Brief Installation Guide to Roller Washing Machine

Before Use

1. Before use, the foam base and the foam inside the machine must be removed, and the rear transport bolts and sleeves should be removed; otherwise, noise and malfunction will occur.
2. Do not connect any hot water source.
3. The water injection test should be carried out on the washing machine before delivery. Therefore, if there is some residual water in the drum, it is normal. It is recommended to run a quick empty-drum washing program before the first use.
4. Do not only wash a piece of clothing to prevent the unbalanced dewatering alarm.

Remove the Transport Bolts

There are a total of 4 transport bolts.

• 1. Remove the transport bolts.
• 2. Insert the bolts into the bolt holes and sleeve.
• 3. Take out bolts and sleeve.
• 4. Install the bolts, rubber mat cover.

Level the Washing Machine

1. Guarantee that the four bottom feet are in a tight state.
2. Press the two diagonal lines at the top of the washing machine to inspect whether the machine is wobbling.
3. Find out the foot that causes wobbling, and use a wrench to clockwise loosen the lock nut on the foot counterclockwise.
4. Rotate the adjustable foot to the appropriate height and inspect whether the machine is wobbling again.
5. After adjusting to the height, lock the lock nut to the bottom of the box clockwise.

Connect the Inlet Pipe

Please use a stop tap for the water connection.

• Screw the inlet hose nut onto the inlet valve connector, tighten the inlet hose nut and place.
• Screw the inlet hose nut onto the stop tap, tighten the nut, and turn the hose slightly leftwards and rightwards to confirm whether it is securely fastened in place.

Install the Drain Pipe

Hang the U-shaped support for the drain pipe on the water channel or drain pipeline, and fix the highest point of the drain pipe at the height of 70-125cm.

Control Unit

1. Press the Power button.
2. Select a cycle.
3. Select desired option function.
4. Press Start/Pause.
5. Press and hold for 3 seconds to power off.

Wi-Fi Connection

1. Open ConnectLife on your smartphone or tablet PC.
2. Bind your device on ConnectLife as follows:
   1. Click "Start here Add appliances" in "Home" page, or click "Add appliances" in "Devices" page, or click "+".
   2. Select "Washing Machine" or click "Scan QR/BAR code" or "Manual entry" below.
   3. Scan the QR/BAR code on the device or enter the AUID/SN manually. If you cannot find it, click for instructions.
   4. Click "SET UP APPLICATION".
   5. Read the instructions, operate the device into the Networking and Binding state, and click "NEXT".
   6. At this time, the app starts to search for devices, and you can select the device to be connected to the network from the search list; If it is not found, check your Bluetooth whether turn on. Bluetooth should be keep it on at all time. And then click "NEXT".
   7. Select your home Wi-Fi, enter the password, Then click the "CONNECT". The appliance will start networking and binding.
   8. After binding successfully, you can set the device name and room.
   9. Now, the device can be controlled remotely by APP.

When the "" display light on the display window is not on, you cannot remotely control the machine through the mobile phone. To enable this function, press the "0" button on the dashboard.

Washing Machine Maintenance

After the completion of washing

After the completion of washing program, please be sure to turn off the tap and unplug the power cord to avoid accidents.

Regularly clean the draining pump filter

Clean the draining pump filter at least three to five times every year. Tip: make sure that the water has cooled before operation to avoid burns.

• Inject 1 litre of water into the washing machine drum, check whether the filter is installed in place, whether water leakage exists, after confirmation, make the filter door return to its original position.
• Place the container door, pull out the drain pipe, unscrew pipe plug, and drain the water in the emergency container.
• Clean the filter, remove sundries in the inner cavity of the draining pump, and then install the filter by clockwise rotation.

Regularly clean inlet filter screen (please reserve the inlet filter screen)

In case of slow water supply or water supply failure, please check and clean the inlet filter screen in time. The specific operation is as follows:

• Unscrew the inlet pipe.
• Take out the filter screen.
• Clean the filter screen.
• Install the filter screen.
• Connect the inlet pipe.

Common Code and Solution

When the washing machine is not working normally and the display shows the following code, it may not be a fault. Please carry out the corresponding treatment according to the followings.