Wood & Hearts Swedish Wall

Scope of Application

The Wood & Hearts Swedish Wall is a versatile sports equipment designed for various exercises, promoting the development of coordination, balance, musculature, strength, and endurance. It is suitable for use by children under adult supervision. Incorrect assembly or use may lead to injuries. Please follow the instructions carefully for safe installation and use.

Recommended Age: 3 to 16 years old.

Maximum Load Capacity: 60 kg / 132 lbs.

Terms of Use

• Before assembly, check the completeness of the set and notify the manufacturer of any missing parts via the specified email address.
• For indoor use only.
• The product has no expiration term, but any damaged parts must be replaced immediately.
• Warranty: 2 years.
• Note: The warranty does not apply if the product is damaged due to weather conditions, as it is intended for indoor use only.
• The manufacturer reserves the right to make structural changes without prior notice, provided they do not affect functionality, safety, or key features.
• In case of inappropriate use or failure to comply with instructions, the manufacturer and seller bear no responsibility, and the warranty becomes void.
• Responsibility for any damage incurred by children during play rests with the supervising adults. If a child is injured, treat the wound and consult a doctor.

Safety Measures

• ⚠️ The product must be assembled by an adult. Do not attempt assembly without following the manufacturer's instructions, as improper assembly can lead to instability and danger.
• ⚠️ In its disassembled state, the product contains small parts that pose a choking hazard to children. After assembly, ensure all screws and fastenings are securely tightened. Keep spare screws out of children's reach.
• Limit the height of usage for small children by lowering the horizontal bar. A soft landing area is recommended for safety.
• Use only under the direct supervision of an adult. Never leave a child alone with the product.
• Tighten screws every 2 months and regularly check for signs of wear. Discontinue use immediately if any damage is found.
• Do not exceed the maximum weight limit. To prevent overcrowding and ensure stability, limit the number of children based on weight, size, and design.
• Do not use on uneven or sloping walls.
• Do not use if the product has visible damage or is improperly positioned.
• Do not use if the floor beneath is wet or contaminated.
• Position the product at least 2 meters away from hazards such as windows, sharp corners, or hard furniture. The area around the climber must be clear and safe.
• Do not place near heat sources or direct sunlight.
• Avoid modifying the ladder or adding homemade extensions unless you are certain they are safe and compatible, as modifications can affect stability and safety.
• Ensure children wear appropriate footwear with good grip, suitable for physical activity.
• Do not allow children to climb on the upper rail or horizontal bar.
• To ensure stability and prevent falls, the product must be securely attached to the wall.

Care and Maintenance

• To clean, wipe the item with a damp cloth or wet wipes.
• Avoid excessive moisture. Water can penetrate seams or microcracks and damage the wood. Wipe dry immediately if spills occur.
• Do not use abrasive sponges, aggressive detergents, alcohol, or acetone.
• Do not leave the product outdoors or near heat sources (radiators, fireplaces).
• For scratches or fading, you can restore a layer of varnish or paint using the same water-based product. Clean and lightly sand the surface before re-coating.
• If the product is not used for a long time, store it in a dry room with moderate humidity (40-60%). Avoid storage in damp or uninsulated areas.

Assembly Instructions

Parts List

Step 1: Assemble First Sidewall

Take stands 1 and 2 and attach the spacers (8) using screws (b) and the TORX T30 key (d).

Figure 1: Illustrates two side panels being formed by attaching spacers (8) to stands (1 and 2) using screws (b) and the TORX T30 key (d).

Step 2: Assemble Second Sidewall

Take stands 3 and 4 and attach them to spacers (8) using screws (b) and the TORX T30 key (d).

Figure 2: Shows the other two stands (3 and 4) being attached to spacers (8) in a similar manner to Figure 1.

Step 3: Attach Planks and Rods

Attach the planks (5) and rods (6) and sequentially connect them to the sidewalls assembled in Figures 1 and 2, using screws (a) and the TORX T30 key (d).

Figure 3: Depicts the planks (5) and rods (6) being attached to the previously assembled sidewalls using screws (a) and the TORX T30 key (d).

Step 4: Attach Mounting Planks

Attach the mounting planks (7) using screws (a) and the TORX T30 key (d).

Figure 4: Shows the mounting planks (7) being attached to the structure using screws (a) and the TORX T30 key (d). A close-up view highlights the attachment points.

Step 5: Mounting to a Brick or Concrete Wall

Attach the assembled construction to the brick or concrete wall using dowels (c) and screws (b).

Figure 5: Illustrates the Swedish wall structure being mounted to a solid wall (brick or concrete) using dowels (c) and screws (b).

Step 6: Mounting to a Stud or Drywall Frame

Attach the assembled construction exclusively to the wooden frame of the wall using screws (b).

Figure 6: Shows the Swedish wall structure being attached to a wooden frame or drywall structure using screws (b).

Possible Add-ons: Pull-Up Bar

Pull-Up Bar Parts List

Pull-Up Bar Assembly Step 1

Attach the left horizontal plank (3) to the inclined left plank (5) using screws (b) and key (d). Attach the left sidewall (1) to the inclined left plank (3) using screws (c).

Figure 1 (Pull-Up Bar): Shows the left horizontal plank (3) being attached to the inclined left plank (5) with screws (b) and key (d), and the left sidewall (1) attached to the inclined left plank (3) with screws (c).

Pull-Up Bar Assembly Step 2

Attach the inclined right plank (6) to the right horizontal plank (4) using screws (b) and key (d). Attach the right sidewall (2) to the right horizontal plank (4) using screws (c) and key (e).

Figure 2 (Pull-Up Bar): Shows the inclined right plank (6) attached to the right horizontal plank (4) with screws (b) and key (d), and the right sidewall (2) attached to the right horizontal plank (4) with screws (c) and key (e).

Pull-Up Bar Assembly Step 3

Insert the rods (7) into the grooves at the sidewalls, then join the received construction using screws (a, b) and key (d).

Figure 3 (Pull-Up Bar): Illustrates inserting rods (7) into the sidewall grooves and connecting the structure with screws (a, b) and key (d).

Other Accessories

The Swedish wall can be enhanced with various accessories, including:

• Rope with round platform
• Gymnastic rings
• Rope with spheres
• Rope ladder

Instructions on how to attach these accessories are provided visually in the manual.

Disposal and Environmental Information

Dispose of the product in accordance with local waste regulations. Components can be recycled where applicable.

Manufacturer & Contact Information

For manufacturer information, please check the product packaging.

Contact Information:

• Phone (USA, EN): +1 804-500-1025
• Phone (UA): +38 050 067 71 15
• Email: unterstutzung@woodandhearts.de
• Email: support.official@woodandhearts.com
• Website: woodandhearts.de
• Website: woodandhearts.com