Elo Self-Service Stand Assembly Instructions

Product Identification

Model Numbers:

• E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4
• E797162 ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE

Kit Contents: E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4

This kit includes the Floor-Head Assembly (Qty. 1).

Hardware List:

Panel Hardware:

Kit Contents: E797162 ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE

This kit includes the Floor Base (Qty. 1).

Assembly Steps

Step 1: Assemble Tower to Base

Place the tower onto the floor base. Secure using (4) screws from bag "K".

Step 2: Attach Front Cover

• Remove and save the (4) screws on the left and right of the stand front cover.
• Pull off the silver cover and set aside.
• Add (2) remaining screws from bag "K" to the bottom front of the stand.
• Re-attach the silver cover using the saved screws.

Step 3: Remove Printer Tray

Remove and save (2) screws on the rear of the Head, then pull out the printer tray.

Step 4: Install Power Strip

Note: Power strip shown available from McMaster-Carr, item #7361K43.

• Add power strip brackets (supplied with power strip) using (2) screws from bag "L".
• Hook one side of the power strip onto the brackets, then push to snap down.

Step 5: Secure Power Bricks

Add power bricks into the tower using the provided straps.

Step 6: Mount Display Bracket

• Add (2) screws from bag "A" to the top of the stand head, leaving approximately 3mm (1/8") gap for the Display Bracket.

Step 7: Choose Display Bracket (Android or Windows)

For 15" or 22" monitors, use the appropriate Display Bracket.

• Remove and save (2) screws, open the cover of the Display Bracket; pivot out and fix the prop.

Step 8: Assemble Display Bracket to Head

• Assemble the Display Bracket onto the Head.
• Positioning:
• Position "A" for 15", 22" in landscape.
• Position "B" for 15" in portrait.
• Position "C" for 22" in portrait.
• Add (2) screws from bag "A" at the bottom holes, maintaining the ~3mm gap.

Step 9: Assemble USB Hub

• Assemble the USB Hub.
• Add (2) screws from bag "S"; leave approximately 3mm (1/8") gap for the USB bracket to slide on, then tighten screws.

Step 10: Android Slate - Landscape

Note: EMV Cradles are not compatible with Android Slate in landscape orientation.

• Add (2) screws from bag "L" to the top 75mm VESA positions, leaving approximately 3mm (1/8") gap for mounting to the display bracket.
• Connect the Slate Hub to the Slate and attach the cable cover before proceeding.

Step 11: Mount Android Slate

• Route the Slate Hub through the display bracket and head.
• Mount the Slate, add (2) screws from bag "L" to the bottom 75mm VESA positions.
• Add a tie-wrap as shown. Tighten VESA screws to 12 in-lb (1.4 N-m).

Step 12: Android Slate - Portrait

If using an EMV Cradle, follow those instructions before proceeding.

• Add (2) screws from bag "L" to the top 75mm VESA positions, leaving approximately 3mm (1/8") gap for mounting to the display bracket.
• Attach the Slate Hub and cable cover before mounting the display on the stand.

Step 13: Mount Android Slate (Portrait)

• Route the Slate Hub through the display bracket and head.
• Mount the Slate, add (2) screws from bag "L" to the bottom 75mm VESA positions.
• Add a tie-wrap as shown. Tighten VESA screws to 12 in-lb (1.4 N-m).

Step 14: Attach Slate Hub to Tower

• Apply double-sided foam tape from bag "U" to the back of the Slate Hub.
• Attach the Slate Hub to the back of the tower approximately where shown.
• Route the LAN cable through the tower base.
• Connect the LAN and power supply to the Slate Hub.

Step 15: Android or 15"/22" Monitor - Landscape

Note: EMV Cradles are not compatible with monitors in landscape orientation.

• Add (2) screws from bag "L" to the top 100mm VESA positions, leaving approximately 3mm (1/8") gap for mounting to the display bracket.
• Remove cable cover(s) before mounting the display on the stand.

Step 16: Mount Monitor (Landscape)

• Mount the I-Series monitor.
• Add (2) screws from bag "L" to the bottom 100mm VESA positions.
• Route power and LAN cables through the bottom of the stand head. Route the USB Hub cable or other USB if used.
• Tighten VESA screws to 12 in-lb (1.4 N-m).

Step 17: Android or 15"/22" Monitor - Portrait

If using an EMV Cradle, follow those instructions before proceeding.

• Add (2) screws from bag "L" to the top 75mm VESA positions, leaving approximately 3mm (1/8") gap for mounting to the display bracket.
• Remove cable cover(s) before mounting the display on the stand.

Step 18: Mount Monitor (Portrait)

• Route the Slate Hub through the display bracket and head.
• Mount the I-Series monitor.
• Add (2) screws from bag "L" to the bottom 75mm VESA positions.
• Add a tie-wrap as shown.
• Route power and LAN cables through the bottom of the stand head. Route the USB Hub cable or other USB if used.

Step 19: Optional Backpack 4.0 Installation

• Optional: Mount Backpack 4.0 to the tower bracket as shown using (4) screws from bag "T".
• To improve Wi-Fi signal, use antenna extension cables (Amphenol RF P/N 095-902-538-024, available from Digikey or Mouser).
• Remove antennas from the Backpack, attach (2) extension cables to Backpack antenna connectors.
• Attach the male end of the extension cables to the holes in the tower rear, then attach the antennas to the cable connectors.

Step 20: Windows Landscape

If using an EMV Cradle, follow those instructions before proceeding.

• For 15" monitors: Add (2) screws from bag "M" to the top 75mm VESA positions.
• For 22" monitors: Add (2) screws from bag "N" to the top 75mm VESA positions.
• Leave approximately 3mm (1/8") gap for mounting to the display bracket.
• Route the power cable from the I-Series through the bottom of the stand and through the openings in the mount bracket as shown.

Step 21: Mount Windows Monitor (Landscape)

• Place the I-Series on a surface near the stand head, within reach of the cable.
• Remove cable door (A), plug in the power cable (B), and replace the cable door (C) as shown.
• Mount the I-Series monitor.
• Add (2) screws from bag "M" (for 15") or bag "N" (for 22") to the bottom 75mm VESA positions.
• Route the LAN cable through the bottom of the stand head. Route the USB Hub cable or other USB if used.

Step 22: Windows Portrait

If using an EMV Cradle, follow those instructions before proceeding.

• For 15" monitors: Add (2) screws from bag "M" to the top 75mm VESA positions.
• For 22" monitors: Add (2) screws from bag "N" to the top 100mm VESA positions.
• Leave approximately 3mm (1/8") gap for mounting to the display bracket.
• Route the power cable from the I-series through the bottom of the stand and through the openings in the mount bracket as shown.

Step 23: Mount Windows Monitor (Portrait)

• Place the I-Series on a surface near the stand head, within reach of the cable.
• Remove cable door (A), plug in the power cable (B), and replace the cable door (C) as shown.
• Mount the I-Series monitor.
• Add (2) screws from bag "M" (for 15") or bag "N" (for 22") to the bottom 75mm VESA positions.
• Route the LAN cable through the bottom of the stand head. Route the USB Hub cable or other USB if used.

Step 24: Printer Installation

• If using a printer, remove the cover to add the printer.
• For Star printers:
• Add (2) screws from bag "C" to the printer tray; use the Star printer bracket to set the depth of the screws, then remove the Star bracket.
• Add the Star printer with bracket to the printer tray. Secure the printer to the printer tray using the third screw from bag "C".
• For Epson TM-T88:
• Add (4) screws from bag "D" to attach the printer to the tray.
• Route cables from/to the printer as needed.
• Slide in the printer tray assembly (or printer tray with cover if no printer).

Step 25: Final Assembly

• Close the Display Bracket and add the (2) screws saved from Step 7.
• Secure the printer assembly with the (2) screws saved from Step 3.

Step 26: Attach Floor Stand Cover

• Replace the floor stand cover and secure using the (4) screws saved from Step 2.

Step 27: Secure Stand to Floor

• There are (2) bolt holes available on the top of the base to secure the stand to the floor.
• The feet can be adjusted in case of uneven surfaces.

Step 28: EMV Cradle Installation (Optional)

• If installing an EMV Cradle with the display in landscape orientation, finish by adding (1) screw from bag "S".

Contact Information & Legal

Learn more about Elo at EloTouch.com.

The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.

Elo, the Elo logo and Wallaby are either trademarks or registered trademarks of Elo Touch Solutions, Inc.