Neewer RT108 Wireless Electric Camera Slider User Manual

Package Contents

The package includes:

• Electric Camera Slider
• NP-F550 Battery
• USB Charger
• Allen Wrench/Screw
• Ball Head
• Remote Control
• Shutter Cable (C1, C3, N1, N3, S1, S2)

Slider Overview

The slider has three operational modes:

• Pan Mode: The adjustable bar remains level as set by the scale marking.
• Focus Mode: The left adjustable bar is set higher than the right adjustable bar.
• Sweep Mode: The right adjustable bar is set higher than the left adjustable bar.

Assembling the Slider

The slider is pre-assembled before delivery. The assembly steps involve:

1. Sliding the belt clamp into the left slot of the slider and securing it with side screws.
2. Routing the belt through the bearing wheel and pulley as shown.
3. Securely attaching the motor to the slider.
4. Sliding the belt clamp into the right slot of the slider and tightening the screw.

Product Illustration & Remote Control Introduction

The remote control features an operation joystick, a display screen, a Type-C power port, a shutter jack, an NP-F series battery holder, and a power switch.

Pairing a Device with the Slider

The product is pre-configured for pairing. To pair:

1. Press and hold the joystick on the remote control.
2. Turn on the remote control.
3. Turn on the motor.
4. The indicator light will flash red and green alternately.
5. Pairing is successful after approximately 3 seconds.

Power Sources

Power can be supplied using Sony NP-type batteries or a compatible alternative. Alternatively, a 5V/2A power bank or adapter can be used via the Type-C port.

Using the Joystick

The joystick controls movement:

• Left/Right: Move the joystick left or right for left/right movement. Center to release.
• Up/Down: Move the joystick up or down for up/down movement. Center to release.
• Confirm: Press the joystick to confirm.
• Exit: Press and hold the joystick for 2 seconds to exit.

A/B Point Setting

After powering on, the slider automatically searches for points A and B. You can manually set point A by moving the joystick vertically and point B by moving it left and right, then pressing the joystick to confirm.

To set points A and B:

1. Move the joystick left and right to set point A. Press the joystick to confirm.
2. Move the joystick left and right to set point B. Press the joystick to confirm. The device will then enter the main interface.

Reset A/B Point

The interface allows for resetting A/B points.

Video Mode

In Video Mode, you can configure:

• Ramp: Controls acceleration and deceleration at start/stop. Options: Yes (Y), No (N), Off.
• Loop: Enables continuous cycling. Options: Yes (Y), No (N), Off.
• Manual: Move the joystick fully left or right to start the slider; it stops when released.
• Start Point: Select to begin from point A or point B.
• Start: Initiate or pause the movement.
• Duration: Total time for the movement (automatically calculated).

Time-lapse Photography Mode

In Time-lapse Mode, configure:

• Interval: Time between each photo.
• Exposure: Camera shutter exposure time.
• Frames: Total number of photos to be taken.
• Motinless: Completes shooting at the original position.
• Start Point: Choose to start from point A or point B.
• Start: Start or pause the sequence.
• Duration: Total time for the time-lapse (automatically calculated).

Settings:

• Language: Supports English and Chinese.
• Factory Init: Resets all settings to factory defaults.
• Delay: Time delay before shooting begins.

Note: H = hours, M = minutes, S = seconds. The default minimum interval time is longer than the exposure time by 2 seconds.

Product Specifications

Operating Environment:

• Operating Temperature: -10~50°C
• Storage Temperature: -10~50°C

Slider Rail Specifications:

• Maximum Load Capacity: 5KG (horizontal), 2.5KG (at 45°)
• Product Material: Carbon Fiber + Aluminum Alloy
• Communication Interface: 2.4G

Electronic Specifications:

• Input Voltage: 5V~7.4V DC
• Maximum Current: 1A
• Typical Current: 800mA

Hardware Interface:

• Shutter Interface: 1x JACK 2.5MM
• Power Interface: 1x Type-C, Sony NP-F series batteries

Safety Notes

1. Use an adapter or charger with a DC 5V/2A~7.4V/2A output.
2. Do not expose the product to direct sunlight for extended periods.
3. Do not place the product near or inside a heat source.
4. Do not disassemble the product to prevent personal injury or damage.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

UK REP: Lingfeng Electronic (UK) Ltd, International House, 10 Churchill Way, Cardiff, CF10 2HE, United Kingdom

EC REP: NW Formations GmbH (for authorities only), Hoferstrasse 9B, 71636 Ludwigsburg, Germany