ZOTAC ZBOX C1331 NANO User's Manual
Cover page: ZOTAC logo, ZBOX branding, and "USER'S MANUAL C1331 NANO" with a hexagonal pattern background.
Introduction and Disclaimer
No part of this manual, including the products and software described herein, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ZOTAC.
Products and corporate names mentioned in this manual may be registered trademarks or copyrights of their respective companies, and are used for identification purposes only. All trademarks are the property of their respective owners.
Every effort has been made to ensure that the contents of this manual are correct and up to date. However, the manufacturer makes no guarantee regarding the accuracy of its contents, and reserves the right to make changes without prior notice.
CAUTION: Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.
Product Specifications
Processor
- Intel Processor N5100 (quad core, 1.1 GHz up to 2.8 GHz)
Onboard Graphics
- Intel UHD Graphics
- HDMI 2.0b (max resolution: 3840x2160 @60Hz)
- DP 1.2 (max resolution: 4096×2160 @60Hz)
- VGA (max resolution: 1920×1080 @60Hz)
Memory Support
- 2 x DDR4-2933/2666 SO-DIMM slots
- Up to 16 GB of memory
USB Ports
- 2 x USB 3.1 ports
- 1 x USB 3.0 Type-C port
- 1 x USB 3.0 port
- 1 x USB 2.0 port
Storage Support
- SATA 6.0 Gb/s transfer rates
- Supports one 2.5-inch SATA HDD/SSD (9.5mm max height)
Network Support
- Dual Gigabit (10/100/1000Mbps) LAN
- IEEE 802.3 compatible
Wi-Fi Support
- 802.11ac Wi-Fi (dual-band)
- Bluetooth 5
Audio
- Digital 8 Channel Audio (LPCM/bitstream via HDMI)
Operating System Support
- Windows 10 64-bit (Preinstalled Windows 10 Pro for Windows version)
Product Dimensions
- 127.8mm x 126.8mm x 56.8mm
Safety Information
Your ZOTAC ZBOX nano is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions.
Setting Up Your System
- Read and follow all instructions in the documentation before operating your system.
- Do not use this product near water or a heat source such as a radiator.
- Set up the system on a stable surface with the provided stand. Never use the system alone without the stand.
- Openings on the chassis are for ventilation. Do not block or cover these openings. Make sure you leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation openings.
- Use this product in environments with ambient temperatures between 0°C and 35°C.
Care During Use
- Do not walk on the power cord or allow anything to rest on it.
- Do not spill water or any other liquids on your system.
- When the system is turned off, a small amount of electrical current still flows. Always unplug all power, modem, and network cables from the power outlets before cleaning the system.
- If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer:
- The power cord or plug is damaged.
- Liquid has been spilled into the system.
- The system does not function properly even if you follow the operating instructions.
- The system was dropped or the cabinet is damaged.
- The system performance changes.
Welcome
Congratulations on your purchase of the ZOTAC ZBOX nano. The following illustration displays the package contents of your new ZOTAC ZBOX nano. If any of the below items are damaged or missing, contact your retailer.
Package Contents
- 1 x ZOTAC ZBOX nano
- 1 x ZOTAC VESA mount
- 4 x Mount screws
- 1 x AC Adapter
- 1 x Power Cord
- 1 x WiFi antenna
- 1 x User Manual & Quick Start Guide
- 1 x OS Recovery USB Drive (Optional)
Note: If you use the Barebone version, please download the drivers on www.zotac.com.
Illustration of package contents: ZOTAC ZBOX nano mini PC, VESA mount, screws, AC adapter with power cable, WiFi antenna, Quick Start Guide, and OS Recovery USB Drive.
Getting to Know Your ZOTAC ZBOX nano
Front View
Image of the front panel of the ZOTAC ZBOX nano, showing numbered ports and indicators.
1. Power button
The power button turns the mini-PC ON and OFF.
2. Power LED
The Power LED is always ON when power is on.
3. SATA status LED
The SATA LED blinks when data is being written onto or read from the SATA.
4. Wi-Fi status indicator
The Wi-Fi LED is always ON when data is being transferred over Wi-Fi.
5. Memory card reader
The built-in memory card reader reads SD/SDHC/SDXC cards used in devices such as digital cameras, MP3 players, mobile phones, and PDAs.
6. Headphone/Audio Out jack
The stereo headphone jack (3.5mm) is used to connect the system's audio output signal to amplified speakers or headphones.
7. Microphone input
The microphone input is designed to connect a microphone for video conferencing, voice narrations, or simple audio recordings.
8. USB 3.0 Type-C port
The USB 3.0 Type-C port supports SuperSpeed USB 3.0 devices. Use the port for USB 3.0 devices for maximum performance with USB 3.0 compatible devices.
9. USB 3.0 port
The USB 3.0 port supports SuperSpeed USB 3.0 devices and is backwards compatible with USB 2.0/1.1 devices. Use the ports for USB 3.0 devices for maximum performance with USB 3.0 compatible devices.
Rear View
Image of the rear panel of the ZOTAC ZBOX nano, showing numbered ports.
1. WiFi antenna connector
The WiFi antenna connector supports the included WiFi antenna.
2. Ethernet ports
The eight-pin RJ-45 LAN port supports standard Ethernet cable for connections to local area networks (LAN) with speeds of 10/100/1000Mbps.
3. USB 3.1 port
The USB 3.1 port supports SuperSpeed USB 3.1 devices and is backwards compatible with USB 3.0/2.0/1.1 devices. Use this port for USB 3.1 devices for maximum performance with USB 3.1 compatible devices.
4. USB 2.0 port
The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mice, cameras, and hard disk drives.
5. HDMI port
The HDMI (High Definition Multimedia Interface) port supports a UHD device such as an LCD TV or monitor to allow viewing on a larger external display.
6. VGA port
The VGA port supports connection to analog monitors and displays.
7. DisplayPort
The DisplayPort supports both external (box-to-box) and internal (laptop LCD panel) display connections.
8. Power input (DC19V)
The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the PC. To prevent damage to the PC, always use the supplied power adapter.
The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body.
Customizing the ZOTAC ZBOX nano
Before installing hardware, please follow the instructions below to remove the cover of your ZOTAC ZBOX nano.
Step 1: Remove the four screws securing the bottom cover into place.
Image showing the bottom of the ZBOX nano with four screws visible.
Step 2: Remove the bottom cover.
Image showing a hand lifting the bottom cover off the ZBOX nano after the screws have been removed.
Installing Hardware
Installing a Memory Module
1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot at a 45-degree angle.
Image showing a hand inserting a SO-DIMM memory module into a slot inside the ZBOX nano at a 45-degree angle.
2. Gently press down on the memory module until it locks into place by the arms of the memory slot.
Image showing a hand pressing down on the memory module to secure it into the slot.
Installing a Hard Disk Drive
1. Locate the hard disk bracket, remove the screws, and remove the hard disk bracket as shown in the image below.
Image showing a screwdriver being used to remove screws from the hard disk bracket inside the ZBOX nano.
2. Install the hard disk bracket onto a 2.5-inch SATA hard disk drive /SSD with 2 screws.
Image showing a 2.5-inch SATA hard disk drive/SSD with a hard disk bracket being attached using screws.
3. Insert the hard disk drive /SSD into the socket and gently slide into the connector.
Image showing a hand inserting the hard disk drive/SSD with bracket into the ZBOX nano's connector.
4. Reinstall the screw for the hard disk bracket.
Image showing a screwdriver being used to reinstall the screw for the hard disk bracket.
5. If you use a 9.5mm hard disk drive, please use the default sticked foil. If you use a 7mm hard drive or SSD, please stick one more thicker foil on the default foil.
Images illustrating the use of foil pads for different drive thicknesses.
Setting Up Your ZOTAC ZBOX nano
Please connect your peripherals before using your ZOTAC ZBOX nano.
Illustration showing the ZOTAC ZBOX nano rear panel with numbered ports, and corresponding numbered cables/connectors below: 1. WiFi antenna, 2. Network cable (RJ-45), 3. USB 3.1 device, 4. USB 2.0 device, 5. HDMI cable, 6. DisplayPort cable, 7. VGA cable, 8. Power adapter.
1. Connecting the WiFi antenna
Connect the WiFi antenna to the WiFi antenna connector.
2. Connecting to a network device
Connect one end of a network cable to the LAN port on the system rear panel and the other end to a network hub, switch, or router.
3. Connecting to USB 3.1 devices
Connect USB 3.1 devices such as external hard disk drives, SSDs, and flash drives to the USB 3.1 port on the system rear panel.
4. Connecting to USB 2.0 devices
Connect USB 2.0 devices such as keyboards, mice, cameras, and hard disk drives.
5. Connecting to an HDMI display
Connect one end of an HDMI cable to an HDTV or monitor, and the other end to the HDMI port on the system rear panel.
6. Connecting a DisplayPort display
Connect the DisplayPort connector to the DP port of the monitor or display.
7. Connecting a VGA display
Connect the VGA connector to the VGA port.
8. Connecting the power adapter and turning on the ZBOX nano
Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press the power switch on the front panel to turn on the system.
When your ZOTAC ZBOX nano is not in use, unplug the power adapter or switch off the AC outlet to conserve power.
Positioning the ZOTAC ZBOX nano
- Do not position the ZOTAC ZBOX nano where the ventilation holes are covered. To guarantee proper use, leave 4 inches (10 cm) of spacing in front of the ventilation holes.
- ZOTAC ZBOX nano mini-PC systems provide ample connectivity in a tiny form factor; please choose connectors and cables in appropriate sizes to avoid interference.
Mounting the ZOTAC ZBOX nano to an LCD monitor
You can attach your ZOTAC ZBOX nano to the back of a VESA75/100 compliant monitor.
1. Secure the VESA mount to the LCD monitor using 4 screws (not included).
Image showing the VESA mount.
Disclaimer: ZOTAC cannot be held liable for damages resulting from an improper installation.
2. Align the ZOTAC ZBOX nano mounting holes to the VESA mount attachment pegs. Attach the ZOTAC ZBOX nano to the VESA mount and gently press down to secure the ZBOX to the mount.
Image showing the ZOTAC ZBOX nano being aligned and attached to the VESA mount.
3. Connect the ZOTAC ZBOX nano to your LCD monitor with a VGA/HDMI/DP cable.
Image showing the ZOTAC ZBOX nano mounted on the back of an LCD monitor, connected via a display cable.
Installing Drivers and Software
Installing an Operating System
Depending on the ZOTAC ZBOX nano model, the system may not ship with an operating system pre-installed. The user must install the operating system before the ZOTAC ZBOX nano can be used. The following operating systems are supported:
- Windows 10 64-bit
Follow the instructions below to install an operating system:
- Attach an external DVD drive (not included) to an available USB port.
- Insert the operating system installation disk (not included) into the DVD drive.
- Wait for the ZOTAC ZBOX nano to boot from the disk.
- Follow the onscreen directions to install the operating system.
- Install system drivers to gain full functionality of the ZOTAC ZBOX nano hardware and features.
Installing System Drivers
Before you can use the full features of the ZOTAC ZBOX nano, the system drivers must be installed. The following types of operating systems are supported by the USB flash drive:
- Windows 10 64-bit
Follow the instructions below to install the system drivers:
- Insert the driver USB flash drive. If autorun is enabled, the driver installation main menu will show up automatically. If autorun is disabled, you may click the file Launch.EXE to bring up the driver installation main menu.
- The following drivers are available on the USB flash drive:
- Intel Chipset Driver
- Intel Graphics Driver
- Realtek Ethernet PCI-E Driver
- Wireless Network Driver
- Bluetooth Driver
- Intel Management Engine
- Intel SerialIO
- Intel GNA Driver
Each driver must be installed individually to ensure proper operation of the ZOTAC ZBOX nano.
- Select the driver you want to install. The driver installer should launch.
- Follow the onscreen instructions to install the drivers.
- Restart the system.
Screenshot of the ZOTAC ZBOX nano driver installation menu from a USB flash drive, listing various drivers.
Using Your ZOTAC ZBOX nano
Configuring a Wireless Connection
Please follow the instructions below to connect to a wireless network:
- Double-click the wireless network icon (pic) in the notification area.
- Select the wireless network you want to connect to from the list and click Connect.
- After connection is established, you will see "Connected."
Note 1: For security concerns, Do NOT connect to an unsecured network, otherwise, the transmitted information without encryption might be visible to others.
Note 2: Enter the network security key if necessary.
Screenshot of the Windows notification area showing the wireless network icon and a dialog box for connecting to a wireless network.
Configuring Audio Output
Follow the steps below to enable audio output when connecting the ZOTAC ZBOX nano to a TV or receiver via DP/HDMI adapter.
- Access the Sound settings via the system Control Panel.
- Under Playback devices, click the display device that corresponds with your audio compatible display.
- Click the "Set Default" button in the lower right hand corner.
- Click "OK" to exit the setup.
Screenshot of the Windows Sound control panel, showing playback devices, with an audio device selected as default.
