Ice Makers User Manual

Chapter 01: Safety Warnings

1. Always plug in your product to a grounded power outlet.
2. Your ice maker is designed to operate at the voltage shown on the Technical Table. Running the product at a different voltage may cause the product to become dysfunctional or even may cause fire.
3. Do not place your ice maker next to any heat source.
4. Set up your ice maker at a humidity-free location and with unobstructed air circulation around the unit.
5. After the installation is done, do not move your ice maker and wait for at least two hours to start it.
6. Make sure you have cleaned the inside surface of your product before first use.
7. Do not use power strips or extension cords to run your product.
8. Protect the power cord against hot surfaces.
9. Do not let untrained and/or unsupervised children younger than 8 years old operate your ice maker.
10. The cleaning and maintenance of the device should not be made by children unless they are under supervision.

Chapter 02: General Outlook and Technical Specifications

Small differences in color and other variations are possible for different visualization, imaging technologies, or other technical reasons. The manufacturer is not liable for these differences and deviations. No rights can be obtained due to typographical errors, product descriptions, or obvious errors on the website. Adjustable legs can vary according to product models.

Technical Table

[Information] (*) Indicates the daily ice making capacity of the product at 20 °C Ambient and 10 °C Water Inlet temperature.

[Information] (**) Check the values of the electrical network to which the product is connected.

Chapter 03: Installation of Ice Maker

Selection of Location for Your Product

[Information] Your product should not be in direct contact with or in close proximity to any heat source.

• You should leave at least 10 cm of distance if you place your ice maker next to other electrical equipment (such as ovens, computers etc.) that are considered as heat sources.
• If the product is to be placed next to a wall, the distance between the back surface of the product and the wall should not be less than 20 cm.
• Do not place objects in front of the ventilation filter of your ice maker that might prevent air circulation into your product.
• Do not place your product outdoors. This product is designed to be used indoors.

Electrical Connection

• The voltage and frequency values of the main power supply have to be the same as written on the product label. If you are in doubt or need assistance, please contact the nearest Authorized Service or get help from a qualified electrician.
• Make sure your power outlet has been grounded.
• The amperage of the circuit breaker to which the product will be plugged in should be 10A**. (See Technical Table / Entry fuse section.)
• Do not use power strips with multi sockets or extension cords to operate your product.

Water Use and Connection

Your ice maker is designed to make ice cubes within the most ideal time and size. However, it is important to note that there are some things that will affect the quality of the ice produced by the machine, as well as the health of the internal components of the ice maker.

The Water Supply

• [Checkmark] Should be good for human consumption,
• [Checkmark] Should have an optimum level of hardness,
• [Checkmark] Should include minimal amount of chlorine.

[Information] The optimum water filters to be used on your product are available and can be purchased from your Authorized Service. Water temperature should be between 10°C and 30°C.

Installation

• Remove and disassemble all packaging materials of the product before installation.
• The ice slide grate, waterproofing plastics, and the ice scoop are provided inside the product. If any part or accessory is missing, please contact customer services.
• Clean the inner cabinet with warm water and a soft cloth before using the ice maker. Clean the ice trays with warm soapy water. Dry with a soft, cotton cloth.
• After placing the ice maker at the installation point, wait 2 (two) hours before operating to get the cooling system pressure stabilized. Install the parts inside the ice maker in accordance with the assembly instructions.
• The cold water inlet pressure must not exceed the operating water pressure (5 Bar) indicated on the technical data sheet. If the line pressure is higher than 5 Bar, a pressure reducer must be installed.
• Connect your device to the mono phase - grounded power supply of the rating indicated on the nameplate. Your device is designed to function normally within ± 10% of the main voltage. If this range cannot be provided in your local power network, it is recommended to use a voltage regulator.
• If it is necessary to change the location of your ice maker, be sure to transport the unit according to the markings on the original packaging of the device.
• Protect your device against factors that may damage the package and the device (moisture, water, impact, chemical, etc.).
• Only Authorized Service should disassemble the device. Never interfere with the internal parts and elements of the ice-maker.
• The device must be commissioned by the Authorized Service.
• Failure to comply with the above conditions will void your product warranty.
• Do not leave packaging materials (plastic bags, nylon, etc.) within the reach of children.
• The manufacturer reserves the right to change the information in this manual. Therefore, this booklet does not constitute a commitment to specifications.

Chapter 04: Use of the Ice Maker

Operating the Ice Maker

After installing your Ice Maker following the instructions above and making all necessary connections:

1. Make sure that the power outlet you are using for your ice-maker is live and has power.
2. Turn on the water.
3. Set the On-Off button at the front of your product to the On position. (When you set it to the On position, the power light on the button will turn on.)
4. The product will automatically go into a delay-time mode for 1 minute after it is turned on.
5. At the end of the delay-time mode, the product will start getting water and making ice.
6. Your product will complete the ice-making cycle after a certain time, depending on the ambient and water temperature.
7. To change the dimple size of the ice made by the ice maker, adjust the potentiometer in the direction of the arrow.

Shutting Off The Ice Maker

• Set the power button at the front of your Ice Maker to "Off" position.
• Unplug the product if you are not going to use the ice-maker for a long time.
• Turn off the water.

Malfunction and Warning Signals (Red Light on Power Button)

Chapter 05: Cleaning and Maintenance of Your Ice Maker

Exterior Cleaning of the Ice Maker

The exterior of your ice-maker is made of stainless steel. Wipe the exterior surfaces with a cotton damp cloth or a sponge and then wipe it with a dry, clean cotton cloth.

Cleaning of the Sprayer System

1. Make sure the water and electrical connections of the product are off, in compliance with the cleaning instructions above.
2. Remove all the ice from the storage bin.
3. The power switch should be off, and the water inlet valve should be opened.
4. Remove the slide grate located inside the inner basin and then remove the level discharge plastic from its slot, and ensure the water to be discharged.
5. Place the water level drain plastic group back to its slot after discharging the water inside the pool.
6. Then, pour the cleaning solution recommended by Authorized Service into the water pool.
7. Select the ‘cleaning’ setting on your product, then turn the power switch to the "On" position. WITHIN 30 SEC OF TURNING ON THE POWER, YOU MUST PRESS AND HOLD THE ‘CLEANING' BUTTON FOR 9 SEC.
8. The cleaning process will continue for 10 minutes.
9. At the end of the cleaning cycle, remove all the produced ice from storage bin.

[Checkmark] Do not turn off the product while cleaning is in progress.

[Checkmark] After the cleaning process, discharge the water inside the inner basin.

[Checkmark] Right after this cleaning, the Ice Set must be cleaned.

Cleaning of the Ice Set

To remove the top cover, remove the screws in "Figure-6". Remove the plastic cover on the cooling pipes. Clean the cooling pipes and visible surfaces in the tank with cleaning solution / soapy cloth. Then rinse and then dry. Close the plastic cover that protects the cooling system pipes and then close the top cover of the product. Then replace the screws.

Cleaning of the Ice Storage Bin

1. To clean the ice bin, first turn the power switch to the “Off” position. Then disconnect the product from the main power supply.
2. Drain the ice completely from the ice bin.
3. Wipe the inside of the ice bin with cleaning solution / soapy cloth and then rinse / dry.
4. Take care not to allow any lime and/or cleaning solution residue to remain.

Cleaning of the Water Inlet Filter

1. Disconnect the Ice Maker from main power supply.
2. Disconnect the water connection of your ice maker.
3. Remove the water inlet filter. (The frequency of cartridge replacement varies depending on the usage period, but it is recommended to change every 6 months.)
4. Follow the filter manufacturer's maintenance and cleaning instructions / recommendations to perform cleaning and maintenance of the water inlet filter.

Then return the Ice Maker to operation by following the installation instructions.

The applications specified in the product cleaning instructions should be performed at least 4-5 times a year.

Chapter 06: Troubleshooting

Actions to be Taken Before Calling Authorized Service

Chapter 07: Scope of Warranty

This warranty provided by the company does not cover the repair of defects caused by unusual use of the ice maker. The following items are excluded from the warranty:

• Malfunctions and damages caused by the operator during use.
• Malfunctions and damages that occurred during shipment or during loading or unloading and during delivery to the end-user.
• Malfunctions and damages that occurred due to low or high voltage, usage contrary to the voltage written on the label of the product and the electrical installation.
• Malfunctions and damages that occurred after any fire or lightning during use.
• Malfunctions resulting from use of the product contrary to the warnings and methods specified in the user manual.

The repairing of the above-mentioned malfunctions shall not be included in the scope of the warranty; the repair shall be charged.

The shipment to the place of use and the assembly of the product are excluded from the product price.

The responsibility for confirming and granting Warranty Certificate to the consumer shall belong to the seller, reseller, agency, or representation from which the consumer bought the good.

The warranty is valid for the period mentioned in the warranty certificate and only for the malfunctions that occurred in the product; no other claims, for a refund, repair, or replacement shall be done. In the case that any destruction/falsification of the original serial number recorded on the warranty certificate and on the product is found, the product shall be out of warranty. As for the repairs within the scope of the warranty, only the services specified in the warranty certificate or on the website are authorized.

Measuring the Mains Water Supply Hardness and Use of Water Filter

[Information] Use of test paper:

• Dip the test paper into the mains water for 1 second.
• Take the paper out of the water and shake.
• Compare what you see on the paper with the color scale.
• Consider our recommendations on the use of filter according to the hardness table.

[Information] Water Hardness and Filter Usage: The hardness is directly proportional to the lime the water contains. As the hardness increases, the amount of lime increases. The lime in the water is inconvenient for the proper functioning of your Ice Maker. In case of non-usage of a filter, it can cause very frequent maintenances and malfunctions that might require repairs out of warranty even in the waters that can be classified as soft.

Filter Usage Notes:

• (*) Use of filter is not required.
• (**) Use of filter is recommended for the life of your Ice Maker.
• (***) Filter has to be used.
• (1) Should not be operated without filter.

NOTE:

The blank pages are for notes.