What's Included?
Thank you for purchasing the AUSDOM Wireless headset.
The package contains:
- AUSDOM Voipfocus Connect Mono Wireless Headset
- USB-C Charging Cable
- USB-A to USB-C Converter
- Carry Bag
- User Manual
- Quick Start Guide
Product Overview
The headset features the following components:
- Volume - Button
- Volume + Button
- LED Indicator
- USB-C Port
- Power/Bluetooth Button
- Microphone Boom
- Mute Button
Diagram Description: An illustration shows the headset with callouts pointing to each of the listed components.
Charging
Ensure the USB-C charging port or the converter is dry before charging.
Use a certified USB-C charging cable and charger or a computer for charging.
It is recommended to fully charge the headset before the first use.
Charging via Headset's USB-C Port:
- Connect the headset to a power supply using the USB-C charging cable.
- Power supply can be a charger or a computer's USB output port. The included USB-A to USB-C Converter allows compatibility with USB-A chargers.
- The LED indicator on the Power/Bluetooth Button shows a steady red light while charging and turns off when fully charged.
Diagram Description: An illustration shows the headset connected via a USB-C cable to a USB-A to USB-C converter, which is plugged into a laptop for power.
Battery Status
When the battery power drops below 5%, the LED indicator on the headset will flash red twice, and a voice prompt "Battery low" will be heard every 3 minutes.
Wearing the Headset
Wear the headset with the microphone boom positioned on either side. Adjust the microphone boom so it is close to your mouth for optimal voice capture.
Tips: When switching the microphone boom to the other side, ensure it is lowered completely and directed towards your mouth. This adjustment also affects the volume control direction and sound channels.
Diagram Description: An illustration shows the headset being worn correctly, with the microphone boom positioned near the user's mouth.
Power On/Off
- Power On: Press and hold the power button for 2 seconds. The LED indicator will turn green for 1 second.
- Power Off: Press and hold the power button for 4 seconds. The LED indicator will turn red for 1 second.
Bluetooth Pairing
Initial Pairing: When the headset is off, press and hold the power button for 4 seconds to enter Bluetooth pairing mode. The LED indicator will flash green and red.
On your device, select "AUSDOM Voipfocus Connect" from the Bluetooth list to connect.
Once connected, the LED indicator will turn solid green.
Diagram Description: Visuals show the LED indicator states: flashing green and red for pairing, and solid green for connected. It also illustrates connecting to a smartphone and a PC.
Pairing with Two Devices:
To pair with a second device while already connected to one:
- Turn off Bluetooth on the first device.
- The headset will automatically enter pairing mode (LED flashes green and red).
- Connect to the second device.
- Turn on Bluetooth on the first device and manually reconnect the headset.
The headset will automatically connect to the last two paired devices when powered on.
Controls
| Button/Operation | Function |
|---|---|
| Power/Bluetooth Button Press and hold for 2 seconds (when powered off) | Power on |
| Press and hold for 4 seconds (when powered on) | Power off |
| Press once | Play/Pause music |
| Press once (when calls incoming) | Answer/End call |
| Press and hold for 2 seconds (when calls incoming) | Reject call |
| Press twice | Last number recall |
| Press and hold for 4 seconds (when powered off) | Repairing mode |
| Volume +/- Buttons Press once (Volume +) | Volume up |
| Press once (Volume -) | Volume down |
| Press and hold Volume + for 2 seconds | Next track |
| Press and hold Volume - for 2 seconds | Previous track |
| Mute Button Press once | Mute microphone |
| Press once | Mute off |
Specifications
| Parameter | Specification |
|---|---|
| Input | 5V ⎓ 0.5A |
| Charging time | 1 hour 30 minutes |
| Playtime | 50 hours |
| Talk time | 32 hours |
| Battery capacity | 400mAh |
| Driver size | 30 mm |
| Microphones | Microphone boom with 2 mics |
| Impedance | 32 Ω |
| Frequency response | 20 Hz - 20 kHz |
| Bluetooth version | V5.1 |
| Bluetooth range | 10 m / 33 ft |
Note: Features and technical specifications are subject to change without prior notice.
Safety & Compliance
Important Safety Information
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO RECYCLING INSTRUCTIONS.
This product is marked with the selective sorting symbol for Waste Electrical and Electronic Equipment (WEEE). This indicates that the product must be handled according to European Directive 2012/19/EU for recycling or dismantling to minimize environmental impact.
Users can choose to return their product to a competent recycling organization or to the retailer when purchasing new electrical or electronic equipment.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Logos Description: CE, FC, RoHS certification marks are displayed.
Warranty Card
ATTENTION:
- Please read the return procedures and warranty policy carefully on www.ausdom.com before sending items back to the point-of-purchase.
- Please fill out this card and send it to your reseller along with the product if your product's warranty is valid.
| S.N: | |
| Date of Purchase: | |
| Product Model: | |
| RMA Number: | |
| Return Reason: | |
| Customer Name: | |
| TEL: | |
| E-mail: | |
| Address: |
For more information, please visit our official website www.ausdom.com.
Your valuable comments and suggestions on improving AUSDOM products are welcome!
Contact: support@ausdom.com, sales@ausdom.com
Brand Logo Description: The AUSDOM logo and tagline "Enjoy Smart Life" are displayed.
Document Version: 220125.V01
