ASUS TUF Gaming GT301 User Manual

Accessory Kit Contents

The following accessories are included in the kit:

• A: PSU / 3.5" Drive Screws (x8)
• B: Motherboard / 2.5" Drive Screws (x25)
• C: Standoff Tool (x1)
• D: Cable Ties (x8)
• E: Headphone Hanger (x1)
• F: Headphone Hanger Screw (x1)
• G: VGA Holder Rubbers (x2)
• H: Velcro Strap (x3)

Installation Guide

1. Remove the Side Panels

   Step 1: Unscrew and remove the side panels. A screwdriver is required. Handle with care, especially if panels are glass.

   Step 2: The case is now ready for further component installation after side panels are removed.

2. Install the Power Supply Unit (PSU)

   Step 1: Insert the PSU into its designated bay.

   Step 2: Secure the PSU using four (4) Type A screws.

3. Install the Cooler & RAM on the Motherboard

   Step 1: Install the CPU cooler onto the motherboard. Ensure it is properly seated.

   Step 2: Install the RAM modules into the appropriate slots on the motherboard.

4. Install the I/O Shield

   Insert the I/O shield into the rectangular cutout at the rear of the case, ensuring it snaps into place.

5. Install the Motherboard Unit

   Step 1: Place the motherboard into the case, aligning it with the standoffs. Secure the motherboard using nine (9) Type B screws.

   Step 2: Ensure the motherboard is firmly installed.

6. Attach the Front I/O Connectors

   Connect the front panel I/O connectors (POWER SW, POWER LED-, POWER LED+, RESET, HD AUDIO) to the corresponding headers on the motherboard.

7. Addressable RGB Controller Hub

   Connect the ARGB control to the power supply via SATA. The AURA Sync Control can be connected to the +5V motherboard Addressable RGB header. Optionally, connect to another motherboard +5V header. The controller can also connect to the Front I/O control button.

   Note: The maximum output of the addressable RGB connectors (5V) is 2.6A.

   Controls:

   • Turn On: Press the LED button if the fan LEDs are off.
   • Turn Off: Press the LED button for 3 seconds.
   • Default: Rainbow pattern.
   • Multi-pattern Change: Press the LED button for 0.5 seconds.
   • AURA Sync (Change to MB Mode): Press the LED button for 5 seconds. The fan LED will turn off, then blink Green 2 times rapidly. MB Mode only works when the control board is connected to the motherboard's Addressable RGB header. Compatible with AURA Sync.

8. Install the PCI-E Card

   Step 1: Identify the correct PCI-E slot on the motherboard.

   Step 2: Remove the corresponding expansion slot cover from the back of the case.

   Step 3: Insert the PCI-E card into the slot, ensuring it is fully seated.

   Step 4: Secure the card using either Type G VGA Holder Rubbers or screws.

   Step 5: Ensure the PCI-E card is securely installed.

9. Install the 2.5" Drives

   Step 1: Attach the drive bracket to the case using Type B screws.

   Step 2: Mount the 2.5" drive onto the bracket.

   Step 3: Secure the drive to the bracket.

10. Install the 3.5" / 2.5" Drives

    Step 1: Mount the drive into the appropriate cage using Type A screws (for 3.5" drives) or Type B screws (for 2.5" drives).

    Step 2: Slide the drive cage into the case and secure it.

11. Installation and Maintenance of the Dust Filters

    Step 1: Locate the dust filters, typically at the front and bottom of the case.

    Step 2: Slide the dust filters out for cleaning or replacement.

12. Install the Headphone Hanger

    Step 1: Attach the headphone hanger to the designated mounting point on the case using the provided screws.

    Step 2 & 3: Secure the hanger firmly.

Additional Information

CPU Cooler Height Limitation

The maximum CPU cooler height supported is 160 mm.

A diagram illustrates a PC case with a shaded area indicating the maximum height for a CPU cooler.

Graphics Card Limitation

The maximum graphics card length supported is 320 mm.

A diagram shows a PC case with a shaded area indicating the maximum length for a graphics card.

Fan Setup Compatibility

The case supports the following fan configurations:

• 120 mm fans x 6
• 140 mm fans x 2

Water-cooling Radiator Options

The case supports various water-cooling radiator sizes, including:

• 120 mm
• 140 mm
• 240 mm
• 280 mm
• 360 mm

Safety Information

Please refer to the safety information section for important guidelines regarding the use and handling of the computer case and its components.

ASUS Recycling/Takeback Services

ASUS is committed to environmental protection and offers recycling and takeback programs for its products, batteries, components, and packaging materials. For detailed recycling information by region, please visit http://csr.asus.com/english/Takeback.htm.

Australia statement notice

From January 1, 2012, updated warranties apply to all ASUS products, consistent with the Australian Consumer Law. For the latest product warranty details, visit https://www.asus.com/support/. ASUS products come with guarantees that cannot be excluded under the Australian Consumer Law. For assistance, contact ASUS Customer Service at 1300 2787 88 or visit https://www.asus.com/support/.

India RoHS

This product complies with the "India E-Waste (Management) Rules, 2016". It prohibits the use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs), and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01% by weight in homogenous materials for cadmium, except for exemptions listed in Schedule II of the Rule.

REACH

In compliance with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, ASUS publishes the chemical substances in its products on the ASUS REACH website: http://csr.asus.com/english/REACH.htm.

The document also includes statements regarding REACH compliance in various languages including Traditional Chinese, Simplified Chinese, Czech, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Swedish, and Turkish.

A table indicates the presence of hazardous substances in different components of the case, with 'X' denoting levels exceeding regulatory limits and 'O' denoting compliance.

The product is compliant with AEEE regulations.