Owner's Manual for BOKE models including: BK-DLL042, BK-DLL052, BK-DLL042 Dimmable LED Driver, Dimmable LED Driver, LED Driver, Driver
Dimmable LED driver(DALI-2 pushDIM 1~10V) DLL series - BOKE
info@bokedriver.com www .bokedrivercom Functions Output short-circuit behaviour - In case of a short-circuit at the LED output ,the LED output is switched off. - After restart of the LED driver ,the output will be activated again. Output no-load operation - The LED driver will not be damaged in no-load operation.
File Info : application/pdf, 17 Pages, 2.82MB
DocumentDocumentBOKE Drivers Co.,Ltd. Constantcurrentindependentdimmabledriver DLLSeriessuffixDB(DALI-2+pushDIM+1-10V/10VPWM/Rx+EL+CLO+corridorDIM+ DALIPROG+Wielandquickinstallconnector) Features - Support DALI-2+pushDIM+1-10V /10V PWM+100K potentiometer dimming mode - Support advanced functions such as corridorDIM,EL, CLO - The output current programming configuration of the driver can be realized through the DALI interface - The output interface is Wieland (gesis) pluggable quick connector - 16-level current output can be realized by DIP-switch - Flicker-free output,which meets the requirement of flicker-free standard - Using HPC patented technology, at any dimming level, the brightness of the lights is the same - Dimming range 2~100%, output current accuracy 1% - Standby power input<0.5W, meets the requirements of ErP certification - Excellent pushDIM software processing,good synchronization effect, suppore small gap switch action - Intelligent LED hot-plug protection function - SELV and Class II design, suitable for use inside of the light - Passed CE,ENEC,UKCA,RCM,DALI-2,EL and other certifications - IP20 protection grade, indoor use - Nominal life-time up to 100,000 h - 5-year guarantee Interfaces - DALI-2(DALI-2 DT6) - PUSH(pushDIM) - 1-10V 3in1(1-10V/10V PWM/Rx) Functions - Support central emergency application (dimming normal or fixed output of programming under in DC input - Support self-contained emergency application - Emergency lighting(EL) - Constant light output function(CLO) - Corridor dimming (corridorDIM) - Configure via DALI (PROG) - Protective features (short-circuit, overload,no-load, hot plug-in protection ) Suitableforlights - Suitable for lights with independent drivers such as downlights, spotlights, panel lights, etc - Not suitable for lights with built-in drivers Typicalapplications - LED indoor lighting - LED office lighting - LED architectural lighting - LED commercial lighting info@bokedriver.com tuvsud .com / ps - cert PROG EL corridorDIM CLO www.bokedriver.com REV 1.0 2022-5-13 P1 BOKE Drivers Co.,Ltd. Modelcodingrulesof DLLseries BK - D L L X X X - X X X X z DB Type code(A:Screwless Terminals, B:Wieland quick install connector, C:WAGO quick install connector Function mode(D: DALI-2+pushDIM+1-10V/10V PWM/Rx+EL+CLO+corridorDIM+DALI PROG) Output load voltage range identification code Output current Product series BOKE Functionlist Model Suffix Wired dimming DALI-2 pushDIM 1-10V 3in1 AOC Advanced functions Device Configuration EL CLO corridorDIM DALI interfaces BK-DLL042 DA BK-DLL052 DB DC * The description in this specification is only applicable to the products with the suffix DC and the model are DLL042 and DLL052 . Modellist Model Input voltage Output power Output voltage Output current Dimension Certification BK-DLL042-1050BDA 200-240VAC/DC BK-DLL052-1300BDA 200-240VAC/DC BK-DLL042-1050BDB 200-240VAC/DC BK-DLL052-1300BDB 200-240VAC/DC BK-DLL042-1050BDC 200-240VAC/DC BK-DLL052-1300BDC 200-240VAC/DC 44.1W MAX. 6-42/44/46/49/52/54VDC 54W MAX. 6-40/42/44/46/48/50/54VDC 44.1W MAX. 6-42/44/46/49/52/54VDC 54W MAX. 6-40/42/44/46/48/50/54VDC 44.1W MAX. 6-42/44/46/49/52/54VDC 54W MAX. 6-40/42/44/46/48/50/54VDC 0.3-1.05A 0.55-1.3A 0.3-1.05A 0.55-1.3A 0.3-1.05A 0.55-1.3A L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL L133*W75*H30mm CE,ENEC,UKCA,RCM,DALI-2,EL * The description in this specification is only applicable to the products with the suffix DC and the model are DLL042 and DLL052 . info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P2 BOKE Drivers Co.,Ltd. Technical data Product model Output parameters Regulation method Rated output current range Rated output voltage range Rated output power Output current adjustment Output current ripple LF Output current accuracy BK-DLL042-1050BDB Constant Current 0.3-1.05A 6- 42/44/46/49/52/54VDC 44.1W Max DIP S.W(16 levels) ±2% ±1% Linear regulation ±1% Load regulation No load output voltage ±1% 63VDC Flicker-free(typical) Input parameters Flickering percent(IEEE 1789)=0.138%, Flicker index(IEEE 1789)=0.001, Pst LM = 0.000, SVM = 0.003, (The above parameters are obtained from testing the panel lights) Rated input voltage range Input votage range Input votage shock Input current Input frequency 200-240VAC 200-240VDC 180-264VAC 180-264VDC <380 V AC <0.28A (Rated input voltage input) 0/50/60Hz Input PF/Input DF Input THD Efficiency(typical) PF>0.95 (230V AC & Full load), DF>0.98 (230V AC & Full load) 10% (230V AC & Full load) 88.5% (230V AC & Full load) In-rush current Start/Switchover/Turn off 10.7A peak ,179us duration(50 % Ipeak), see the description below for details <0.7s(AC start),<0.7s(DC start),<0.3s(AC/DC switchover),<0.5s(Turn off ) Switching cycles Power consumption Safety Withstand voltage Mains surge capability Leakage current > 50,000 switching cycles Full load(Pin):49.5W, No load(Pno): N/A, On stand-by(Psb) : <0.5W, Network stand-by(Pnet) : N/A I/P-O/P(LED):3750V AC, I/P-DALI: 1500V AC,O/P-DALI: 1500VAC L-N:2KV(Performance criterion:A) 0.2mA (230V AC & Full load) Isolation resistance Control interface DALI dimming port pushDIM dimming port 1-10V 3in1 dimming port I/P-O/P:100M/500Vdc/25/70% RH Voltage range: 9.5-22.5V, typical 16V, interface current consumption: 1.8mA Voltage range: 180-264V 50/60Hz Voltage range: 0-10V,Maximum output current: 0.3mA Auxiliary power supply Dimming range N/A 2-100% Dimming drive mode AM(amplitude modulation) Emergency support Central emergency system Supported(dimming normal or fixed output of programming under in DC input) Self-contained emergency Supported Environment & Life time Operating temperature Case temperature Operating humidity Storage temp./humidity Ta=-20-45 Tc=85 5-85% RH, not condensed -40-80, 5-85% RH, not condensed IP grade MTBF IP20 500,000H,MIL-HDBK-217F(25) Life-time Vibration resistant Acoustic Noise Environmental protection Nominal life-time up to 100,000 h, see the description below for details 10~500Hz,5G 12min./1cycle,period for 72min. each along X,Y,Z axes <25dB(30cm, Full load) RoHS Certifications and standards Certified Safety EMC CE,ENEC,UKCA,RCM,DALI-2,EL EN61347-1, EN61347-2-13, EN62384 EN55015, EN61000-3-2 , EN61000-3-3, EN61000-4-2,3,4,5,6,8,11, EN61547 DALI-2 IEC 62386-101(DALI-2), IEC 62386-102(DALI-2), IEC 62386-207(DALI-2) EL RF Remarks Compatible IEC 61347-2- 13 Annex J , compatible with EN 60598-2-22 and EN 50172 N/A 1.By default, all parameter are measured at 230VAC input, full load and 25 of ambient temperature. 2.The driver can not be installed inside the light. when the driver is used with the light, the EMC of the whole light needs to be tested. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P3 BOKE Drivers Co.,Ltd. Technical data Product model Output parameters Regulation method Rated output current range Rated output voltage range Rated output power Output current adjustment Output current ripple LF Output current accuracy BK-DLL052-1300BDB Constant Current 0.55-1.3A 6- 40/42/44/46/48/50/54VDC 54W Max DIP S.W(16 levels) ±2% ±1% Linear regulation ±1% Load regulation No load output voltage ±1% 63VDC Flicker-free(typical) Input parameters Flickering percent(IEEE 1789)=0.173%, Flicker index(IEEE 1789)=0.000, Pst LM = 0.000, SVM = 0.004, (The above parameters are obtained from testing the panel lights) Rated input voltage range Input votage range Input votage shock Input current Input frequency 200-240VAC 200-240VDC 180-264VAC 180-264VDC <380 V AC <0.32A (Rated input voltage input) 0/50/60Hz Input PF/Input DF Input THD Efficiency(typical) PF>0.95 (230V AC & Full load), DF>0.98 (230V AC & Full load) 10% (230V AC & Full load) 88.5% (230V AC & Full load) In-rush current Start/Switchover/Turn off 11.4A peak ,190us duration(50 % Ipeak), see the description below for details <0.7s(AC start),<0.7s(DC start),<0.3s(AC/DC switchover),<0.5s(Turn off ) Switching cycles Power consumption Safety Withstand voltage Mains surge capability Leakage current > 50,000 switching cycles Full load(Pin):60W, No load(Pno): N/A, On stand-by(Psb) : <0.5W, Network stand-by(Pnet) : N/A I/P-O/P(LED):3750V AC, I/P-DALI: 1500V AC,O/P-DALI: 1500VAC L-N:2KV(Performance criterion:A) 0.26mA (230V AC & Full load) Isolation resistance Control interface DALI dimming port pushDIM dimming port 1-10V 3in1 dimming port I/P-O/P:100M/500Vdc/25/70% RH Voltage range: 9.5-22.5V, typical 16V, interface current consumption: 1.8mA Voltage range: 180-264V 50/60Hz Voltage range: 0-10V,Maximum output current: 0.3mA Auxiliary power supply Dimming range N/A 2-100% Dimming drive mode AM(amplitude modulation) Emergency support Central emergency system Supported(dimming normal or fixed output of programming under in DC input) Self-contained emergency Supported Environment & Life time Operating temperature Case temperature Operating humidity Storage temp./humidity Ta=-20-45 Tc=85 5-85% RH, not condensed -40-80, 5-85% RH, not condensed IP grade MTBF IP20 500,000H,MIL-HDBK-217F(25) Life-time Vibration resistant Acoustic Noise Environmental protection Nominal life-time up to 100,000 h, see the description below for details 10~500Hz,5G 12min./1cycle,period for 72min. each along X,Y,Z axes <25dB(30cm, Full load) RoHS Certifications and standards Certified Safety EMC CE,ENEC,UKCA,RCM,DALI-2,EL EN61347-1, EN61347-2-13, EN62384 EN55015, EN61000-3-2 , EN61000-3-3, EN61000-4-2,3,4,5,6,8,11, EN61547 DALI-2 IEC 62386-101(DALI-2), IEC 62386-102(DALI-2), IEC 62386-207(DALI-2) EL RF Remarks Compatible IEC 61347-2- 13 Annex J , compatible with EN 60598-2-22 and EN 50172 N/A 1.By default, all parameter are measured at 230VAC input, full load and 25 of ambient temperature. 2.The driver can not be installed inside the light. when the driver is used with the light, the EMC of the whole light needs to be tested. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P4 BOKE Drivers Co.,Ltd. Electricalvalues BK-DLL042-1050BDB Efficiency vs load Eficiency (%) 91.00 89.00 87.00 85.00 83.00 81.00 79.00 77.00 75.00 73.00 71.00 69.00 67.00 65.00 63.00 61.00 59.00 57.00 55.00 10% 1.05A 0.65A 20% 30% 40% 50% 1A 0.6A 0.95A 0.55A 0.9A 0.5A 60% 70% 80% 90% 0.85A 0.8A 0.45A 0.4A 0.75A 0.35A 100% 0.7A 0.3A Load(%) Power factor vs. Load 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 0.400 10% 20% 1.05A 0.65A 1A 0.6A 30% 40% 50% 60% 0.95A 0.55A 0.9A 0.5A 0.85A 0.45A 70% 0.8A 0.4A 80% 90% 100% 0.75A 0.35A 0.7A 0.3A Load(%) PF Expectedlife-time Life-time vs. case temperature Life-time(H) 110,000 100,000 90,000 80,000 70,000 60,000 50,000 40,000 30,000 20,000 50 55 60 65 70 75 80 85 90 Case temperature(Tc) THD DF THD vs. Load 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 10% 1.05A 0.65A 20% 1A 0.6A 30% 40% 50% 0.95A 0.9A 0.55A 0.5A 60% 0.85A 0.45A 70% 80% 90% 100% 0.8A 0.75A 0.7A 0.4A 0.35A 0.3A Load(%) Displacement factor vs. Load 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 10% 20% 1.05A 1A 0.65A 0.6A 30% 40% 50% 60% 0.95A 0.55A 0.9A 0.5A 0.85A 0.45A 70% 80% 90% 100% 0.8A 0.4A 0.75A 0.7A 0.35A 0.3A Load(%) -The life-time of the LED driver is shown in the figure above (calculated based on the 90% survival rate). - The relation of tc to ta temperature depends also on the luminaire design. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P5 BOKE Drivers Co.,Ltd. Electricalvalues Eficiency (%) BK-DLL052-1300BDB Efficiency vs load 92.00 90.00 88.00 86.00 84.00 82.00 80.00 78.00 76.00 74.00 72.00 70.00 68.00 10% 20% 30% 1.3A 0.9A 1.25A 0.85A 40% 1.2A 0.8A 50% 1.15A 0.75A 60% 70% 80% 1.1A 1.05A 0.7A 0.65A 90% 1.0A 0.6A 100% 0.95A 0.55A Load(%) Power factor vs. Load 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 10% 20% 30% 40% 50% 1.3A 0.9A 1.25A 0.85A 1.2A 0.8A 1.15A 0.75A 60% 70% 80% 90% 100% 1.1A 0.7A 1.05A 0.65A 1.0A 0.6A 0.95A 0.55A Load(%) PF Expectedlife-time Life-time vs. case temperature Life-time(H) 110,000 100,000 90,000 80,000 70,000 60,000 50,000 40,000 30,000 20,000 50 55 60 65 70 75 80 85 90 Case temperature(Tc) THD DF THD vs. Load 55 50 45 40 35 30 25 20 15 10 5 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 1.3A 1.25A 0.9A 0.85A 1.2A 0.8A 1.15A 0.75A 1.1A 0.7A 1.05A 0.65A 1.0A 0.6A 0.95A 0.55A Load(%) Displacement factor vs. Load 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 10% 1.3A 0.9A 20% 30% 40% 50% 1.25A 0.85A 1.2A 0.8A 1.15A 0.75A 60% 70% 80% 90% 100% 1.1A 0.7A 1.05A 0.65A 1.0A 0.6A 0.95A 0.55A Load(%) -The life-time of the LED driver is shown in the figure above (calculated based on the 90% survival rate). - The relation of tc to ta temperature depends also on the luminaire design. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P6 BOKE Drivers Co.,Ltd. Surge Model Ipeak Twidth Condition Relative number of MCB/pcs B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25 BK-DLL042-1050BDB 10.7A 179us AC 230V,Full load, Cold start,Ta30, 32 41 50 63 79 32 41 50 63 79 32 41 50 63 79 MCB is not installed BK-DLL052-1300BDB 11.4A 190us side by side 26 33 41 51 64 26 33 41 51 64 26 33 41 51 64 Ipeak Twidth 50% Ipeak Remarks - The number of drives mounted under different MCBs in the table is the maximum value. Please do not exceed this number during installation. - Calculation uses typical values from ABB series S200 as a reference. - Different brands and models of miniature circuit breakers, the number of drives mounted will be slightly different. - If the ambient temperature of the MCB installation exceeds 30°C or multiple MCBs are installed side by side, the number of drives mounted will be reduced and the calculation needs to be recalculated. - Electrician's usually consider Type B for household lighting and Type C for commercial lighting application. Functions Output short-circuit behaviour - In case of a short-circuit at the LED output ,the LED output is switched off. - After restart of the LED driver ,the output will be activated again. Output no-load operation - The LED driver will not be damaged in no-load operation. - The output will be deactivated and is therefore free of voltage. - If a LED load is connected , the device has to be restarted before the output will be activated again. Output overload protection - If the output voltage range is exceeded the LED driver turns off the LED output. - After restart of the LED driver the output will be activated again. Output hot plug-in In the following two cases,the LED driver will automatically turn off the output to protect the LED - When the driver is powered on first and the LED is connected later. - When the driver is powered on,disconnected and connecred again. - After restart of the LED driver the output will be activated again. Driver restart method There are two ways to restart the device: - Through the AC input portr:disconnect the AC of the driver and power it again. - Through dimming interface. DALI:send"OFF"command first,then send "MAX"command. pushDIM:short press PUSH switch two times,then long press PUSH switch. 1-10V:first adjust the output voltage of the dimmer to 0.9v or below, then adjust it to 1V or above. Insulationbetweencircuits Adjustable output current (AOC) - The output current of the driver can be adjusted within a certain range, and 2 options can be selected through the device configuration software. Setting 1 (default): DIP-switch The output current is determined by the selection of the DIP-switch. Setting 2: Programming The output current is determined by the programming setting. Corridor dimming (corridorDIM) - Please see the "corridorDIM dimming" section. Constant light output (CLO) - The luminous flux of a LED decreases constantly over the life-time. - The CLO function ensures that the emitted luminous flux remains stable.For that purpose the LED current will increase continuously over the LED life-time. - In device configuration it is possible to select a start value(in percent) and an expected life-time.The LED Driver adjusts the current afterwards automatically. Emergency lighting(EL) - The driver works normally under DC input. - When the driver is applied in DC input, the positive pole of the DC cable should be connected to the ACL/DC+ terminal, and the negative pole of the DC cable should be connected to the ACN/DC- terminal. If the connection is reversed, the driver will not be damaged, but it will affect the EL function normal work. - The output response action after DC input can be set through device configuration software. Setting (default): When DC input, the output of the driver remains unchanged, and the dimming function responds normally. Setting : When DC input, the output of the driver jumps to the set brightness, and the dimming function is invalid. Programming(PROG) -Connect the "DALI Programmer" programmer to the DALI port of the driver and use the"device configuration" software to configure the functions of the driver. Device configuration(EasySet) - Please see the"Device configuration" section. - For further information see device configuration instruction manual. Isolation Input Output Case Input - Double Double Output Double Basic Case Double Basic - DALI Basic Double Double PUSH - Double Double DIM Double Basic PWM Double Basic info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P7 Label BOKE Drivers Co.,Ltd. DIP-switch&outputcurrent Pin(w) Output typ. Prated(w) Irated(mA) Voltage(Vdc) 1 2 3 4 19.5 16.2 300 6-54 ON ON ON ON 21.5 18.9 350 24.5 21.6 400 27.5 24.3 450 30.5 27.0 500 6-54 -- ON ON ON 6-54 ON -- ON ON 6-54 -- -- ON ON 6-54 ON ON -- ON 33.5 29.7 550 6-54 -- ON -- ON 36.5 32.4 600 39.5 35.1 650 6-54 ON -- -- ON 6-54 - - - - -- ON 42.5 37.8 700 45.5 40.5 750 . 41.6 6-54 ON ON ON -- 6-54 -- ON ON -- - ON -- ON -- . 41.6 - -- -- ON -- . 41.4 . 41.8 - ON ON -- - - - -- ON -- - - . 42.0 . 44.1 - ON -- - - - - - - - - - - - - - Pin(w) Output typ. Prated(w) Irated(mA) Voltage(Vdc) 1 2 3 4 33.5 29.7 550 6-54 ON ON ON ON 36.5 32.4 600 6-54 -- ON ON ON 39.0 35.1 650 42.5 37.8 700 45.0 40.5 750 6-54 ON -- ON ON 6-54 -- -- ON ON 6-54 ON ON -- ON 48.5 43.2 800 6-54 -- ON -- ON 51.5 45.9 850 54.5 48.6 900 6-54 ON -- -- ON 6-54 - - - - -- ON 58.0 51.3 950 60.0 54.0 1000 59.0 52.5 1050 6-54 6-54 6-50 ON ON ON --- ON ON -ON -- ON -- 59.5 52.8 1100 6-48 -- -- ON -- 60.0 52.9 1150 59.5 52.8 1200 6-46 ON ON -- - - 6-44 -- ON -- - - 59.5 52.5 1250 59.0 52.0 1300 6-42 ON -- - - - - 6-40 - - - - - - - - Remarks: 1. It means that this item is the factory default current. -- 2. It means that this channel is OFF. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P8 BOKE Drivers Co.,Ltd. DALIdimmingapplication Wiring diagram FG N L DA DA Optioal DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- Max. x64 ActivatingDALIdimmingmode Please refer to the table below - After installation according to the wiring diagram of DALI dimming application, the driver will automatically switch to the DALI control mode after receiving any DALI command. Remarks: - Standard DALI control line voltage range:9.5V to 22.5V ,type 16V. - The two DALI control lines polarity-reversible. - Max. 64 DALI drivers per DALI control line. - The maximum distance length of the DALI control line is 300m at 2×1.5mm2. - DALI bus can be wired together with any mains voltage cables, but separate wiring is recommended. - The configuration parameters of the driver can be set through the DALI configuration tool or DALI application controller during installation, such as setting device address, group address, power-on level, bus-failure level, scene level, fade time, dimming curve, etc. Power-onlevel: When the driver is in DALI- dimming mode, the factory default level after each power-on is the brightest. The power-on level can be set through the DALI configuration tool or DALI application controller during installation, and can be set to memory or fixed any brightness (such as off, darkest, %, etc.). Note: The recommended setting for the default factory power-on level of the DALI- driver is the brightest in the DALI- standard. Output current(%) Cable size 2×0.50mm2 2×0.75mm2 2×1.00mm2 2×1.50mm2 Distance max.100m max.150m max.200m max.300m 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 0 Logarithmic dimmer curve 50 100 150 200 254 dimming level Remarks: The dimming curve can be selected by DALI configuration. The default is logarithmic dimming curve. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P9 BOKE Drivers Co.,Ltd. pushDIMdimmingapplication Wiring diagram L N FG Optioal pushbuttom DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- Max. x50 ActivatingpushDIMdimmingmode - After installation according to the wiring diagram of pushDIM dimming application, short press the pushbuttom 5 times within 3 seconds, the driver will automatically switch to pushDIM dimming mode. - After activating pushDIM control mode, CorridorDIM mode will be automatically closed. Remarks: Max. 50 drivers per pushDIM control line. Turn on or turn off:short press pushbuttom for 0.2-1s. Dimming: long press push buttom for 1-5s. Power on status: after power on,the light state will be the same as the lighting on state. If the light is on before power on,the light will be on after power on again,brightness will be the same as the last lighting on brightness. If the light is off before power off,the light will be off after power on again,short press the pushbuttom,then the light will be on,the brightness will be the same as the last brightness. A%(Last) before power off Power off then power on A%(Last) After power on A%(Last) before power off Dim 0%(OFF) before power off Power off then power on 0%(OFF) after power on Short press pushbuttom A%(Last) after press buttom Multiplelightssynchronizecontroloperation method 1 Step 1:long press the pushbuttom,confirm each light is on. Step 2:short press the pushbuttom,confirm each light is off. Step 3:long press the pushbuttom,confirm each light is from darkest to brightest and all the lights are synchronous. method 2 - Long press the pushbuttom 15s,all lights output to the brightest state. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P10 BOKE Drivers Co.,Ltd. corridorDIMdimming Wiring diagram Optioal FG N L Lout sensor DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- ActivatingthecorridorDIMdimmingmode - Method 1: Activating by sensor. After installation according to the wiring diagram of corridorDIM dimming application, you can use the following two methods to activate. Method 1: Keep the movement in the effective sensing area for 5 minutes, the corridorDIM dimming function of the drive will be activated and light up 100% (under the default setting). Method 2: Activate by Hold-time Set the hold-time of the sensor to more than 5 minutes. When the motion sensor detects a person and turns on the output for 5 minutes, the corridorDIM dimming function will be activated and the light will be on 100% (Default), finally restore the hold-time that the sensor actually needs. -Method 2: Activate by normal switch After installation according to the wiring diagram of the corridorDIM dimming application, first replace the sensor with a normal switch, and then turn on the normal switch for 5 minutes, and the driver will automatically switch to corridorDIM dimming mode, then remove the normal switch and replace it with the sensor. - After activating the corridorDIM dimming mode, the pushDIM dimming mode will be automatically deactivate . Remarks - During normal working,It is recommended to set the hold-time of the motion sensor to the minimum. - Need to use a motion sensor with AC switch. corridorDIMworkingprocess Brightness level PL AL I II F1 T1 III IV T F V Time T F3 - The parameters of corridorDIM can be set through the configuration tool. - corridorDIM is not activated by default. Name Fade-in time Presence level Hold-on time Run-on time Fade-out time Absence level Stand-by Time Fade-off time Symbol Factory setting Settable range F1 1s 0-100s PL 100% 0-100% T1 By sensor setting T2 180s F2 5s 0-60000s 0-100s AL 10% 0-100% T3 unlimited 0-59999s,60000s(unlimited) F3 0s 0-100s info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P11 BOKE Drivers Co.,Ltd. 1-10V/10VPWMdimmingapplication Wiring diagram L DA Optioal FG DA LED+ DLL driver LED- DIM+ N ACN/DC- DIM- ACL/DC+ FG N DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- Lout DIM+ DIMActivating1-10V/10VPWMdimmingmode x30 -Method 1: After installation according to the wiring diagram of the 1-10V / 10V PWM dimming application, adjust the dimmer to the minimum and then to the maximum, the driver will automatically activate the 1-10V control mode. -Method 2: Short-circuit the DIM+ and DIM- ports for 2s, the driver will automatically activate the 1-10V control mode. Remarks: - Dimming interface characteristics: 0.9V and below are closed, 1V is the darkest, 10V is the brightest,1-10V is the dimming range. - The dimming interface distinguishes between positive and negative, DIM is positive, GND is negative, please do not reverse. - Dimming interface does not support voltage access higher than 20V, otherwise it will cause damage to the internal components. - When the dimming interface is open, the driver outputs the maximum current. When the interface is short-circuited, the current output is closed. - When multiple synchronous dimming is required, the positive poles of the dimming interface of each driver are connected together, and the negative poles are connected together. - Support passive dimmer or isolated active dimmer dimming, does not support non-isolated active dimmer dimming. - In general, it is recommended that the number of mounted drives does not exceed 30pcs, and the wiring length does not exceed 100m. - It is recommended that the dimming wires should not be lower than the 22AWG wire. - Do not put the dimming wires with high voltage or interference sources. If it is unavoidable, please use the shielded wires. - It is recommended to conduct sample test first and confirm the dimming effect before bulk purchase. - If you need a drive with 0-10V dimming characteristics, please contact BOKE. Dimmingcurve Output current Output current Output current vs.Dimming Voltage(Typical) 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 1% 0 0.9 1 2 3 4 5 6 78 9 9.7 10 Dimming Voltage(Vdc) Output current 10V PWM Duty Cycle(Typical) 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 1% 0 9% 10% 20% 30% 40% 50% 60% 70% 80% 90% 97%100% 10V PWM Duty Cycle *Frequency range:100Hz-3KHz info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P12 BOKE Drivers Co.,Ltd. 100Kpotentiometerdimmingapplication Wiring diagram FG N L Optioal DA DA ACN/DCACL/DC+ DLL driver LED+ LEDDIM+ DIM- DIM+ DIM- 100K Potentiometer - Only one driver can be mounted in the potentiometer dimming mode. - Dimming interface does not support voltage access higher than 20V, otherwise it will cause damage to the internal components. - When the dimming interface is open, the driver outputs the maximum current. When the interface is short-circuited, the currentoutput is closed. - It is recommended that the dimming wires should not be lower than the 22AWG wire. - Do not put the dimming wires with high voltage or interference sources. If it is unavoidable, please use the shielded wires. - It is recommended to conduct sample test first and confirm the dimming effect before bulk purchase. - If you need a drive with 0-10V dimming characteristics, please contact BOKE. Dimmingcurve Output current(%) Compatible with 100K potentiometer 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 0K 5K 10K 20K 30K 40K 50K 60K 70K 80K 90K 100K Adjustable resistance info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P13 BOKE Drivers Co.,Ltd. Device configuration USB EasySet USB 12 3 Switch USB DALI OK NG DALI Programmer ERR DA1 DA2 DA1 DA2 DALI Programmer DA DA Optioal FG ACN ACN/DC- ACL ACL/DC+ DLL driver LED+ LEDDIM+ DIM- Need to be powered Configure tools and software Name DALI Configurator PC Software Parameters configure Configuration items Product information Adjustable output current(AOC) PUSH dimming function(pushDIM) 1-10V dimming (1-10V) Corridor dimming (corridorDIM) Emergency lighting(EL) Constant light output function(CLO) Hot plug-in protection(HPP) Run time Other parameters Brand BOKE BOKE Name DALI Programmer EasySet Minimum version V1.0.0 V1.0.0 Factory settings - Activated Activated Activated Activated Activated(setting 1) Deactivated Activated Parameter configuration NO YES YES YES YES YES YES YES NO YES Read/Wirte Read Only Read/Wirte Read/Wirte Read/Wirte Read/Wirte Read/Wirte Read/Wirte Read/Wirte Read Only info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P14 BOKE Drivers Co.,Ltd. Optionalaccessories Pluggable strain relief, 5Pole (Wieland) Model: BK-BAS005B2(Optional accessories) Pluggable connector Wieland(92.953.5453.0) Applicationdiagram Model: BK-BAS005B1(Factory default) Pluggable connector Wieland(92.052.8658.0) info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P15 BOKE Drivers Co.,Ltd. Installation Mechanicaldimensions Unit:mm BK-DLL042-1050BDB/BK-DLL052-1300BDB . 4.2 135.5 . . 64.0 . INPUT Numbering 1 2 3 4 5 function DA DA FG ACN/DCACL/DC+ OUTPUT Numbering 1 2 3 4 function LED+ LEDDIM+ DIM- colour red black green black Output wire 0.75-1.5mm2 8-9mm Installationnote Hotplug-in - Hot plug-in is not supported due to residual output voltage of > 0 V. - If a LED load is connected the device has to be restarted. - Restart can be achieved by re-powering the driver or executing a on/off command (action) through the control interface (DALI, pushDIM,1-10V) Wiringguidelines - All connections must be kept as short as possible to ensure good EMI behaviour. - Mains leads should be kept apart from LED Driver and other leads (ideally 5 10 cm distance) - Max. lenght of output wires is 2 m. - Incorrect wiring can damage LED modules. Mountingscrewspecificationsandtorque - Max. torque at the clamping screw: 0.5 Nm / M4 ReplaceLEDmodule 1. Mains off 2. Remove LED module 3. Wait for 5 seconds 4. Connect LED module again Installation requirements -Thedrivershouldbeinstalledinadry,acid-free,oil-free,fat-freeenvironment. - The installation ambient temperature of the drive shall not exceed the value of Ta at any time. - The temperature of the mounting surface of the driver should be lower than -Thedrivershouldkeepacertaindistancefromtheheatingstuff(suchastheluminaireradiator). - If the driver is used externally (it needs to be used with the accessories), the installation of the driver should also meet the following conditions: 1.The driver should be a certain distance between the drivers, as shown in Figure 1. 2.The driver keeps a certain distance from surrounding objects, as shown in Figure 2. 15cm 10mm 15cm 15cm 15cm 70mm 20mm Figure 1 Figure 2 info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P16 Packaging BOKE Drivers Co.,Ltd. Product Packaging 16pcs×2layer=32pcs/CIN Model BK-DLL - BDB BK-DLL052-1300BDB Product size L *W *H mm Weight g Packaging size L *W *H mm L Carton size Qty/carton *W *H mm pcs N.W . kg L198*W75*H30mm 287g L225*W38*H82mm L465*W325*H185mm 32pcs 9.18kg G.W . kg 10.3kg Additional information 1. The life and MTBF of the product are for reference only, and do not represent a warranty statement. 2. For more information, please send an email to info@bokedriver.com. info@bokedriver.com www.bokedriver.com REV 1.0 2022-5-13 P17Corel PDF Engine Version 22.0.0.412