SONOFF ZBMINI Extreme

Product Introduction

Diagram of the SONOFF ZBMINI Extreme device showing: a button, a green LED signal indicator, and wiring ports.

The device weight is less than 1kg, and the recommended installation height is less than 2m.

LED Indicator Status Instruction

Features

SONOFF Zigbee smart switch (No neutral required) allows you to remote control, schedule on/off and set smart scenes to trigger other devices, etc. by connecting a Zigbee hub.

• ? Remote Control
• ⏱️ Single/Countdown Timing
• ?️ Voice Control
• ⬆️ OTA Upgrade
• ? Smart Scene
• ? External Switch
• ⚡ Power on State
• ? Camera Linking

Note: Above functions are determined by the connected Zigbee Hub.

Installation

1. Power off

Diagram showing a hand turning off a circuit breaker with ON/OFF switches. Warning symbols are present.

⚠️ Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

2. Wiring Instruction

Before installing the device, please install an air switch as the protective device (Air switch: 10A/250V).

Diagram 1: Shows L Out, S1, S2, L In terminals. L In is connected to 100-240V AC live, N to neutral. L Out is connected to the load. S1 and S2 are for external switches.

Diagram 2: Similar to Diagram 1, showing different external switch configurations for S1 and S2.

Diagram 3: Shows L Out, S1, S2, L In terminals. L In is connected to 100-240V AC live, N to neutral. L Out is connected to the load. S1 and S2 are for external switches.

Diagram 4: Similar to Diagram 3, showing different external switch configurations for S1 and S2.

Note: For wiring methods ③ and ④, please ensure the proper wiring and powering of the L in terminal, otherwise it will cause the device to work abnormally.

Pairing

Pair with eWeLink App

1. Download the eWeLink App. Instructions to download the eWeLink App from Google Play or the App Store.

2. Pair SONOFF Zigbee Bridge to your eWeLink account.

3. Power on.

Diagram of the SONOFF ZBMINI Extreme device showing power connections. After powering on, the device will enter the pairing mode defaulted during the first use and the green LED indicator will "flash slowly".

Note: The device will exit the pairing mode if you do not operate it within 3 minutes. If you want to enter the pairing mode again, press and hold the button of the device for 5 seconds until the green LED indicator "flashes slowly" and releases.

Note: The device will remain off and cannot be controlled by the device's button or external switch when it is in pairing mode.

Add ZBMINI Extreme to the ZB Bridge

Description of eWeLink App interface showing adding a sub-device to the ZB Bridge. Steps involve tapping the "Add" icon and waiting for the device to be found.

Pair with Amazon Echo

1. Download the latest Amazon Alexa App and pair it with Amazon Echo with built-in Zigbee hub.

2. Power on ZBMINI Extreme, then it defaulted to enter the pairing mode and the green LED indicator "flashes slowly".

Diagram of the SONOFF ZBMINI Extreme device showing power connections.

Note: The device will remain off and cannot be controlled by the device's button or external switch when it is in pairing mode.

3. Ask the Alexa Echo to discover the devices automatically by saying "Alexa, discover my devices".

Note: If failed to pair within 3 minutes, ZBMINI Extreme will exit the pairing mode. Long press the button on ZBMINI Extreme for 5s to make it enter the pairing mode if you need to pair again.

Device Configuration

Switch the device to the corresponding switch

The device supports rocker switch by default. If you want to change the switch type, press the button 3 times and see the green LED indicator flash 3 times quickly, then the switch type is switched successfully.

Note: Please switch to the corresponding switch type before installing the device in the mounting box.

Install the ZBMINI Extreme in the mounting box

Diagram showing the SONOFF ZBMINI Extreme being installed inside a standard wall mounting box, connected to a wall switch.

Specifications

Troubleshooting & Reset

Factory reset

Return the device to its factory settings in any following ways (Device will enter the pairing mode automatically after resetting):

1. Press 10 consecutive times the connected external switch.
2. Long-press the device for 5s.
3. Delete the sub-device on eWeLink App.

Supported voice assistant

Logos for "works with Google Home", "works with Alexa", and "works with Alice" are displayed.

Warnings and Compliance

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

IC Warning

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le onjunc areil est conforme aux CNR d'l'innovation, la science et le développement économique Canada licables aux areils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: l'areil ne doit pas produire de brouillage, et; l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, onj si le brouillage est susceptible d'en compromettre le fonctionnement.

Declaration of Conformity

Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type ZBMINIL2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals

Operation frequency Range: 2405-2480MHz(Zigbee)

RF Output Power: 4.81dBm(Zigbee)

Company Information

Shenzhen Sonoff Technologies Co., Ltd.

3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China

ZIP code: 518000

Website: sonoff.tech

MADE IN CHINA

Certifications: FC, CE, WEEE symbol, Recycling symbol.