Keurig K10 MINI Plus Brewer Owner's Manual

Important Safeguards

When using electrical appliances, basic safety precautions should be followed, including:

• Read all instructions before using.
• Do not touch hot surfaces. Use handles and knobs.
• Ensure the appliance is properly installed and located.
• Do not use accessory attachments not recommended by the manufacturer.
• Do not place on or near hot gas or electric burners, or in a heated oven.
• Do not use outdoors.
• Do not immerse cords, plugs, or the appliance in water or other liquids.
• Do not overfill the Cold Water Reservoir.
• Use only water in this appliance.
• Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before handling parts.
• Plug the appliance into its own electrical outlet to prevent issues with other appliances.
• Do not operate with a damaged cord or plug, or after malfunction.
• Do not let the cord hang over edges or touch hot surfaces.
• To disconnect, turn the Power Button to "OFF" and remove the plug.
• Close supervision is necessary when used by or near children.
• Do not lift the brewer handle while brewing is in progress.
• Always keep the Cold Water Reservoir Lid closed unless refilling.
• The appliance is equipped with a grounding wire and plug. Use a properly grounded 3-hole outlet.
• Replace standard 2-prong outlets with a properly grounded 3-prong outlet.
• Do not cut or remove the third (ground) prong.
• Consult a qualified electrician if grounding instructions are unclear.
• Do not use the appliance for other than its intended use.

CAUTION: There are two sharp needles that puncture the K-Cup® pack. Avoid risk of injury by not putting fingers in the K-Cup® Pack Assembly Housing.

CAUTION: Extremely hot water is present during the brew process. Avoid risk of injury by not lifting the Handle or opening the K-Cup® Pack Assembly Housing during brewing.

CAUTION: Always keep the brewer in its upright position.

Short Cord Instructions: A short power supply cord is provided. If an extension cord is used, ensure its electrical rating is at least as great as the appliance's, it is arranged to prevent tripping, and it includes a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

WARNING: KEEP ALL PLASTIC BAGS AWAY FROM CHILDREN.

WARNING: THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING TO USERS AND PARENTS:

• Do not permit children to use the brewer without adult supervision.
• Special Notice for Hot Cocoa Users: Immediately after using a Hot Cocoa K-Cup® pack, run a Hot Water Brew Cycle without a K-Cup® pack to avoid clogging the exit needle.

WARNING: RISK OF FIRE OR ELECTRIC SHOCK. DO NOT OPEN.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

Section 1: Brewer Overview

The Keurig K10 MINI Plus Brewer consists of the following parts:

• A: Water Level Guide
• B: Handle
• C: K-Cup® Pack Holder Assembly
• D: K-Cup® Pack Holder
• E: Funnel
• F: K-Cup® Pack Assembly Housing
• G: Drip Tray Overfill Indicator
• H: Drip Tray Plate
• I: Drip Tray
• J: Cold Water Reservoir Lid
• K: Cold Water Reservoir
• L: BREW Button
• M: LED Indicator
• N: Power Button
• O: Power Cord
• P: Drip Tray Base

Diagram showing the Keurig K10 MINI Plus Brewer with labeled parts.

Section 2: Helpful Hints

• Plug Power Cord into an Independent, Grounded Outlet: Avoid overloading circuits.
• Initial Cleansing Brew: Perform a cleansing brew without a K-Cup® pack before first use.
• One Cup at a Time: The brewer makes one beverage at a time and requires fresh water for each brew.
• Water Quality: Keurig recommends bottled or filtered water for best taste. Avoid distilled or reverse osmosis water.
• Customize Your Brew: Use K-Cup® pack varieties and fill levels to customize size, flavor, and strength. Select Extra Bold K-Cup® packs for a more intense flavor. Use the Water Level Guide for brew size.
• Brewing Iced Beverages: Brew hot over ice. Place a tall cup filled with ice on the Drip Tray. Use K-Cup® packs with the "Brew Over Ice" icon. Do not brew into glass cups.
• Remove K-Cup® Pack After Use: See page 8 for brewing instructions.
• Brewing into a Tall Mug: Remove the Drip Tray Assembly and place the tall mug on the Drip Tray Base.
• The Drip Tray: Catches liquid overflow. Empty when the red Drip Tray Overflow Indicator appears.
• Automatic Shut-Off: The brewer shuts off after 90 seconds of inactivity. Press the Power Button to restart.
• Clean Your Brewer Regularly: Clean external and internal components as recommended.
• De-Scaling: Perform de-scaling every 3-6 months or when white deposits appear to maintain performance.
• Storage: Empty the Drip Tray and Internal Hot Water Tank. Store upright in a safe, dry, frost-free environment.

Section 3: Buttons & Indicators

Power Button: Press to turn the brewer on and off. Does not illuminate.

Add Water Indicator: Flashing Blue - Fill the Cold Water Reservoir to the desired level (6, 8, or 10 oz.).

Handle Indicator: Flashing Blue - Indicates minimum water (6 oz.) has been poured. Light continues flashing until the Handle is lifted.

Brew Button:

• Flashing Blue: Ready to brew. Press to begin.
• Flashing Red: Water is heating (approx. 2 minutes).
• Solid Red: Brewing and dispensing has begun.

Your Next Brew: After brewing, the Add Water Indicator light appears. You can start the next beverage or power off.

Automatic Shut-Off: The brewer automatically shuts off after 90 seconds of idle time. Press the Power Button to restart.

Drip Tray Overfill Indicator: A red float indicates the Drip Tray is nearly full. Slide out and empty the Drip Tray.

Section 4: Set-Up & Operation

Initial Cleansing & First Brew

CAUTION: Avoid injury from sharp needles in the K-Cup® Pack Assembly Housing.

CAUTION: Avoid injury from extremely hot water during brewing. Do not lift the Handle or open the K-Cup® Pack Assembly Housing until brewing is complete.

1. Remove all tape and cardboard.
2. Plug the Power Cord into an independent, grounded outlet.
3. Press the Power Button. The Add Water Indicator will flash blue.
4. Lift the Cold Water Reservoir Lid.
5. Pour water into the Cold Water Reservoir up to the rim of your desired fill level (minimum 6 oz., maximum 10 oz.). Lower the lid.
6. Lift the Handle. Water begins to drain into the brewer.
7. Place a mug on the Drip Tray.
8. Insert the K-Cup® pack into the K-Cup® Pack Holder.
9. Wait until all water has drained (approx. 5 seconds) before lowering the Handle completely.
10. The BREW Button will flash blue. Press the BREW Button.
11. The BREW Button will flash red (heating, approx. 2 minutes), then turn solid red when dispensing begins.
12. Remove the used K-Cup® pack after brewing. The K-Cup® pack will be hot.
13. Enjoy your beverage! The brewer is ready for use or can be powered off. It will automatically shut off after 90 seconds.
14. If performing the initial cleansing brew, discard hot water into the sink.

Section 5: Cleaning & Maintenance

Cleaning External Parts

IMPORTANT: Ensure the brewer is unplugged before cleaning.

Regular cleaning of external components is recommended:

• Brewer external housing
• Drip Tray
• Drip Tray Plate

Never immerse the brewer in water or other liquids.

Clean external parts with a damp, non-abrasive, lint-free cloth.

Drip Tray and Drip Tray Plate:

• Empty the Drip Tray when the red Drip Tray Overfill Indicator appears.
• Clean the Drip Tray with a damp, non-abrasive, lint-free cloth.
• Do not put the Drip Tray or Drip Tray Plate in the dishwasher.

Cleaning the K-Cup® Pack Holder Assembly

IMPORTANT: Ensure the brewer is unplugged before cleaning.

Parts include: Funnel, K-Cup® Pack Holder with Exit Needle.

These parts can be placed on the top shelf of the dishwasher using a low temperature cycle.

1. Lift the Handle to open. Grasp the K-Cup® Pack Holder and push up from the bottom to release it.
2. Separate the Funnel from the K-Cup® Pack Holder by pulling until it snaps free.
3. Clean the Exit Needle on the bottom of the K-Cup® Pack Holder. If clogged, insert a paper clip from below. Avoid touching the needles.
4. Snap the Funnel back into the K-Cup® Pack Holder.
5. Align the K-Cup® Pack Holder Assembly with the opening using the front ribs as a guide and snap into place from the top.

Cleaning the Cold Water Reservoir

Discoloration or spotting in the reservoir is normal and does not affect operation. Clean regularly to minimize build-up.

1. Lift the lid.
2. Remove the Water Level Guide (not dishwasher safe).
3. Clean inside the reservoir with a damp, lint-free cloth.
4. Replace the Water Level Guide and lower the lid.

Emptying the Internal Hot Water Tank

Brewer must be powered off but plugged in.

1. Lower the Cold Water Reservoir Lid.
2. Place a mug on the Drip Tray.
3. Press and hold the BREW Button until all water is dispensed into the mug.
4. There will be a 3-5 second delay before water dispenses.

De-Scaling Your Brewer

Calcium deposits can hinder brewer performance. De-scaling helps maintain the heating element and internal parts.

De-scale every 3-6 months or when white deposits appear.

You will need: 20 oz. undiluted white vinegar, 12 oz. ceramic mug, access to a sink.

Step 1: First Vinegar Rinse

1. Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.
2. Place the ceramic mug on the Drip Tray.
3. Lift the Handle (do not add K-Cup® pack).
4. After 5 seconds, lower the Handle.
5. Press the BREW Button. It will flash red, then turn solid red.
6. Once dispensed, discard hot contents into the sink.

Step 2: Second Vinegar Rinse

1. Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.
2. Place the ceramic mug on the Drip Tray.
3. Lift the Handle (do not add K-Cup® pack).
4. After 5 seconds, lower the Handle.
5. Press the BREW Button. It will flash red.
6. When it turns solid red, power off as it starts to dispense.
7. Allow the brewer to sit for 30 minutes.
8. Power on, lift and lower the Handle, then press the BREW Button.
9. Once dispensed, discard hot contents into the sink.

Step 3: Fresh Water Rinse

1. Fill the Cold Water Reservoir with 10 oz. of fresh water.
2. Place the ceramic mug on the Drip Tray.
3. Lift the Handle (do not add K-Cup® pack).
4. Lower the Handle and continue brewing until hot water is dispensed. Discard hot contents.
5. Repeat this cleansing brew process three more times to remove any residual vinegar taste.

The brewer is now ready for normal use.

Storage

Empty the Internal Hot Water Tank and Cold Water Reservoir before storing. Store upright in a safe, frost-free environment.

Storing in cold temperatures may cause damage. Before use after storage, wipe the reservoir with a damp cloth and run three cleansing brews (without K-Cup® packs).

Allow the brewer to rest at room temperature for at least 2 hours before powering on.

Storing the Power Cord

A compartment behind the brewer is available to hold the Power Cord during transport or storage.

Service

This brewer is not user-serviceable beyond recommended cleaning and maintenance. Refer to the Warranty section for service information.

Section 6: Troubleshooting

Should other issues arise, please call Keurig Customer Service at 1.866.901.BREW (2739).

Section 7: Warranty

Limited One Year Warranty

Keurig, Incorporated warrants the brewer against defects in materials or workmanship under normal home use for one year from the date of purchase. Proof of purchase is required for warranty service. Keurig will, at its option, repair or replace a defective brewer with new or reconditioned parts.

This warranty applies to brewers operated in the United States and Canada and provides specific legal rights that may vary by state or province.

Only Keurig Brewed® K-Cup® brand packs and accessories guarantee proper function and lifetime. Damage or malfunction from non-Keurig products may void the warranty or incur a service fee.

What is not covered by the limited warranty?

This warranty does not cover consequential or incidental damages such as property damage. Some states/provinces may not allow limitations on incidental or consequential damages.

This warranty also does not cover damages caused by:

• Non Keurig Brewed® K-Cup® brand packs or accessories
• Services performed by anyone other than Keurig or authorized service providers
• Use of non-genuine Keurig® parts
• External causes such as abuse, misuse, inappropriate power supply, or acts of God

Other limitations

This warranty is exclusive and in lieu of any other express warranty. Keurig specifically disclaims all other warranties, including implied warranties of merchantability or fitness for any particular purpose. Some states/provinces may not allow disclaimers of implied warranties.

How do you obtain warranty service?

Call Keurig Customer Service at 1.866.901.BREW (2739). Do not return the brewer for servicing without first obtaining an Authorization to Return (ATR) number from Keurig Customer Service.

Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)

Scan. Click. Call!

Scan for videos about caring for your brewer! Scan the QR code or visit bit.ly/NjTZ8W for step-by-step videos.

Have questions? We're here to help!

Call Keurig at 1.866.901.BREW (2739) for quick answers.