Winix Air Purifier

Front Panel Overview

The front panel features an Air Outlet Vent, a Handle, and a Smart Sensor.

Package Contents

• 360° All-in-One True HEPA Filter
• User Manual
• Wi-Fi Setup Guide

Where to Use

For optimal performance and to prevent malfunction:

• Maintain 12-18 inches (approx. 30-45 cm) of space between the unit and other electronics (e.g., TVs, radios, humidifiers) to avoid electromagnetic interference.
• Place indoors away from direct sunlight to prevent product malfunction or failure.
• Position on hard, flat surfaces only; flimsy or slanted surfaces may cause abnormal noise and vibrations.
• Allow 12-18 inches (approx. 30-45 cm) of space from walls for maximum airflow.

4-Stage Air Purification

Air purification removes inanimate particles through the following stages:

1. Fine Mesh Pre-Filter
2. True HEPA Filter
3. Activated Carbon Filter
4. PlasmaWave Technology

Initial Operation

1. Turn the product upside down.
2. Grab the handle, turn counter-clockwise, and pull out the filter cover.
3. Remove the protective vinyl from the installed filter.
4. Install the filter (top side down) into the bottom of the unit until fully inserted. The top of the filter shows the opening, and the bottom is solid.
5. Turn the handle clockwise to close the filter cover.
6. Return the product to an upright position for normal operation.

Maintenance

When to Replace Filters

The Check Filter indicator LED signals when to replace the HEPA filter. Replacement intervals may vary based on the environment.

Resetting Filter Life

After replacing the filter, with the unit on, press and hold the Filter Reset Button for at least 5 seconds until a beep is heard. The Filter Replacement Indicator will then disappear.

Air Quality Indicator Guide

The numerical pollution level displayed may differ from official sources due to indoor environment or product location.

Control Panel

01. Filter Life / Filter Reset Button

Press briefly to view remaining filter life (F99 ~ F00). Press and hold for 10 seconds to reset the filter life indicator (resets to 100%). Use when replacing filters; can be used when the unit is off.

02. Light Mode Button

Adjusts display brightness (100% ➔ 70% ➔ 30% ➔ OFF).

03. Fan Speed Indicator Buttons

Indicates current fan speed. Use arrow buttons to cycle through speeds: Auto, Low, Medium, High, Turbo.

04. Auto Mode Button

Defaults to Auto with PlasmaWave enabled. Automatically adjusts fan speed based on air quality (Low for good, Medium for fair, High for poor).

05. Power Button

Turns the unit on or off. The Air Quality Indicator cycles through colors for the first 30 seconds as the Smart Sensor detects air quality.

06. Light Sensor

Detects ambient light. In Auto Mode, it determines when to activate Sleep Mode.

07. Wi-Fi / Pairing Button

Press briefly to toggle Wi-Fi on/off. Press and hold for 3 seconds to activate pairing mode. A Wi-Fi indicator appears when active.

08. Air Quality Indicator

Color-coded LED shows air quality: Red (Poor), Amber (Fair), Green (Average), Blue (Good).

09. PlasmaWave® Button

Enables or disables PlasmaWave®. A chirping/buzzing sound during operation is normal and indicates particles passing through PlasmaWave®.

10. Mode Indicator

Shows if Auto & Fan Speed Mode is enabled/disabled.

11. Sleep Mode Indicator

Shows if Sleep Mode is enabled/disabled.

12. Wi-Fi Indicator

Shows if Wi-Fi Mode is enabled/disabled.

13. PlasmaWave® Indicator

Shows if PlasmaWave® is enabled/disabled.

14. Filter Replacement Indicator

LED light indicates when it's time to change the filter.

15. Ultrafine Dust Density Indicator

LED displays air quality. The numeric Smart Sensor measures fine particles down to 2.5 microns.

Cleaning & Care

Cleaning the Filters

Clean the Pre-Filter with a vacuum or soft brush. The Pre-Filter cannot be washed. Cleaning intervals depend on air quality.

Cleaning the Exterior & Interior

Wipe the exterior with a soft, damp cloth using room temperature water, then dry with a clean cloth. After turning the unit upside down, remove the filter cover and vacuum the interior. Clean every 14 days for optimal performance.

How to Disassemble and Clean the Smart Sensor Cover

1. Use a finger to detach the dust sensor cover.
2. Clean the lens and suction port of the dust sensor with a cotton swab, then use a dry cotton swab. (Clean every two months).
3. Close the dust sensor cover until it clicks.

? NOTICE: Do not clean the sensor with volatile substances like water, alcohol, or acetone. Regular cleaning is necessary for optimal sensor performance.

Unit Specifications

Exterior, design, and specifications are subject to change without prior notice to improve performance.

Contact Winix

For product inquiries and customer service:

• ? Dedicated Call Center: (877) 699-4649
• ? Website: www.winixamerica.com

To expedite service, please provide the model name and number, nature of the problem, contact information, and address.

Safety and Cautions

⚠️ WARNING: Read and follow all safety instructions to reduce the risk of injury, electric shock, or fire.

• Ensure filters are installed before operation.
• Do not insert foreign objects into vents.
• Do not touch interior parts with wet hands.
• Ensure intake and outlet vents are not blocked.
• Do not use as a step stool or place heavy objects on the unit.
• Install filters correctly when handling the unit upside down.
• If the power cord is damaged, it must be replaced by the manufacturer or service agent.
• This appliance is not intended for use by persons with reduced capabilities unless supervised.
• Supervise children to ensure they do not play with the appliance.
• Do not use for document or art conservation.
• Do not pull on the power cord when unplugging.
• Do not tie or knot the power cord during operation.
• If the unit is submerged in water, unplug and contact customer service.
• Do not unplug or move the unit while in operation.
• Do not plug additional appliances into the same outlet.
• Do not touch the plug with wet hands.
• Unplug when not in use for extended periods.
• Do not place near heating elements, mist, fumes, or metallic dust.
• Avoid forcefully bending, pulling, twisting, bundling, pinching, or placing heavy objects on the power cord.
• Do not install in motor vehicles or transport vehicles.
• Do not place in areas with excessive noxious gases or flammable materials.
• Do not face the unit into wind or drafts.
• Do not place below an electrical outlet.
• Do not place in excessively humid areas.
• Do not use with solid-state speed control devices.
• Do not place unit closer than 12 inches from the wall to prevent condensation.
• Condensation may occur during winter delivery/installation; this is temporary and will disappear after 1-2 hours of operation.
• The minimum displayed dust concentration is 5 µg/m³.

Limited Warranty

This product comes with a Two (2) Year limited warranty valid in the USA and Canada.

Warranty Terms:

• Product failure due to negligence or misuse voids the warranty.
• Proof of purchase is required for warranty claims.
• Register your product on winixamerica.com to upload proof of purchase.
• For more information, visit winixamerica.com/terms-and-conditions/.

Regulatory Compliance

FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. It generates, uses, and can radiate radio frequency energy. If it causes harmful interference, try reorienting the antenna, increasing separation, or connecting to a different circuit. Consult a dealer or technician for help.

Innovation, Science and Economic Development Canada Compliance: This device contains license-exempt transmitters/receivers compliant with applicable RSS standards. Operation is subject to two conditions: the device may not cause interference, and it must accept any interference, including that which may cause undesired operation.

French Translation: L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement Économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : L'appareil ne doit pas produire de brouillage; L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model's CADR for smoke and the electrical energy it consumes, or CADR/Watt.