not be scratched or bent. Avoid touching the circuits with your fingers.

Insert the battery: Slide the battery into the battery compartment with the circuits facing down to the right. Replace the battery cover.

Enter text

Press a numerical key repeatedly until the desired character is shown. Wait a few seconds before entering the next character. Press [*] for a list of special characters. Select the desired character with [scroll up/down] and press [OK] to enter it. Use [scroll left/right] to move the cursor within the text. Press [#] to cycle through upper case, lower case, and numerals. Press and hold [#] to change the writing language.

Change language, time and date

The default language is determined by the SIM card.

Calls

Make a call

1. Enter the phone number. Use [Clear] to delete. 2. Press [call button] to dial. Press [Abort] to cancel the call. 3. Press [end call button] to end the call. Note: For international calls, always use [+] before the country code. Press [*] twice for the international prefix [+].

Call from the phonebook

1. Press [menu button] then [Name] to open the phonebook. 2. Use [scroll up/down] to scroll through the phonebook, or quick search by pressing the key corresponding to the first letter of the name. 3. Press [Options] then [Call], alternatively, press [call button] to dial the selected entry, or press [Back] to return to standby.

Call log

Received, missed, and dialled calls are saved in a combined call log. Up to 20 calls of each type can be stored. For multiple calls to the same number, only the most recent is saved. 1. Press [call log button]. 2. Use [scroll up/down] to scroll through the call log. The icons indicate: [received call icon] = Received call, [dialled call icon] = Dialled call, [missed call icon] = Missed call. 3. Press [call button] to dial, or [Options].

PHONEBOOK

The Phonebook can store 100 entries with up to 3 phone numbers per entry.

Add a contact

1. Press [menu button] → [Phonebook] → [-New contact-] → [Add]. 2. Enter a Name for the contact (use Enter text instructions). Use [Clear] to delete. 3. Use [scroll up/down] to select Mobile, Home, or Office, and enter the phone number(s) including the area code. 4. When done, press [Save].

MESSAGES

Create and send text messages

1. Press [menu button] → [Messages] → [Create new] → [SMS]. 2. Write your message (see Enter text instructions), then press [To]. 3. Select a recipient from [Add from Phonebook]. Alternatively, select [Enter number] to add recipient manually and press [OK]. 4. You can modify recipients by selecting one and pressing [Options] → [Edit/Delete/Delete all]. 5. When done, press [Options] → [Send].

Create and send picture messages

Both sender and recipient need subscriptions supporting picture messages. Settings are usually provided by your service provider. 1. Press [menu button] → [Messages] → [Create new] → [MMS]. 2. Write your message (see Enter text instructions). 3. Press [Options] → [Add picture]: [My pictures] to select a file, or [Take picture] to use the camera. Note: For best quality, send only one picture per message. You can also [Add sound], [Add video], and [Preview MMS] using the [Options] menu. 4. Press [Options] → [Add subject] and enter your subject, then press [Options] → [Done]. Press [Options] → [To] and select recipient from [Add from Phonebook]. Alternatively, select [Enter recipient] to add manually and press [Options] → [Done]. 5. Press [Add] to add more recipients. 6. Press [Options] → [Send] to send.

Settings

Press [menu button] → [Settings] → [Messages].

Charge the phone

CAUTION: Only use batteries, chargers, and accessories approved for this model. Connecting other accessories may be dangerous and invalidate the phone's type approval and guarantee.

When the battery is running low, the [battery low indicator] is displayed and a warning signal is heard.

Connect the mains adapter to the wall socket and to the [charging socket] on the phone. Tip: Don't forget to remove the protective plastic film from the display.

GET TO KNOW YOUR PHONE

Turn the phone on and off

1. Press and hold the [red button / power button] on the phone to turn it on/off. Confirm with [Yes] to power off.

2. If the SIM card is valid but protected with a PIN code, 'Input SIM1 PIN' is displayed. Enter the PIN code and press [OK]. Use [Clear] to delete. Note: If PIN and PUK codes were not provided with your SIM card, contact your service provider. 'Trials remain: #' shows the number of PIN attempts left. When no more attempts remain, 'PIN blocked' is displayed. The SIM card must be unlocked with the PUK code. 1. Enter the PUK code and confirm with [OK]. 2. Enter a new PIN code and confirm with [OK]. 3. Re-enter the new PIN code and confirm with [OK].

Start-up wizard

When starting the telephone for the first time, you can use the start-up wizard to set basic settings. Tip: You can run the start-up wizard later if desired.

Step-by-step instructions

In this document, the [arrow symbol] indicates the next action. To confirm an action, press [OK]. To select an item, scroll or highlight it using [scroll up/down] and then press [OK].

Receive a call

1. Press [call button] to answer, or press [Silent button] to switch off the ring signal and then [Reject] (busy signal). Alternatively, press [reject button] directly to reject the call.

2. Press [end call button] to end the call.

Volume control

Use [scroll up/down] to adjust the sound volume during a call. The volume level is indicated on the display.

Silent

Silent is a profile that disables keypad tones, message tones, and ring tones, while vibration, tasks, and alarms remain active. Press and hold [#] to activate and deactivate silent.

Call options

During a call, the soft keys [left selection button] and [right selection button] provide access to additional functions.

Speed dial

Use [number keys] 0 and 2-9 to speed dial an entry from standby. Press and hold the corresponding button to dial.

Add speed dial numbers

1. Press [menu button] → [Settings] → [Phonebook] → [Speed dial]. 2. Select [0 Add] and choose an entry from the phonebook. 3. Press [OK] to confirm. 4. Repeat to add speed dial entries for buttons 2-9.

SOS calls

As long as the phone is switched on, it is always possible to place an SOS call by entering the main local emergency number for your present location followed by the [SOS button].

ICE (In Case of Emergency)

In the event of a trauma, having this information readily available can increase chances of survival. Add ICE contacts to improve your safety. First responders can access additional information such as medication and next of kin from your phone. All fields are optional, but more information is better. Press [menu button] → [Phonebook] → [ICE]. 5. Use [scroll up/down] to scroll through the list of entries. 6. Press [Edit] to add or edit information in each entry. Use [Clear] to delete. 7. Press [Save] when done.

ASSISTANCE BUTTON

The assistance button provides easy access to contact your predefined help numbers. Ensure the assistance function is activated and configured before use. Test the application thoroughly.

Make an assistance call

1. When help is needed, press and hold the [assistance button] for 3 seconds, or press it twice within 1 second. The assistance call begins after a 5-second delay. During this delay, you can prevent a possible false alarm by pressing [cancel button]. 2. An assistance text message (SMS) is sent to all recipients. The first recipient in the list is dialled. If the call is not answered within 25 seconds, the next number is dialled. Dialling is repeated 3 times or until the call is answered, or until [cancel button] is pressed.

CAUTION: When an assistance call is activated, the phone is pre-set to handsfree mode. Do not hold the device near your ear when handsfree mode is in use, as the volume may be extremely loud.

Settings

Press [menu button] → [Settings] → [Assistance].

CAMERA (TAKE PHOTOS)

1. Press [menu button] → [Camera]. 2. Press [OK] to take the photo. 3. Press [Options] or [Back] to take a new photo (if no selection is made, the picture is saved).

Settings

Press [menu button] → [Settings] → [Camera].

BLUETOOTH®

You can connect wirelessly to other Bluetooth® compatible devices such as headsets or other phones.

Important! When not using Bluetooth connectivity, turn off [Activate] or [Visibility]. Do not pair with an unknown device.

Activate Bluetooth®

1. Press [menu button] → [Settings] → [Bluetooth] → [Activation] → [On]. 2. Press [OK] to confirm.

Search device

1. Press [menu button] → [Settings] → [Bluetooth] → [Search device]. 2. Select a device from the list and press [Bond] to connect. If Bluetooth is not enabled, press [Yes] to activate. 3. Press [OK] to confirm.

SOUND & DISPLAY

Tone setup

1. Press [menu button] → [Settings] → [Sound] → [Tone setup] → [SIM1 incoming call]. 2. Use [scroll up/down] to select one of the available melodies; the melody will play. 3. Press [OK] to confirm or [Back] to discard changes.

Text size

You can customize the text size for the menu and messages. 1. Press [menu button] → [Settings] → [Display] → [Text size]: Choose [Normal] or [Large]. 2. Press [OK] to confirm.

Brightness

You can customize the brightness settings. A higher value provides better contrast. 1. Press [menu button] → [Settings] → [Display] → [Brightness]: Choose [Level 1-3]. 2. Press [OK] to confirm.

ADDITIONAL FUNCTIONS

Alarm

1. Press [menu button] → [Alarm] → [On]. 2. Enter the alarm time using the keypad and press [OK] to confirm. Options include: [Single] for a single occurrence, or [Repeated] for a repeated alarm. Scroll through the list of days and press [On] or [Off] to enable or disable for each day. 3. When done, press [Save]. 4. When the alarm sounds, press [Stop] to turn it off or [Snooze] to repeat the alarm after 9 minutes. Note: The alarm works even when the phone is switched off. Do not power on if wireless phone use is prohibited or may cause interference or danger.

Torch

Slide up to turn on the torch. Slide down to turn off.

Reset settings

1. Press [menu button] → [Settings] → [Security]. 2. Select [Reset settings] to reset phone settings to default. 3. Enter the phone code and press [OK] to reset. Tip: The default phone code is 1234.

Reset all

1. Press [menu button] → [Settings] → [Security]. 2. Select [Reset all] to delete phone settings and content such as contacts, number lists, and messages (SIM memory is not affected). 3. Enter the phone code and press [OK] to reset. Tip: The default phone code is 1234.

TROUBLESHOOTING

Phone cannot be switched on

• Battery charge low: Connect the power adapter and charge the battery.
• Battery incorrectly installed: Check the installation of the battery.

Failure to charge the battery

• Battery or charger damaged: Check the battery and charger.
• Battery recharged in temperatures < 0°C or > 40°C: Improve the charging environment.
• Charger incorrectly connected to phone or power socket: Check the charger connections.

PIN code not accepted

Wrong PIN code entered too many times: Enter the PUK code to change the PIN code, or contact the service provider.

SIM card error

• SIM card damaged: Check the condition of the SIM card. If damaged, contact the service provider.
• SIM card incorrectly installed: Check the installation of the SIM card. Remove and reinstall it.
• SIM card dirty or damp: Wipe the contact surfaces of the SIM card with a clean cloth.

Failure to connect to network

• SIM card invalid: Contact the service provider.
• No coverage of GSM service: Contact the service provider.

Failure to add a contact

Phonebook memory full: Delete contacts to free up memory.

Failure to set a function

Function not supported or subscribed from network: Contact the service provider.

SAFETY INSTRUCTIONS

WARNING: The unit and accessories may contain small parts. Keep all equipment out of the reach of small children. The mains adapter is the disconnect device between the product and mains power. The mains socket outlet must be close to the equipment and easily accessible.

Network services and costs

Your device is approved for use on GSM 850/900/1800/1900 MHz networks. A subscription with a service provider is required. Using network services may incur costs. Some features require network support, which may need a separate subscription.

Operating environment

Follow all applicable rules and laws. Always turn off the unit when its use is prohibited or can cause interference or hazards. Only use the unit in its normal user position. Parts of the unit are magnetic and can attract metal objects. Do not keep credit cards or other magnetic media near the unit, as stored information may be erased.

Medical units

Equipment transmitting radio signals, like mobile phones, can interfere with insufficiently protected medical equipment. Consult a doctor or the equipment manufacturer to determine if it has adequate protection against external radio signals. If health care facilities display notices instructing you to turn off the unit, comply with them. Hospitals and health care facilities may use equipment sensitive to external radio signals.

Implanted medical devices

To avoid potential interference, manufacturers of implanted medical devices recommend a minimum separation of 15 cm between a wireless device and the medical device. Persons with such devices should: Always keep the wireless device more than 15 cm from the medical device. Not carry the wireless device in a breast pocket. Hold the wireless device to the ear opposite the medical device. If you suspect interference, turn the phone off immediately. Consult your health care provider if you have questions about using your wireless device with an implanted medical device.

Areas with explosion risk

Always turn off the unit in areas where there is a risk of explosion. Follow all signs and instructions. This includes areas where you are normally asked to turn off your car engine, as sparks can cause explosion or fire, leading to personal injury or death. Turn off the unit at filling stations, fuel pumps, and auto repair facilities. Follow restrictions for radio equipment use near places where fuel is stored/sold, chemical factories, and blasting sites. Areas with explosion risk are often marked, but not always. This also applies to below decks on ships; transport/storage of chemicals; vehicles using liquid fuel (e.g., propane, butane); and areas where the air contains chemicals or particles like grain, dust, or metal powder.

Li-ion battery

WARNING: This product contains a Li-ion battery. Risk of fire and burns if handled improperly. Danger of explosion if battery is incorrectly replaced. To reduce risk of fire or burns, do not disassemble, crush, puncture, short external contacts, expose to temperatures above 60°C (140°F), or dispose of in fire or water. Recycle or dispose of used batteries according to local regulations or the supplied reference guide.

Protect your hearing

WARNING: Excessive exposure to loud sounds can cause hearing damage. Loud sounds while driving may distract you and cause an accident. Listen to a headset at a moderate level, and do not hold the device near your ear when the loudspeaker is in use.

Emergency calls

Important! Mobile phones use radio signals, the mobile network, the terrestrial network, and user-programmed functions. Connection cannot be guaranteed in all circumstances. Never rely solely on a mobile phone for very important calls, such as medical emergencies.

Vehicles

Radio signals can affect electronic systems in motor vehicles (e.g., electronic fuel injection, ABS brakes, cruise control, airbag systems) if incorrectly installed or inadequately protected. Contact the manufacturer or representative for more information about your vehicle or additional equipment. Do not keep or transport flammable liquids, gases, or explosives with the unit or its accessories. For vehicles with airbags: Airbags deploy with considerable force. Do not place objects, including radio equipment, in the area above the airbag or where it might expand. Serious injuries may result if mobile phone equipment is incorrectly installed and the airbag deploys. It is prohibited to use the unit in flight. Turn off the unit before boarding a plane. Using wireless telecom units on a plane can pose risks to air safety, interfere with telecommunications, and may be illegal.

CARE AND MAINTENANCE

Your unit is a technically advanced product and should be treated with great care. Negligence may void the warranty. Protect the unit from moisture. Rain, snowfall, moisture, and all types of liquid can contain substances that corrode electronic circuits. If the unit gets wet, remove the battery and allow it to dry completely before replacing it. Do not use or keep the unit in dusty, dirty environments, as moving parts and electronic components can be damaged. Do not keep the unit in warm places, as high temperatures can reduce lifespan, damage batteries, and distort or melt plastics. Do not keep the unit in cold places; condensation may form when it warms up, potentially damaging circuits. Do not try to open the unit except as indicated. Do not drop or shake the unit; rough treatment can break circuits and precision mechanics. Do not use strong chemicals to clean the unit. The advice applies to the unit, battery, mains adapter, and accessories. If the phone is not working correctly, contact the place of purchase for service, providing the receipt or invoice copy.

WARRANTY

This product is guaranteed for 24 months from the date of purchase. In case of a fault, contact the place of purchase. Proof of purchase is required for service or support. This guarantee does not apply to faults caused by accident, similar incidents, damage, liquid ingress, negligence, abnormal usage, lack of maintenance, or other user-related circumstances. It also does not apply to faults caused by thunderstorms or voltage fluctuations. Disconnect the charger during thunderstorms as a precaution. Batteries are consumables and not included in the guarantee. This guarantee does not apply if non-Doro original batteries are used. This is a voluntary manufacturer's warranty providing additional rights, not affecting statutory end-user rights.

COPYRIGHT AND OTHER NOTICES

© 2017 Doro AB. All rights reserved. Bluetooth® is a registered trademark of Bluetooth SIG, inc. eZiType™ is a trademark of Zi Corporation. vCard is a trademark of the Internet Mail Consortium. microSD is a trademark of SD Card Association.

The contents of this document are provided "as is". Doro reserves the right to revise this document or withdraw it at any time without prior notice. Other product and company names mentioned herein may be trademarks of their respective owners. Doro is not responsible for the functionality, content, or end-user support of third-party apps provided with your device.

Content copyright

Unauthorized copying of copyrighted materials is contrary to copyright laws. This device is intended solely for copying non-copyrighted materials, materials you own the copyright to, or materials you are legally permitted to copy. If uncertain about your right to copy material, contact your legal advisor.

TECHNICAL DATA

Specifications

Specific Absorption Rate (SAR)

This device meets applicable international safety requirements for exposure to radio waves. Your mobile device is a radio transmitter and receiver designed not to exceed exposure limits recommended by international guidelines. The radio wave exposure guidelines use Specific Absorption Rate (SAR), with a limit of 2 W/kg averaged over 10 grams of tissue, including a safety margin. Tests for SAR are conducted using standard operating positions at the device's highest certified power level. The highest SAR values for this device model are: Head SAR: 0.486 W/kg, Body SAR: 1.670 W/kg. During normal use, SAR values are typically well below stated values due to automatic power reduction. This device meets RF exposure guidelines when used against the head or positioned at least 0.5 cm away from the body. For body-worn operation using a holder, ensure it contains no metal and provides the stated separation distance.

The World Health Organization (WHO) states that current scientific information does not indicate the need for special precautions when using mobile devices. For reduced exposure, reduce usage or use a hands-free accessory to keep the device away from your head and body.

Correct disposal of this product (Waste Electrical & Electronic Equipment)

This marking on the product, accessories, or manual indicates that it and its electronic accessories should not be disposed of with household waste. Separate these items from other waste and recycle them responsibly to promote sustainable reuse of material resources. Household users should contact their retailer or local government office for recycling details. Business users should contact their supplier and check purchase contract terms. This product and its accessories should not be mixed with other commercial waste for disposal. This product is RoHS compliant.

Correct disposal of batteries in this product

The marking on the battery, manual, or packaging indicates that the battery should not be disposed of with household waste. Chemical symbols [mercury symbol] (Hg), [cadmium symbol] (Cd), or [lead symbol] (Pb) indicate the battery contains mercury, cadmium, or lead above specified levels. Improper disposal can harm human health or the environment. To protect natural resources and promote material reuse, separate batteries from other waste and recycle them through your local battery return system.

Declaration of Conformity

Doro declares that the radio equipment type DFB-0120 (Doro 1361) complies with Directives 2014/53/EU and 2011/65/EU. The full text of the EU declaration of conformity is available at: www.doro.com/dofc

Model: DFB-0120 Doro 1361 (3041)

QSG English

QSG_Doro_1361_en_A3(A7)_v10(3041)

www.doro.com