Tenda AC8 Gigabit Dual-Band Router - Quick Installation Guide
I. Set up the router
Diagram: A visual representation of the Tenda AC8 router with its ports and indicators. The diagram shows the WAN port (blue), LAN ports (yellow), power port, reset button, and WPS button. LED indicators for power, internet connection, and Wi-Fi are also depicted.
Steps:
- Connect the WAN port of the router to the broadband modem using an Ethernet cable.
- Connect your computer to one of the LAN ports using an Ethernet cable, or connect wirelessly using the default Wi-Fi name and password printed on the router's label.
- Connect the power adapter to the router and plug it into a power outlet.
- Press the power button to turn on the router.
II. Access the internet
Steps:
- Open a web browser on your connected computer or mobile device.
- Enter tendawifi.com or 192.168.0.1 in the address bar and press Enter.
- Follow the on-screen instructions to set up your internet connection. This may involve selecting your ISP type (e.g., PPPoE, Dynamic IP, Static IP) and entering your account information if required.
III. Connect to Wi-Fi
Steps:
- On your device, search for available Wi-Fi networks.
- Select the Wi-Fi network name (SSID) printed on the router's label.
- Enter the Wi-Fi password (also found on the router's label) to connect.
- You can change the Wi-Fi name and password during the internet setup process via the web interface.
LED Indicators
Diagram: A table detailing the function of each LED indicator on the router.
| LED | Status | Description |
|---|---|---|
| Power | Solid Green | Router is powered on. |
| Internet | Solid Green | Internet connection is established. |
| Internet | Flashing Green | Connecting to the internet. |
| Internet | Off | No internet connection. |
| WLAN | Solid Green | Wi-Fi is enabled. |
| WLAN | Flashing Green | Data is being transmitted wirelessly. |
| WLAN | Off | Wi-Fi is disabled. |
| LAN | Solid Green | Device connected to a LAN port. |
| LAN | Flashing Green | Data is being transmitted via LAN. |
| LAN | Off | No device connected to the LAN port. |
Ports & Buttons
Diagram: A visual representation of the router's ports and buttons.
- WAN Port: Connects to your modem.
- LAN Ports: Connect to wired devices.
- Power Port: Connect the power adapter.
- Reset Button: Resets the router to factory defaults (press and hold for 10 seconds).
- WPS Button: For quick Wi-Fi connection with WPS-enabled devices.
FAQ
- Q: What if I forget my Wi-Fi password?
A: You can reset the router to factory defaults by pressing and holding the reset button for 10 seconds. Then, you can set up the Wi-Fi again with a new password. - Q: How do I access the router's web interface?
A: Open a web browser and enter tendawifi.com or 192.168.0.1. - Q: My internet is not working. What should I do?
A: Check all cable connections. Ensure your modem is working correctly. Restart both your modem and the router. If the problem persists, contact your ISP.
Regulatory Information
FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Marking: This product complies with the essential requirements and other relevant provisions of applicable EU directives.
Troubleshooting
Issue: Cannot connect to the internet.
- Check if the WAN cable is securely connected.
- Verify that your modem is powered on and connected to the internet.
- Restart your modem and router.
- Ensure you have entered the correct PPPoE username and password if required by your ISP.
Issue: Slow Wi-Fi speed.
- Ensure the router is placed in a central location, away from obstructions.
- Change the Wi-Fi channel in the router's settings.
- Update the router's firmware.
