Comfee Cooker Hood

Recommendations and Suggestions

The instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

Installation

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing.
• Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account. The distance of 65 cm can be reduced for non-combustible parts of range hoods, and parts operating at safety extra low voltage, provided these parts do not give access to live parts if deformed.
• Regulations concerning the discharge of air have to be fulfilled.
• This appliance is for indoor household use only.
• To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.
• Please unplug before cleaning and maintenance the appliance. Use a soft cloth moistened with mild soap, and then use a dry cloth to wipe it again.

Use

The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.

• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Do not flame under the range hood.

CAUTION: Accessible parts may become hot when used with cooking appliances.

Extension sockets are forbidden.

Please cut off the power before maintenance.

This appliance has been designed for home use only, and may cause danger if used in special occasions.

Maintenance

The cooker hood and its filter should be cleaned regularly according to the instruction.

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean the hood using a damp cloth and a neutral liquid detergent.
• The appliance uses 4 hob elements at most.

The symbol ♻️ (recycling symbol) on the packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Components

Product Components

Documentation

Installation Components

Diagrams show the various components and their assembly.

Dimensions

Unit: mm

Diagrams show the overall dimensions of the cooker hood, including width (598/898 mm), depth (448 mm), height (448 mm), and chimney dimensions. Minimum clearance from the hob is indicated as 650 mm.

Installation: Wall Drilling and Bracket Fixing

Follow these steps for wall mounting:

• Draw a vertical line up to the ceiling or upper limit in the center of the area where the hood will be fitted.
• Draw a horizontal line A at 835-935 mm above the cooker top.
• Draw a horizontal line B at 940 mm above line A.
• Draw a horizontal line C at 116 mm below line A.

Mark Points:

• Mark point (1) on line A, 80 mm from the vertical reference line. Repeat on the other side, ensuring marks are level.
• Mark point (2) on line B, 40 mm from the vertical reference line. Repeat on the other side, ensuring marks are level.
• Mark point (3) on line C, 155 mm from the vertical reference line. Repeat on the other side, ensuring marks are level.

Diagrams illustrate the line and point marking process.

Fix the brackets (Optional)

• Drill holes at the marked points with a 10 mm drill bit.
• Insert Wall Plugs 11 into the holes.
• Screw 2 screws 10 (5 x 50) into Wall Plugs 11 at horizontal line A. Approximately four-fifths of the screw length should be engaged for hooking the hood.
• Fix a Chimney fixing bracket 21 with 2 screws 10 (5x50) at horizontal line B.

Hook the hood body

• Hook the hood body to the 2 screws 10 (5 x 50) at horizontal line A.
• Level the hood body.
• Remove the filter from the inside of the hood body, then fix screws 10 to Wall Plugs 11 at points (3).

Diagrams show correct and incorrect hood hanging.

Connections: Ducted Version Air Exhaust System

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe of 150 mm or 120 mm diameter, as chosen by the installer.

• If installing a 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.
• Fix the pipe 4 in position using sufficient pipe clamps (not supplied).
• Remove possible charcoal filters.

Diagrams illustrate pipe connection options.

Chimney Assembly

The chimney can only be installed with the exhausting hood.

Lower Decorative Chimney

• Fix the Lower Decorative Chimney to the hood body with 2 screws 12 (4.2 x 9.5) supplied with the hood.

Upper Decorative Chimney

• Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood.

Diagrams show the chimney assembly process.

Use: Speed Adjustment (For some models)

Maintenance: Grease Filters

Cleaning Metal Self-Supporting Grease Filters

• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• Remove the filters one by one by pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood, make sure that they are completely dry. (The color of the filter surface may change throughout the time, but this has no influence on the filter efficiency).
• When fitting the filters into the hood, pay attention that they are mounted in the correct position, i.e., the handle facing outwards.

Activated Charcoal Filter (Recirculation Version)

These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage.

Replacing the Activated Charcoal Filter

• Remove the metal grease filters.
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.

Lighting: Light Replacement

For rectangular LED:

• Remove the grease filter.
• Remove the light by levering its fitting from the hood body (this may require pressure or force to be applied).
• Disconnect the connector of the light.
• Replace the light with a new one of the same type, making sure that you connect the light with the light cable correctly.
• Reconnect the power by inserting the mains plug or by switching on the fuse.

Trouble Shooting

Disposal of Old Electrical Appliances

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE) requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.

The crossed out "wheeled bin" symbol ?️ on the product reminds you of your obligation that when you dispose of the appliance, it must be separately collected.

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Technical Data

Data sheet for household cooker hoods in accordance with delegated regulation (EU) No. 65/2014 and regulation (EU) No. 66/2014.

Warranty Policy / Service

We congratulate you on your new device and are convinced that you will be satisfied and have your joy with this modern appliance.

However, if you recognize a reason for a complaint, please contact us:

Midea Europe GmbH
Ludwig-Erhard-Str. 14
65760 Eschborn

Phone: +49 6196-90 20 - 0
Fax: +49 6196-90 20 -120
Email: info-meg@midea.com
Homepage: www.midea.com/de

In case of service:
Phone: +49 6196-90 20 - 0
Fax.: +49 6196-90 20 -120
Email: service-meg@midea.com

In case of a technical fault, enter your exact address, telephone number, sales contract number and device type (from the type plate of the device). A precise fault description saves you time and money. For special questions, please contact the customer service center.

Before calling for service:

• Please check whether there is an operating error or a cause that has nothing to do with the function of your device.
• Please observe the note in the user manual and check whether:
  • The power plug is connected.
  • The power plug may be damaged.
  • Electricity is available.

Warranty terms

This device has been manufactured and tested according to the most modern methods. The seller warrants for faultless material and proper manufacture for a period of 24 months from the date of sale to the end user. The unit is not suitable for commercial use.

The claim under guarantee lapses in the event of intervention by the Buyer or by a third party. Damage caused as a result of improper handling or operation, incorrect installation or storage, improper connection or installation as well as an act of God or other external factors shall not be covered by this warranty.

When claims are submitted, the manufacturer reserves the right to make improvements to defective parts or to replace or exchange the device.

Only if it is not possible to achieve the intended use of the device by repairing or replacing the device, the buyer can demand a reduction of the purchase price or the cancellation of the purchase contract within 6 months from the date of purchase.

Claims for damages, including consequential damages, are excluded unless they are based on intent or gross negligence.

The guarantee claim exists only with submission of the product and the purchase receipt. This warranty is valid within Germany.

Importer by:
Midea Europe GmbH
Ludwig-Erhard-Str. 14
65760 Eschborn Germany

Disclaimer

The manufacturer shall decline all responsibility if the foregoing recommendations and instruction regarding installation, maintenance and use are not observed and respected when using the cooker hood.