ENGO Controls - Heating control
User Guide for ENGO CONTROLS models including: ECAM-SOLAR, ECAM-SOLAR Wi-Fi Smart Solar Camera, Wi-Fi Smart Solar Camera, Smart Solar Camera, Solar Camera, Camera
Designed for outdoor installation, the ECAM-. SOLAR camera features IP65 waterproofing, ensuring it can withstand rain, dust and other adverse weather ...
File Info : application/pdf, 2 Pages, 2.26MB
DocumentDocumentCAM Introduction Camera description The ECAM-SOLAR camera is the ideal solution for outdoor 3 ECAM-SOLAR | Wi-Fi Smart Solar Camera surveillance, combining reliability, convenience and eco- 2 friendliness. With a built-in 5200mAh Li-Ion battery 4 and solar panel included, the camera can operate 100% wirelessly, eliminating the need for any wiring. It is ideal 1 5 for locations where it is difficult to access a permanent power source. Designed for outdoor installation, the ECAM- 6 SOLAR camera features IP65 waterproofing, ensuring it can withstand rain, dust and other adverse weather conditions. 7 Quick Guide Ver. 1.2 Release date: I 2025 Soft: V1.40.145 Works with Powered By GET IT ON Available on the Producer: Engo Controls sp. z o.o. sp. k. Rolna 4 St. 43-262 Kobielice Poland www.engocontrols.com Technical specification Power supply Built-in lithium battery Power supply port USB typ C Communication Wi-Fi 2.4GHz Resolution 4Mpx 2560*1440P Local storage Micro SD(Max 256GB)- card not included Minimum requirements of a microSDXC card -full HD speed class - C10/U1/V10 IP protection class IP65 Dimmension [mm] 125x48x77 Product Compliance This product complies with the following EU Directives: 2014/53/EU, 2011/65/EU. Product features 4Mpx 2560*1440P 2-way audio Motion detection Angle of lance 108° Move tracking Infrared (IR) up to a distance of 10m Safety Information: Use in accordance with national and EU regulations. Use the device only as intended. Installation must be carried out by a qualified person in accordance with national and EU regulations. Installation: Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions. WARNING: For the entire installation, there may be additional protection requirements, which the installer is responsible for (e.g., installation of an additional differential pressure overflow valve). 10 9 11 12 8 13 14 1. Solar panel 2. Light sensor 3. Camera lens 4. Microphone 5. LED diode 6. Loudspeaker 7. Motion sensor 8. Moisture protection 9. Reset button" 10. USB type C power socket 11. Device on/off switch 12. Micro SD slot 13. Locking nut for adjusting the mounting angle 14. Mounting bracket Installation of the camera in the app Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device. STEP1 - DOWNLAD ENGO SMART APP Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone. Powered By STEP 2 - REGISTER THE NEW ACCOUNT To register a new account, please follow the steps below: 1 2 Click,,Sign Up"to create Enter your e-mail new account. address to which the verification code will be sent. 3 4 Enter the verification code received in the email. Remember that you only have 60 seconds toenter the code! Then set the login password. STEP 3 - CONNECT CAMERA TO WI-FI After installing the app and creating an account: 1 2 CONNECT CAMERA TO WI-FI 5 6 CONNECT CAMERA TO WI-FI 11 12 On your mobile device, make sure the ENGO Smart has access to permissions (Location, Bluetooth, Nearby devices). Then turn on Bluetooth and Location. Connect to 2.4GHz Wi-Fi network to which you want to assign the device. Make sure the camera is powered on. Then press and hold the button on the back of the camera for approximately 8 seconds, until the beep. The red LED on the front of the unit will then start flashing. The pairing mode is enabled. 3 4 In the app, select:,,Add Device". Select,,Camera & Lock". Find and click on the Wi-Fi camera in the device list. Then go,,Next". 7 8 Follow the instructions displayed on the smartphone screen. 9 10 Then go,,Next". Select the Wi-Fi network in which the camera will operate and enter the password of this network. Point the camera at the QR code Wait for the app to configure the device with displayed in the app, click ,,I heard the the selected Wi-Fi network. sound" after the beep. 13 14 Go ,,Done". The camera has been installed and displays the main interface. Factory reset To restore the default settings of the camera, hold down the Reset button for about 8 seconds until a beep sounds. Then release the button. The camera will restart, restore the default (factory) settings and be ready to be added to the application again.