Instruction Manual

Important Information

Please read this Instruction Manual before installing or using your product.

Please keep this Instruction Manual properly in a safe place for future reference.

Safety Precautions

To prevent damage to the unit and possible injury to users, please follow the safety warnings. Please be sure to carefully read through the user's manual before installation. Keep the user's manual after installation to refer to for troubleshooting advice.

Symbols And Meanings

⚠️ WARNING: Could result in serious injury or death.

The following symbols are used to indicate important safety precautions when using the product.

• ? Prohibited: [Prohibited symbol]
• ⓘ Caution: Pay close attention; caution.

General Warnings

⚠️ WARNING: It is not allowed to continue using if the product has some breakdown:

• Product heat abnormally;
• Product is smoking;
• Product has abnormal sound and smell;
• Product is leaking, broken or damaged;
• Toilet pan is blocked, etc.

When a breakdown occurs, if not handled in time and continued use, it might trigger problems like electric shock, injury, fire, or water penetration inside the room, etc.

Cleaning Restrictions: Banana oil, gasoline, putty-powder, nylon brush, or other (non-neutral) detergent is not allowed to clean the plastic parts like the toilet seat cover, otherwise it might trigger chemical reactions or leakage, damage the product, and cause people injury.

Electrical Safety:

• Loosened electric outlets are not allowed as they might trigger electric shock or fire.
• It is not allowed to pull out and plug in the electric plug with wet hands as it might trigger electric shock or fire.
• It is not allowed to touch the electric plug when it is thundering and lighting as it might trigger electric shock.
• It is not allowed to use other electric resources; the load of using electric outlets should not be too big, as it might trigger fire due to over-heating.
• Detergent, water, wash detergent, or urine is not allowed to spill into the body and electric outlet, as it might trigger electric shock or fire.

Usage Restrictions:

• It is not allowed for children to stand or place heavy goods on the seat and cover, toilet pan, or seat body. Heavy hitting or knocking is not allowed.
• It is not allowed to disassemble or repair this product. If repair is necessary, it must be done by a professional repair person, otherwise, it might cause damage to this product.
• Do not randomly damage the electric plug and electric line. If the electric line or electric plug is damaged, please do not use it any longer or attempt to repair it yourself; it must be repaired by a professional person, otherwise, it might trigger short-circuit, electric shock, or fire.
• If the power cord is not long enough, please do not use an extension cord.
• The stove or lighted cigarette is not allowed to be placed next to the toilet pan; cigarette butts, etc., are not allowed to be thrown into the toilet pan.
• Do not block the air openings of the product. Keep the air openings free of lint, hair, and the like.
• Do not use while bathing.

Shower Room Installation Precautions

⚠️ WARNING: When using in a shower room, please install air exchange equipment to ensure the air in the shower room is not too moist. This product is electric; it is not allowed to install it in a place that is easily high-wet or easily splashed by water, otherwise, it might trigger electric shock or fire.

Please ensure to cut off the electric power before washing this product. Do not use water to directly wash this product, otherwise, it might trigger electric shock or fire.

Please put and use this product in the shade; do not place it directly beneath the sun, otherwise, it might cause color fading or burn the surface of the product due to temperature instability.

Do not use industrial water, wastewater, seawater, reclaimed water, and other sewage, otherwise, it may cause skin inflammation and other problems.

Persons (including children) with physical, perceptual, intellectual disabilities, or lack of experience and common sense need to use the product under the guidance or supervision of someone else, or they may cause electric shock, injury, or fire.

Electrical Plug Placement: Please notice the assembly location of the electric wiring plug. The electric plug should be a water-proof plug. The assembly location of the electric plug must be over 0.5m (19.7in) above the floor and far away from the shower or bathtub, otherwise, it might cause electricity leakage.

Hose Assemblies: When installing this product, please remove the old hose assemblies owned by users and install them with new hose assemblies. Do not reuse the old hose assemblies to avoid related safety problems.

Grounding: The grounding wire of this product must conform to the stipulated construction mode, and the three-level grounding structure must be grounded, otherwise, the use of this product is prohibited.

Electrical Connection: Electric plugs need to be plugged into the electric supply with an air switch.

Water Shut-off Valve: In the same room where this product is installed, a switch for the water inlet angle valve needs to be installed within reach. It is used in emergency situations to cut off the waterway of this product without the aid of tools; otherwise, unexpected failures of this product may occur and will cause user loss.

Long Periods of Non-Use: If you have not used this product for a long time, please close the angle valve, press the water release button to drain the water from the ceramic itself, and cut off the power. When using the product again, please wash first to prevent water quality problems and skin diseases.

Freezing Prevention: When the outside air temperature is lower than 0°C, in order to prevent water leakage caused by external filters and other accessories likely freezing, please be sure to close the water inlet valve and drain the left water. If a pipe has been frozen, please raise the room temperature and wait for the pipe to normalize before using the toilet, otherwise, the product may not be used normally.

Component List

The following components are included with the SMART TOILET:

• SMART TOILET: The main toilet unit.
• REMOTE CONTROL: For operating the smart toilet functions.
• SCREWS & EXPANSION NUTS (2pcs): For mounting the remote control holder.
• TWO 7TH BATTERY: For the remote control.
• USER MANUAL: This instruction manual.
• SEALING RING: Used to create a watertight seal during installation.
• INLET VALVE: Connects the water supply to the toilet.
• FILTER: Filters the incoming water.
• TEFLON TAPE: For sealing pipe threads.
• 15/16-14UNS ADAPTER: For connecting different pipe sizes.

ⓘ Note: Illustrations of these components are provided in the original document for visual reference.

Specifications

※1: Rated power: Set the water volume, seat temperature and water temperature to the highest level under the conditions of ambient temperature 68°F±41°F, inlet water static pressure 0.18MPa±0.02MPa, and inlet water temperature 59°F±33°F. Turn on the bidet function, and test the average power within 60 seconds after the temperature of the outlet water stabilizes.

※2: Maximum power: Set the water volume, seat temperature, and water temperature to the highest level under the conditions of an ambient temperature of 73°F±35°F, an inlet static pressure of 0.18MPa±0.02MPa, and an inlet temperature of 41°F±33°F. Turn on the bidet function and continue to work stably at the maximum power for a cleaning cycle.

※3: Water consumption test: Test the water consumption separately under the water pressure 0.16Mpa and 0.55Mpa three times. Get six values in total, then divide the sum by six and the average is the nominal water consumption.

Parts Names

Identify the components of the Smart Toilet:

• Lid: The top cover of the toilet seat.
• Seat: The main seating ring.
• Photosensitive induction window: Sensor for automatic lid opening/closing.
• Power led: Indicator light for power status.
• Side button: Button on the side of the toilet for basic functions.
• Flush button: Button for flushing.
• Type-C interface: Port for power connection (e.g., power bank).
• Knob: Control knob on the side for various functions.
• Rear wash hole: Outlet for posterior cleaning spray.
• Bidet wash holes: Outlet for feminine cleaning spray.
• Warm wind baffle: Directs warm air for drying.
• Spraying wand baffle: Guides the spray wand.
• Nozzle: The spray head for washing functions.
• Ceramic toilet: The main ceramic body of the toilet.
• Foot sensor: Sensor activated by foot for flushing or other functions.

Control Panel Indicators

The display panel shows indicators for:

• Power indicator: Shows power status.
• Seat temp status indicator: Indicates seat temperature status.
• Flushing status indicator: Shows flushing status.
• Water temp indicator: Displays water temperature.
• Seat temp indicator: Displays seat temperature.

ⓘ Note: After restarting the toilet, press the “DRY” button within two minutes on the remote control to switch the temperature measurement unit on the toilet display.

Product Drawings

The smart toilet has the following approximate dimensions:

• Length: About 680mm (26.8 in)
• Width: About 390mm (15.4 in)
• Height: About 443mm (17.4 in)

Power and Water Supply Connection

Ensure a proper connection to the power and water supply.

⬆️ Connect to grounded outlet

⚠️ Caution electric shock!

ⓘ If the power cord is not long enough, please use an extension line made by certificated manufacturers.

ⓘ Only for reference.

Installation Precaution

We reserve the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!

We shall not be liable for any injuries or property damages in connection with this product during installation or use of the product!

The product must be installed by a fully insured and licensed plumber only. Installation of the product by anyone other than a fully insured and licensed plumber shall void the limited warranty. We recommend that the licensed plumber have experience in the installation of the product.

During unpacking the product and prior to installation, inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged.

Installation Tools

The following tools are recommended for installation:

• Hammer Drill
• Caulking Gun
• Tape Measure
• Adjustable Wrench
• Pliers
• Torpedo Level
• Steel saw
• Knife
• Screwdriver
• Pencil

Product Installation

1. Install the water inlet valve

Clean the ground and dry the area before installation. Mark the central lines of the draining outlet, and install the inlet valve on the wall.

⬆️ Connect to grounded outlet

⚠️ Caution electric shock!

2. Mark the curve of ceramics

Align the drain hole of the ceramic with the central line. Mark the curve of the ceramics for later installation. Apply silicone sealant along the outline.

3. Toilet installation (Method 1)

① Sealing ring installation

Gently tilt the toilet sideways until it rests on its side surface. Install the sealing ring evenly along the outlet, with the small end of the sealing ring facing the toilet. Glue the edge of the toilet bottom with silicone sealant, then place the toilet base along the outline and position it.

② Toilet (ceramic) installation

Lift the toilet, use the floor drain as a reference, align the ceramic body of the toilet with the ceramic contour line drawn on the ground, and slowly place the ceramic on the ground so that the two marks overlap. After overlapping, press the ceramic down (can be pressed by the weight of the human body) so that the sealing ring fully contacts the ground.

ⓘ Do not move the ceramic or shake it left and right after the marks are overlapped, otherwise, the seal produced by the sealing ring may be damaged and cause water leakage.

4. Toilet installation (Method 2)

① Remove the bidet seat

Remove the fixing screws of the toilet; remove the connecting pipes and wires of the toilet, and separate the bidet seat from the toilet.

② Sealing ring installation

Place the sealing ring onto the flange.

③ Ceramic installation

Glue the edge of the toilet bottom with silicone sealant. Line up the toilet base over the flange screws. Place the toilet base and secure the flange bolts. Glue the edge of the toilet bottom with silicone sealant, place the toilet base along the outline and position the toilet base.

④ Bidet seat installation

Adjust the bidet seat to match the toilet, use screws to fix the bidet seat on the toilet.

5. Connect the water inlet valve and filter

As shown in the following figures.

NOTE: Do not use the smart toilet immediately after installation; use it after 48 hours.

1. Install the part A water inlet valve.
2. Connect part B and part C to the part A water inlet valve.
3. Connect part D filter to the part A water inlet valve, and connect part E water inlet hose to the part D filter.
4. Finished, connect to the power.

6. Connect to the power

Only connect this product to a properly grounded outlet.

7. Using the product for the first time

1. Connect to the power and open the water inlet valve. Check every function button of the remote control and side control, such as rear/bidet wash, dry, flow adjustment, water temp adjustment, massage cleaning, swing cleaning, LED, seat temp adjustment, etc.
2. Rear/Bidet wash performance test: Touch the seat sensor built-in the seat with hand to activate the smart toilet and at the same time press the Rear/Bidet button to check if the Rear/Bidet wash functions work properly.

Instructions for Remote Control Installation

Method 1: Using Double-Sided Tape

1. Remove the double-sided adhesive surface on the back of the remote control holder.
2. Clean dust, grease, and water droplets on the walls and wipe them clean.
3. Press the remote control fixed seat with double-sided tape onto the wall. Press it evenly for 3 to 5 minutes.

Note: This method is applicable to glazed tiles, glass, and smooth walls.

Method 2: Using Screws

1. Make two holes in the wall with a drill bit.

Note: The position of the hole shall be suitable for the user to access the remote control conveniently when sitting on the seat.

2. Insert the expansion plugs into the holes on the wall, then align the fixing holes of the remote control holder and lock the bolts.

Put the remote control on the fixed base after installing the battery.

Tips:

• Please place the remote control on the holder after each use. Do not let the remote control fall on hard ground, otherwise, it would cause malfunction or damage to the remote.
• Do not spill water on the remote control or drop it into water, otherwise, it would cause malfunction or damage to the remote.

Remote Control Panel Overview

The remote control panel includes the following functions:

• Posterior wash (REAR/SWING): For rear cleaning.
• Feminine wash (BIDET/SWING): For feminine cleaning.
• Stop: Stops all current functions.
• Dry (DRY): Activates the air drying function.
• Flush (FLUSH): Initiates the toilet flush.

Additional controls and indicators include:

• Nozzle position: Adjusts the spray nozzle position.
• Self-cleaning: Initiates self-cleaning of the nozzle.
• Massage: Activates massage function.
• Eco: Enters energy-saving mode.
• Seat temperature adjustment: Adjusts seat heating.
• Wind temperature adjustment: Adjusts drying air temperature.
• Water Flow Adjustment: Adjusts water spray intensity.

Remote control to code:

To pair the remote control:

1. Leave the seat in its state. Long press the knob on the side of the fuselage for 3 seconds until a drop sound is heard.
2. Long press the remote control's 'woman wash + drying' key to enter the code mode.
3. Press the water temperature key to select the code value.
4. Press the stop key, then long press to confirm. The code pairing is successful.

The code pairing should be completed within 2 minutes. The code cannot be matched after success.

TIPS: Please keep sitting and make sure the seat sensor is activated before operating the smart toilet by remote or side control.

Using Instructions

STOP

Press the button; all functions stop.

REAR / SWING

Short Press the button to activate the posterior wash function. It will stop after 2 minutes automatically or by pressing the stop button. This function will also stop when the user leaves. Under Posterior/Feminine wash mode, Long Press the button to activate the swing function. The nozzle sprays back and forth automatically. Press the button again to stop.

BIDET/SWING

Short Press the button to activate the feminine wash function. It will stop after 2 minutes automatically or by pressing the stop button. This function will also stop when the user leaves. Under Posterior/Feminine wash mode, Long Press the button to activate the swing function. The nozzle sprays back and forth automatically. Press the button again to stop.

DRY

Press the button to activate the drying function.

FLUSH

Press the button to flush the toilet.

POSITION

Under posterior wash or feminine wash mode, pressing the > button moves the spray position forward; pressing the < button moves the spray position backward. The spray position is 3 levels adjustable; the initial level is 2nd. Different levels have corresponding indicators.

SELF-CLEANING FUNCTION

Press the "Self-cleaning" button; the spray arm can be retracted back and forth to clean itself.

MASSAGE

Under Posterior/Feminine wash mode, you can activate the massage function.

1. Impulse massage: The nozzle sprays with impulse water flow to clean the body.
2. High pressure massage: The nozzle sprays with high pressure water flow to clean the body.

※ Massage loop control: Impulse massage → High pressure massage → Stop.

ECO

Press the button to enter energy saving mode. Under energy saving mode, seat temperature is low (level 1); the night light turns off, and only the power indicator turns on.

※ Energy saving mode will resume the seat temperature and display when used.

※ Energy saving mode will be restored when the user leaves.

SEAT TEMPERATURE ADJUSTMENT

Every time you press the button, the seat temperature will be adjusted by one level. There are 3 levels that are cyclically adjustable, plus an off setting.

WIND TEMPERATURE ADJUSTMENT

In the drying state, every time you press the button, the air temperature will be adjusted by one level. There are 3 levels that are cyclically adjustable.

WATER TEMPERATURE ADJUSTMENT

Under posterior wash or feminine wash mode, each time you press the "water temperature" button, the water temperature is adjusted by one level. There are 3 levels that can be cyclically adjusted, plus a normal temperature setting (long press the "water temperature" button to enter the normal temperature). The default setting is level 2, and the corresponding level indicator light is on.

FLOW ADJUSTMENT

Under posterior wash or feminine wash mode, pressing the '+' button increases the water flow, and pressing the '-' button decreases the water flow. The flow is 3 levels adjustable; the initial level is 2nd. Different levels have corresponding indicators.

COMBINATION FUNCTION KEYS

• Stop + Self-cleaning: Long press for 5 seconds to manually clean the spray bar.
• Stop + Bidet wash: Long press for 5 seconds to activate or deactivate the night light function.
• Stop + Massage: Long press for 5 seconds to activate or deactivate the kick flip function (some models do not have this function).
• Flush + Rear wash: Long press for 5 seconds to activate or deactivate the Pre-wetting function (some models do not have this function).

Side Knob Control Instruction

The side knob offers convenient control. No need to reset the side knob after each use.

User Sitting

• Bidet wash: Twist the side knob forward; the spray wand extends, and bidet wash works for about 2 minutes.
• Rear wash: Twist the side knob backward; the spray bar extends, and rear wash works for about 2 minutes.
• Nozzle position: Under bidet/rear wash, twist the side knob forward or backward to adjust the nozzle position.
• Stop: Under bidet/rear wash, press the side knob to stop washing.
• Drying: Press and hold the side knob for 2 seconds to start air drying.
• Wind temp: Twist the side knob forward to increase the wind temp, backward to decrease the wind temp.
• Flush: Press the side knob to flush the toilet.

User Standing

• Press the side knob to flush the toilet.

Kick sensing

When the lid and seat ring are closed, touch the kick sensor lightly to open the lid automatically. When the lid is open and the seat ring is closed, touch the kick sensor lightly to open the seat ring automatically. When the lid and seat ring are open, touch the kick sensor lightly to achieve automatic flushing.

Motion sensing

When the lid and seat are closed, the lid will be automatically opened by approaching the toilet. When the lid or seat is opened and the seat sensor is activated, after about 90 seconds, the lid and the seat will automatically close when the user leaves. When the lid or seat is opened and the seat sensor is not activated, after about 150 seconds, the lid and the seat will automatically close when the user leaves.

Side button description

Drying on/off:

Press and hold '+' or '-' for about 2 seconds to turn on or off the drying in the seating state and non-rinsing state.

Air temperature adjustment:

In the drying state, short press '+' or '-' to adjust the air temperature.

Seat temperature adjustment:

In the non-flushing and non-drying state, short press '+' or '-' to adjust the seat temperature.

Water temperature adjustment:

Press '+' or '-' in the flushing state to adjust the water temperature.

Flushing function:

Short press the flushing button to start the flushing.

Night light function:

Press and hold the '-' for about 5 seconds to turn on or off the night light function when you are not seated.

Auto off seat flushing:

Press the flushing and '-' at the same time for about 5 seconds in the non-sitting state to open or close the automatic flushing function of leaving the seat.

Foot sensing flush:

Press the flushing and '+' at the same time for about 5 seconds in the non-sitting state to turn on or off the foot sensing flush.

Power-off flushing function:

When the power is off, connect to the USB Type-C with a power bank to achieve the manual, foot sensing, and off seat flushing functions (please do not cut off the power when flushing).

Maintenance and Cleaning

Maintenance and cleaning of toilet lid and seat

1. Turn off the power, close the water outlet valve.
2. Use a soft cloth to clean the lid and seat. ⓘ Be careful not to allow water to get inside or leave detergent in the gap between the top unit and the bowl unit. ⓘ Avoid using materials that will damage the surface. Clean the surface with a soft and wet cloth. ⓘ Corrosive chemicals or cosmetics (such as cleaners containing abrasive compounds and aftershave) cannot be used to clean the lid and seat.
3. Turn on the power, open the water outlet valve.

Maintenance and cleaning of the toilet bowl

1. Turn off the power.
2. Use a toilet brush and toilet detergent to clean the bowl. ⓘ Corrosive chemicals (such as cleaners containing abrasive compounds and strongly acidic cleaners or strong alkaline cleaners) should not be used to clean the bowl. ⓘ Wire brush or abrasive nylon scrubbing brush should not be used to clean the bowl.
3. Turn on the power.

Cleaning The Water Filter

1. Turn off the power. Close the water outlet valve.
2. Remove the water-inflow filter from the inlet hose.
3. Take out the filter by using a flat-blade screwdriver to unscrew the filter.
4. Remove the filter and rinse it with clean water.
5. Install the filter screen as it is. Be sure to tighten it; otherwise, it will cause water leakage.

How to do?

This section addresses common operational issues.

1. When the toilet cannot flush automatically due to power outage.

Connect the smart toilet with a power bank through the TPYE-C interface.

2. When the toilet cannot flush automatically due to water outage.

1. Flush the sewage in the toilet away with a basin.
2. After flushing, add water to the toilet to avoid stinking.

3. When the product is left unused for long time

1. Turn off the power, and close the tee valve, drain the water in the inlet hose.
2. Especially in winter, the water inside the hose of the toilet should be discharged to avoid freezing.

Trouble Shooting

※ Notice: When encountering a problem, please read the above common troubleshooting carefully, and follow the solution instructions for product maintenance; Please contact professional maintenance personnel or dealers in time to seek help. There may be differences between the contents of this manual and the actual product, and the actual product shall prevail.

Maintenance Service Sheet

This section provides warranty and service information.

Free maintain regulation:

1. We warrant our products to be free from defects in materials and workmanship during normal use when properly installed and serviced, for a period of three (3) years from the date of purchase. This limited warranty is extended only to the ORIGINAL PURCHASER of the product and is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the product. This warranty applies only to our product purchased and installed in USA and Canada.
2. The obligations under this warranty are limited to repair, replacement, or other appropriate adjustment, at our option, of the product or parts found to be defective in normal use, provided that such product was properly installed, used, and serviced in accordance with instructions. We reserve the right to make such inspections as may be necessary in order to determine the cause of the defect.
3. This warranty does not apply to the following items:
• a) Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.
• b) Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, improper care, or maintenance of the product.
• c) Damage or loss resulting from sediments or foreign matter contained in a water system.
• d) Damage or loss resulting from the quality of water in the region where the product is used.
• e) Damage or loss resulting from improper installation or from installation of the product in a harsh and/or hazardous environment, or improper removal, repair, or modification of the product.
• f) Damage or loss resulting from electrical surges or lightning strikes or other acts which are not the fault of the product or which the product is not specified to tolerate, including failure to use the factory-equipped cord and plug, or use of a loose or faulty electrical outlet, or use of a current or socket other than a 120V, 60Hz electrical current from a GFI (ground, fused) socket.
• g) Damage or loss resulting from normal and customary wear and tear, such as gloss reduction, scratching, or fading over time due to use, cleaning practices, or water or atmospheric conditions, including but not limited to, the use of bleach, alkali, acid cleaners, dry (powder) cleaners, or any other abrasive cleaners, or the use of metal or nylon scrubbers.

Executive standard: CONFORMS TO UL STD. 1431/UL STD. 1591 ASME A112.4.2-2021

Warranty period: within three years from the purchase date

Due to the constant improvement of our products, we will keep the final interpretation of product changes. If the products you bought exist differences from the instruction, please refer to the actual product.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Made in China

52200000-01 V1.0

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• -Reorient or relocate the receiving antenna.
• -Increase the separation between the equipment and receiver.
• -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• -Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.