Battery Camera QUICK GUIDE

What's in the box

Please consult this checklist for all parts.

• Battery Camera
• Power adapter
• USB cable
• Screws (2 kinds)
• Pin
• Bracket
• Silicone plug
• User Manual

Device Components

Front View: The device features a Status Light, Camera lens, PIR sensor, Microphone, Speaker, Power button, and Micro USB port.

Bottom View: The bottom of the device has a Reset button and an SD card slot.

Install

Mode 1: Bottom Bracket Installation

Description of diagram: A camera is shown being attached to a wall-mounted bracket. The steps are: 1. Fix the bracket to the wall with the mounting screws. 2. Install the camera in the bracket and lock it with the screw.

Mode 2: Side Bracket Installation

Description of diagram: A camera is shown being attached to a wall-mounted angled bracket. The steps are: 1. Fix the mounting bracket in the angle wall mount. 2. Fix the angle wall mount to the wall. 3. Install the camera in the bracket and lock it with the screw.

Connect

Download

The Cloudedge app is available for both iOS and Android OS. Search for 'Cloudedge' in the App Store or Android Market, or scan the QR-Code to download the App.

Support: Available for iPad, iOS, and Android devices.

Add device

Log in to CloudEdge, select "Add Device", and add the smart camera to the App according to the on-screen tips. Ensure the smart camera is close to the router when configuring.

Note: If you need to re-select the WiFi network, press and hold the "RESET" button for 5 seconds. The device will restart, and the indicator will be flashing red.

FAQ

Q: The device cannot be previewed properly?

A: Check if the network is normal. You can place the camera closer to the router. If the issue persists, it is recommended to reset the device and add it again.

Q: Why is it still in the list of devices after resetting?

A: Resetting the device only resets the network configuration. It does not change the configuration on the App. You need to remove and delete the camera from the App.

Q: How to connect the camera to another router?

A: First, remove and reset the device in the App, then configure the device again using the App.

Q: Why doesn't the device identify the SD card?

A: It is recommended to insert the SD card after powering off the device. Confirm that the SD card is available and formatted as FAT32. The TF card may not be identified if the internet environment is poor.

Q: Why can't I get notifications on my cell phone App?

A: Please confirm that the App is running on your phone and that relevant reminder functions and mobile phone system notification/authority settings have been enabled.

Functions

Remote wake-up

The camera can enter a sleep mode to save power. You can wake it up for a preview in the App.

Full-duplex audio

You can see and hear visitors through the camera via your App.

PIR

When the camera detects motion, it sends an alarm message to your cell phone.

Low battery alarm

When the battery power drops below your set threshold, the App will send a notification to your mobile phone.

Record

Use an SD card or the Cloud-Storage Service to keep recording every moment.

Day & Night

Powerful night vision provides uninterrupted viewing, even in complete darkness.

Daytime View: An image shows a well-lit interior scene.

Night View: The same scene is shown in monochrome, indicating night vision capabilities.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.