KEYENCE DX Series Handheld Terminal
Instruction Manual
Laser Classification
The DX Series is classified as below in accordance with IEC 60825-1.
| Item | DX-A600/A600GE/A400/A400GE/W600 |
|---|---|
| Wavelength | 655 nm |
| Output | 390 μW |
| Laser class | Class 1 laser product (IEC60825-1, FDA(CDRH) Part 1040.10*) |
* The laser classification for FDA (CDRH) is implemented based on IEC 60825-1 in accordance with the requirements of Laser Notice No. 56.
Symbols
The following symbols alert you to important messages. Be sure to read these messages carefully.
- [DANGER]: Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
- [WARNING]: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
- [CAUTION]: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
- [NOTICE]: Indicates a situation which, if not avoided, could result in product damage as well as property damage.
- [IMPORTANT]: Indicates cautions and limitations that must be followed during operation.
- [POINT]: Indicates additional information on proper operation.
- [REFERENCE]: Indicates tips for better understanding or useful information.
Safety Precautions on LED Product
The degree of risk of this product is shown below.
• LED product is classified as shown below according to IEC 62471.
- Exempt group: Does not pose any photobiological hazard.
- Risk Group 1 (Low-Risk): Does not pose a hazard due to normal behavioral limitations on exposure.
- Risk Group 2 (Moderate-Risk): Does not pose a hazard due to the aversion response to very bright light sources or due to thermal discomfort.
- Risk Group 3 (High-Risk): May pose a hazard even for momentary or brief exposure.
[WARNING]: Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyes.
Safety Precautions
General cautions
- Do not use this product for the purpose of protecting a human body or a part of a human body.
- This product is not intended for use as an explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive atmosphere.
- [DANGER]: Do not use this product in an application that may cause death, serious injury, or serious property damage due to a failure with this product occurring, such as nuclear power plants, on aircraft, trains, ships, or vehicles, used within medical equipment, playground equipment, roller coasters and other rides, etc.
- [WARNING]: If the product is used in a manner not specified by the manufacturer, the protection provided by the product may be impaired.
- Be sure to check that this product performs properly before starting the work or operation.
- [CAUTION]: We recommend that you take substantial safety measures to avoid any damage in the event of a problem occurring. Do not use this product in a manner not specified herein. Doing so may result in fire, electric shock, or malfunction.
- [WARNING]: Do not modify this product or use it in any way other than described in the specifications. Otherwise, the functions and performance cannot be guaranteed.
- [NOTICE]: Microscopic spots (black/bright spots), uneven brightness, or crosstalk (a phenomenon where non-existent lines or patterns are displayed) may occur on the LCD panel depending on the conditions.
- [NOTICE]: If the same display remains on the screen for a long time, afterimage may occur due to the characteristics of LCD.
Handling of DX Series
- Using batteries other than those specified by KEYENCE may cause fire or explosion. Be sure to use the specified battery.
- Use or store this product within the temperature range described in "Specifications" (page 3). Do not leave the product inside a closed car or at a place exposed to direct sunlight. Doing so may damage the unit or change its reading performance.
- Use within the humidity range described in "Specifications" (page 3). Do not use the product at locations where condensation occurs due to the rapid temperature change. Doing so may damage the unit.
- This is a precision instrument. Dropping this product or subjecting it to shock may cause damage. Be careful when carrying or using this unit.
- Do not place the DX Series in a location with high humidity or a dusty area. Doing so may damage the unit.
- Do not insert a sharp object such as a needle into the buzzer hole on the back side of the DX Series. The tarpaulin may be damaged.
Handling of main battery (DX-BP6/BP3) and communication unit with built-in main battery (DX-BS6/BS3/BQ6/BQ3)
Observe the following precautions during use. Failure to do so may result in heat generation, smoke generation, fire, explosion, battery leakage, gas leakage, etc. of the main battery pack.
- [WARNING]: Only use the specified battery.
- Do not charge, use, or store the main battery at locations of high temperature above the specified range—such as near fire, in a heated car, and under the scorching sun—or at locations of low temperature below the specified range.
- Do not put it into fire or subject to heat. If there is battery leakage or abnormal smell, immediately take it away from fire.
- Do not drop the main battery or subject it to strong pressure (such as by crushing, bending, deforming, making holes in, cutting, or throwing it).
Safety Precautions on Laser Product
The DX Series uses a visible semiconductor laser as a light source.
[WARNING]: Follow the instructions mentioned in this manual. Otherwise, injury to the human body (eyes and skin) may result.
- Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
- Do not disassemble this product. Laser emission from this product is not automatically stopped when it is disassembled.
- Do not stare into the direct or specularly reflected beam.
Precautions on Regulations and Standards
Precautions on wireless LAN
- [WARNING]: Remove the main battery of the DX Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker.
- Communication may be impossible at locations near metallic objects, locations surrounded with metallic walls, where there is a lot of metallic powder, and in similar usage environments. Be sure to check whether communication is possible prior to installation.
- If this product is used near devices with the same frequency band, radio wave interference may occur and the communication speed may become slow or communication may become impossible.
[Japan]
- Never disassemble or modify this device. Doing so is prohibited by the Radio Act. This device is specified radio equipment according to the Radio Act. Follow the criteria defined within this act to obtain construction design certification.
- This device may be used outdoors when communicating with registered stations in the 5.2 GHz band.
Electromagnetic display of technical standards compliance mark
This terminal complies with technical standards based on the Radio Act and Telecommunications Business Act of Japan. The mark indicating this compliance can be viewed as indicated below.
- DX-A600/A400: From the app list screen, Settings → About phone → Standard information
- DX-W600: From the Start menu (All apps), DX setup tool → About phone → Standard information
CE and UKCA Markings
KEYENCE Corporation has confirmed, on the basis of the following specifications, that this product complies with the essential requirements of the applicable EU Directive(s) and UK regulations. Be sure to consider the following specifications when using this product in the Member States of the European Union and in the United Kingdom.
- RE Directive (CE) and Radio Equipment Regulations (UKCA)
- RoHS Directive
- The full text of the EU declaration of conformity is available at the following internet address: http://www.keyence.com/cedoc
Frequency band of operation: Maximum radio-frequency power
| Model | WLAN | Bluetooth | NFC | WWAN |
|---|---|---|---|---|
| DX-W600 | 2400 to 2483.5 MHz: 20 dBm (100 mW) 5200 to 5690 MHz: 23 dBm (199.5 mW) | 2400 to 2483.5 MHz: 9 dBm (7.9 mW) | 13.56 MHz: 17 dBuA/m | - |
| DX-A600GE | 2400 to 2483.5 MHz: 20 dBm (100 mW) 5120 to 5350 MHz: 23 dBm (199.5 mW) | 2400 to 2483.5 MHz: 13 dBm (20 mW) | 13.56 MHz: -10 dBuA/m | WCDMA Band 1: 20.5 dBm (112.2 mW) Band 8: 24.5 dBm (281.8 mW) LTE Band 1: 20 dBm (100 mW) Band 3: 21 dBm (125.9 mW) Band 7: 20 dBm (100 mW) Band 8: 24 dBm (251.2 mW) Band 38: 24 dBm (251.2 mW) |
| DX-A400GE | 2400 to 2483.5 MHz: 17 dBm (50.1 mW) 5120 to 5350 MHz: 22 dBm (158.5 mW) | 2400 to 2483.5 MHz: 10 dBm (10 mW) | 13.56 MHz: -12 dBuA/m | WCDMA Band 1: 22.5 dBm (177.8 mW) Band 8: 24 dBm (251.2 mW) LTE Band 1: 22.5dBm (177.8 mW) Band 3: 24 dBm (251.2 mW) Band 7: 18.5 dBm (70.8 mW) Band 8: 24 dBm (251.2 mW) Band 38: 20.5 dBm (112.2 mW) |
Remarks: These specifications do not give any guarantee that the end-product with this product incorporated complies with the essential requirements of RE Directive and Radio Equipment Regulations. The manufacturer of the end-product is solely responsible for the compliance on the end-product itself according to this directive and these UK regulations.
The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
Countries/Regions: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, EL, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, RO, SK, SI, ES, SE, UK(NI), IS, LI, NO, CH, TR
UL certification
The DX Series complies with the following UL/CSA standards and has obtained the UL certifications.
- UL File No.: E167973
- UL category: AZOT/AZOT7
- Applicable standards: UL 62368-1, CAN/CSA-C22.2 No. 62368-1
Be sure to consider the following specifications when using this product as a UL certified product.
FCC Regulations
[CAUTION]: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Application regulation: FCC Part 15 Subpart B Class A, FCC Part 15 Subpart C, FCC Part 15 Subpart E
- 5150-5350MHz band is restricted to indoor operations only.
- Regulatory information page is located at: [settings]→[About phone]→[Regulatory]
[CAUTION]: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The product complies with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment should be installed and operated at least 10 mm away from your body.
ISED Regulations
This device complies with the following regulations specified by the ISED.
- Applicable regulation: CAN ICES-003 (A) / NMB-003 (A), RSS-247, RSS-102
- The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
- Operations in the 5250-5350 MHz band are restricted to indoor usage only.
- 5600-5650 MHz band is not allowed at Canada.
- Les dispositifs fonctionnant dans la bande de 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
- Les opérations dans la bande de 5250-5350 MHz sont limités à un usage intérieur seulement.
- La bande de 5600-5650 MHz n'est pas autorisée au Canada.
[CAUTION]: This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
This equipment should be installed and operated at least 10 mm away from your body.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.
Cet équipement doit être installé et utilisé à une distance d'au moins 10 mm de votre corps.
Precautions for Proper Use
Handling of packing
[NOTICE]: If units such as the DX-BS6 are not properly attached, the enclosure rating of the DX Series cannot be guaranteed. When using this product in environments where water or dust is present, check if these units are properly attached.
Dropping the DX Series or subjecting it to extreme shock may lead to the loss of water-proofing. Take adequate care when handling this product.
Unit Installation
As an example, the installation of the DX-BS6 is explained below.
- Insert the tip of the unit into the back of the main unit.
- Attach the unit to the main unit by using two fingers to push the two parts of the unit indicated with arrows until they click.
To remove the unit, press the tabs on the back of the main unit from the left and right, and then pull the unit up from the main unit.
[NOTICE]: If dirt or dust is attached, contact failure may occur on the unit connectors or charging/communication contact. This may cause charging function deterioration and instantaneous interruption. Make sure that textile waste is not attached to the unit connectors or charging/communication contact when cleaning.
Cleaning
Clean the following parts with compressed air periodically. If removing dirt is difficult, use a dry cotton swab to clean the unit connectors and charging/communication contact. (Use absolute ethanol if dirt is stuck on them.) When using an expansion unit, also clean its charging/communication contact.
Diagram description: Visuals showing unit connectors and charging/communication contact.
Checking the Package
When opening the package, check that the following items are all included. In the event of missing, defective, or damaged items, contact your nearest KEYENCE sales office.
- DX-A600/A600GE/A400/A400GE/W600 Main unit...1
- Instruction Manual...1
microSD / nano SIM card installation
The DX-A600/A400 has a microSD slot and a nano SIM slot. The DX-W600 has a microSD slot.
- Turn off the main unit and remove the main battery.
- Slide the desired slot cover in the direction of the arrow to unlock it, allowing the card to be inserted.
- Open the slot cover.
- For the DX-A600/A400, orient the card with its terminals at the bottom, and then place it in the slot. For the DX-W600, insert the card into the slot cover so the terminals are at the bottom when the slot cover is closed, as shown in the figure.
- Close the slot cover and lock it by sliding it in the direction of the arrow.
[NOTICE]: Even when not using a microSD or nano SIM card, be sure to close and lock the slot cover(s). The slot cover(s) may be damaged if unlocked.
Specifications
Main Units
| Model | DX-A600/A600GE | DX-A400/A400GE | DX-W600 |
|---|---|---|---|
| CPU | ARM® Penta Core | ARM® Penta Core | Intel® Quad Core + Scan processor |
| Controller | Android 10 | Android 10 | Windows® 10 IoT Enterprise |
| Main memory | 3 GB RAM, 16 GB ROM | 3 GB RAM, 16 GB ROM | 4 GB RAM, 64 GB ROM |
| Internal memory | - | - | - |
| LCD | 6.0-inch, 720 x 1440 | 4.0-inch, 480 x 800 | 6.0-inch, 720 x 1440 |
| Operation confirmation LED | 3-color LED | 3-color LED | 3-color LED |
| Trigger keys x 2, volume up and down keys, power key, side Fn keys x 2 | Trigger keys x 2, volume up and down keys, power key, front Fn keys x 3 | Trigger keys x 2, volume up and down keys, power key, side Fn keys x 2 | |
| Hard keys | - | - | - |
| Touch panel | Electrostatic capacitance method (reinforced glass specifications) | Electrostatic capacitance method (reinforced glass specifications) | Electrostatic capacitance method (reinforced glass specifications) |
| Scanner | High-intensity white LED | High-intensity white LED | High-intensity white LED |
| Reading light source | Visible light semiconductor laser (655 nm) | Visible light semiconductor laser (655 nm) | Visible light semiconductor laser (655 nm) |
| Pointer light source | Output 390 μW | Output 390 μW | Output 390 μW |
| Minimum resolution | Class 1 laser product (IEC 60825-1) | Class 1 laser product (IEC 60825-1) | Class 1 laser product (IEC 60825-1) |
| Field range | 2D code: 0.169 mm, barcode: 0.076 mm | 2D code: 0.169 mm, barcode: 0.076 mm | 2D code: 0.169 mm, barcode: 0.076 mm |
| Supported codes | UPC/EAN/JAN (add-on code supported), CODE128, GS1-128, CODE39, Codabar (NW-7), CODE93, ITF, COOP2of5, industrial 2of5, QR code, micro QR, DataMatrix (ECC200), PDF417, GS1 DataBar, composite symbol, Postal | UPC/EAN/JAN (add-on code supported), CODE128, GS1-128, CODE39, Codabar (NW-7), CODE93, ITF, COOP2of5, industrial 2of5, QR code, micro QR, DataMatrix (ECC200), PDF417, GS1 DataBar, composite symbol, Postal | UPC/EAN/JAN (add-on code supported), CODE128, GS1-128, CODE39, Codabar (NW-7), CODE93, ITF, COOP2of5, industrial 2of5, QR code, micro QR, DataMatrix (ECC200), PDF417, GS1 DataBar, composite symbol, Postal |
| Wireless LAN | IEEE802.11 a/b/g/n/ac 2.4 GHz (b,g,n: 1 to 11 ch) 5.2 GHz, 5.3 GHz (a/n/ac)*1 | IEEE802.11 a/b/g/n/ac 2.4 GHz (b,g,n: 1 to 14 ch) 5.2 GHz, 5.3 GHz, 5.6 GHz, 5.8 GHz (a/n/ac)*1*2 | IEEE802.11 a/b/g/n/ac 2.4 GHz (b,g,n: 1 to 11 ch) 5.2 GHz, 5.3 GHz (a/n/ac)*1 |
| Communication | Bluetooth® V5.1 BR/EDR/LE | Bluetooth® V4.2 BR/EDR/LE | Bluetooth® V5.1 BR/EDR/LE |
| WWAN | 4G LTE/3G, SIM-free, 1 nano SIM slot | 4G LTE/3G, SIM-free, 1 nano SIM slot | - |
| GNSS | GPS, A-GPS, GLONASS, Beidou | GPS, A-GPS, GLONASS, Beidou | - |
| NFC | ISO14443 Type A, B, FeliCa, ISO15693 | ISO14443 Type A, B, FeliCa, ISO15693 | ISO14443 Type A, B, FeliCa, ISO15693 |
| External media | micro SD/SDHC/SDXC UHS-I | micro SD/SDHC/SDXC UHS-I | micro SD/SDHC/SDXC UHS-I |
| Power supply | Dedicated lithium ion battery pack | Dedicated lithium ion battery pack | Dedicated lithium ion battery pack |
| Main battery | Built-in lithium ion secondary battery, time: approx. 1 month*3 | Built-in lithium ion secondary battery, time: approx. 1 month*3 | Built-in lithium ion secondary battery, time: approx. 1 month*3 |
| Clock | - | - | - |
Specifications (Expansion Units)
| Model | DX-BS8 | DX-BS3 | DX-BQ6 | DX-BQ3 |
|---|---|---|---|---|
| Dimensions (W x H x D) | 65.5 x 170.5 x 30.0 mm | 65.5 x 170.5 x 30.0 mm | 65.5 x 161.0 x 30.0 mm | 65.5 x 161.0 x 30.0 mm |
| Weight | Approx. 130 g | Approx. 130 g | Approx. 120 g | Approx. 120 g |
| Operating temperature | -20 to +50 °C | -20 to +50 °C | -20 to +50 °C | -20 to +50 °C |
| Storage temperature | -30 to +70 °C | -30 to +70 °C | -30 to +70 °C | -30 to +70 °C |
| Operating humidity | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) |
| Storage humidity | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) | 10 to 80 %RH (no condensation) |
| IP rating | IP65/IP67 | IP65/IP67 | IP65/IP67 | IP65/IP67 |
| Drop resistance | 2.0 m (onto concrete) | 2.0 m (onto concrete) | 2.0 m (onto concrete) | 2.0 m (onto concrete) |
| Power supply | Dedicated lithium ion battery pack | Dedicated lithium ion battery pack | Dedicated lithium ion battery pack | Dedicated lithium ion battery pack |
| Main battery | Built-in lithium ion secondary battery, time: approx. 1 month*3 | Built-in lithium ion secondary battery, time: approx. 1 month*3 | Built-in lithium ion secondary battery, time: approx. 1 month*3 | Built-in lithium ion secondary battery, time: approx. 1 month*3 |
| Clock | - | - | - | - |
WARRANTIES AND DISCLAIMERS
KEYENCE warrants that the product will be free from defects in materials and workmanship for a period of one (1) year from the date of purchase. KEYENCE shall, at its option, repair or replace any defective product returned to it within the warranty period. This warranty shall not apply to any product that has been misused, abused, altered, or damaged by accident or negligence. KEYENCE shall not be liable for any indirect, incidental, or consequential damages arising from the use of the product. The foregoing warranty is exclusive and in lieu of all other warranties, express or implied, including but not limited to, any implied warranty of merchantability or fitness for a particular purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
TRANSFER OF OBLIGATIONS:
KEYENCE CORPORATION's obligations and liabilities are limited to the terms and conditions set forth in this warranty. Any unauthorized modifications or repairs will void this warranty. KEYENCE is not responsible for any costs incurred in removing or reinstalling the product. This warranty is non-transferable and applies only to the original purchaser of the product.
KEYENCE CORPORATION
Head Office: 1539-1, Kitakoji, Hiyoshi-cho, Takatsuki, Osaka 569-1193, Japan
Phone: +81-72-684-2525
URL: www.keyence.com
Americas: KEYENCE CORPORATION OF AMERICA
Phone: +1-201-930-0333
URL: www.keyence.com/am
Europe: KEYENCE DEUTSCHLAND GmbH
Phone: +49-6103-7340-0
URL: www.keyence.de
Asia: KEYENCE (SHANGHAI) CO., LTD.
Phone: +86-21-5017-1500
URL: www.keyence.com.cn
Korea: KEYENCE CORPORATION OF KOREA
Phone: +82-2-545-2255
URL: www.keyence.co.kr
Taiwan: KEYENCE TAIWAN CO., LTD.
Phone: +886-2-2715-7000
URL: www.keyence.com.tw
Hong Kong: KEYENCE HONG KONG LIMITED
Phone: +852-2261-2121
URL: www.keyence.com.hk
Singapore: KEYENCE SINGAPORE PTE LTD
Phone: +65-6221-1355
URL: www.keyence.com.sg
Malaysia: KEYENCE MALAYSIA SDN. BHD.
Phone: +60-3-7959-1111
URL: www.keyence.com.my
Thailand: KEYENCE (THAILAND) CO., LTD.
Phone: +66-2-362-2177
URL: www.keyence.co.th
Indonesia: PT. KEYENCE INDONESIA
Phone: +62-21-572-3000
URL: www.keyence.co.id
India: KEYENCE INDIA PVT. LTD.
Phone: +91-11-4651-4000
URL: www.keyence.co.in
KEYENCE INDIA PVT. LTD. operates multiple offices across India, including locations such as Delhi, Mumbai, Bangalore, Chennai, Pune, Hyderabad, Ahmedabad, Kolkata, Jaipur, Chandigarh, Lucknow, Surat, Indore, Coimbatore, Visakhapatnam, Bhopal, Kochi, Nagpur, Patna, Vadodara, Kanpur, Ranchi, Rajkot, Nashik, Agra, Aurangabad, Bhubaneswar, Dehradun, Guwahati, Kozhikode, Mysore, Raipur, Shimla, Trivandrum, Varanasi, Vijayawada, Warangal, and Zirakpur.
Vietnam: KEYENCE VIETNAM CO., LTD.
Phone: +84-28-3519-0000
URL: www.keyence.com.vn
Australia: KEYENCE AUSTRALIA PTY. LTD.
Phone: +61-2-9431-7700
URL: www.keyence.com.au
New Zealand: KEYENCE NEW ZEALAND LTD.
Phone: +64-9-309-1300
URL: www.keyence.co.nz
United Kingdom: KEYENCE (U.K.) LIMITED
Phone: +44-1923-230200
URL: www.keyence.co.uk
France: KEYENCE FRANCE S.A.S.
Phone: +33-1-3420-7070
URL: www.keyence.fr
Italy: KEYENCE ITALIA S.P.A.
Phone: +39-02-3214-1414
URL: www.keyence.it
Spain: KEYENCE ESPAÑA S.A.U.
Phone: +34-91-444-5000
URL: www.keyence.es
Netherlands: KEYENCE NEDERLAND B.V.
Phone: +31-76-543-0000
URL: www.keyence.nl
Belgium: KEYENCE BELGIUM B.V.B.A.
Phone: +32-2-720-7000
URL: www.keyence.be
Switzerland: KEYENCE (SCHWEIZ) AG
Phone: +41-44-835-4000
URL: www.keyence.ch
Sweden: KEYENCE NORDIC AB
Phone: +46-8-519-000-00
URL: www.keyence.se
Finland: KEYENCE NORDIC AB
Phone: +358-9-615-000-00
URL: www.keyence.fi
Norway: KEYENCE NORDIC AB
Phone: +47-22-87-00-00
URL: www.keyence.no
Denmark: KEYENCE NORDIC AB
Phone: +45-36-90-00-00
URL: www.keyence.dk
Austria: KEYENCE AUSTRIA GmbH
Phone: +43-1-877-8770
URL: www.keyence.at
Poland: KEYENCE POLSKA SP. Z O.O.
Phone: +48-22-518-0000
URL: www.keyence.pl
Czech Republic: KEYENCE CZECH S.R.O.
Phone: +420-2-3300-4000
URL: www.keyence.cz
Hungary: KEYENCE HUNGARY KFT.
Phone: +36-1-231-1100
URL: www.keyence.hu
Portugal: KEYENCE PORTUGAL LDA.
Phone: +351-21-417-3333
URL: www.keyence.pt
Ireland: KEYENCE (U.K.) LIMITED
Phone: +353-1-401-9800
URL: www.keyence.ie
Brazil: KEYENCE DO BRASIL LTDA.
Phone: +55-11-3045-0000
URL: www.keyence.com.br
Mexico: KEYENCE MEXICO, S.A. DE C.V.
Phone: +52-55-5093-5500
URL: www.keyence.com.mx
Canada: KEYENCE CANADA INC.
Phone: +1-905-238-1111
URL: www.keyence.ca
Chile: KEYENCE CHILE LTDA.
Phone: +56-2-2378-4000
URL: www.keyence.cl
Colombia: KEYENCE COLOMBIA S.A.S.
Phone: +57-1-635-0000
URL: www.keyence.com.co
Peru: KEYENCE PERU S.A.C.
Phone: +51-1-500-0000
URL: www.keyence.com.pe
Philippines: KEYENCE PHILIPPINES INC.
Phone: +63-2-8816-0000
URL: www.keyence.com.ph
South Africa: KEYENCE SOUTH AFRICA (PTY) LTD.
Phone: +27-11-657-7500
URL: www.keyence.co.za
Turkey: KEYENCE TURKEY LTD. ŞTİ.
Phone: +90-216-528-6000
URL: www.keyence.com.tr
United Arab Emirates: KEYENCE MIDDLE EAST FZE
Phone: +971-4-391-1100
URL: www.keyence.ae
Russia: KEYENCE RUS OOO
Phone: +7-495-775-0000
URL: www.keyence.ru
Israel: KEYENCE ISRAEL LTD.
Phone: +972-3-744-0000
URL: www.keyence.co.il
Outline Dimensional Drawings
Diagram description: Visual representations of the dimensions for the DX-A600/A600GE, DX-A400/A400GE, and DX-W600 models, showing their width, height, and depth.
