KULINARISK

Safety Information

For your own safety and correct operation of the appliance, please read this manual carefully before installation and operation. Always keep these instructions together with the appliance, even if it is sold or transferred to third parties. It is important that users are familiar with all the appliance's operating and safety characteristics.

Connection of the wiring must be performed by a specialist technician.

The manufacturer cannot be held responsible for any damage resulting from incorrect or inadequate installation.

The minimum safety distance between the cooker hob and the extractor hood is: for electrical hob 600mm and for gas hob 650mm.

If the gas hob installation instructions specify a distance greater than that indicated above, this must be taken into account.

Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.

The cut-out devices must be installed in the fixed system according to the wiring system regulations.

For Class I appliances, check that the domestic power supply has a suitable earthing connection.

Connect the hood to the flue with a pipe with a minimum diameter of 120 mm. The fume path must be as short as possible.

All the regulations regarding air discharge must be complied with.

Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of ventilation must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 4 Pa mbar to prevent fumes being drawn back into the room by the cooker hood.

The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

The power cord, if damaged, must be replaced by the manufacturer or by a service technician.

Connect the plug to a socket complying with current regulations, located in an accessible place.

Regarding the technical and safety measures to be adopted for fume discharging it is important to strictly follow the regulations provided by the local authorities.

⚠️ WARNING:

Before installing the hood, remove the protective films.

Use only screws and small parts of a type suitable for the hood.

⚠️ WARNING:

Failure to install the screws or fixing devices in accordance with these instructions may result in electrical hazards.

Connect the hood to the power supply by means of a bipolar switch with a distance between the contacts of at least 3 mm.

Do not look directly at the light through optical devices (binoculars, magnifying glasses...).

Do not flambé under the hood; risk of fire.

This appliance can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or lacking in experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Children must not play with the appliance. Cleaning and maintenance by the user must not be performed by children, unless they are supervised.

Children should be supervised to ensure that they do not play with the appliance.

The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lacking in experience and knowledge, unless they have been given supervision or instruction.

The accessible parts may become hot when used with cooking appliances.

Clean and/or replace the filters after the time specified (fire hazard).

There must be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

Kitchen hoods and other cooking fume extractors can affect the safe operation of appliances which burn gas or other fuels (including those in other rooms) due to the backflow of combustion gases. These gases can cause carbon monoxide poisoning. After installing a kitchen extractor hood or any other cooking fume extractor, make sure that the gas appliances are tested by a certified technician to guarantee that there is no backflow of combustion gases.

General Information

Use

Installation Method

The hood has been designed for installation and use in the "suction version" or in the "air recirculation version".

Extraction version (see symbol in the installation instructions)

Cooking steam is suctioned and channelled outside the house through a discharge duct (not supplied), fitted to the hood steam outlet. Make sure that the outlet duct is properly installed at the air outlet, using a suitable connection system.

Air recirculation version (see symbol in the installation instructions)

The air is filtered through one or more carbon filters, and then resent into the room.

Important: Ensure appropriate air circulation around the hood.

Important: If the hood is supplied without carbon filters and installed on recirculation mode, these must be fitted before the hood can be used. The filters are commercially available.

The hood should be installed away from particularly dirty areas, windows, doors and heat sources. Wall mounting accessories are not included as they vary depending on the wall material. Use fixing systems suitable for the walls of your home and for the weight of the appliance. For further details, contact a specialist dealer. Keep this booklet for future consultation.

Filters Alarm

When the filter alarm is activated, the following messages will appear over time:

Grease filter must be cleaned: "A" key flashes once per second. For maintenance see paragraph Care and cleaning.

Anti-odour filter must be cleaned: "A" key flashes twice per second. For maintenance see paragraph Care and cleaning.

Once the filters have been regenerated reset the alarm signal (see paragraph Control Panel).

Product Description

The product is a wall-mounted extractor hood. The main components are labeled:

Control Panel

The control panel consists of buttons labeled A through E, each with specific functions:

BUTTONFUNCTION
A (Speed)Turns the motor on/off at speed one.
Attention: the product starts with the filter alarm disabled. Press and hold the button for approximately 2 seconds, with all loads deactivated (motor+lights), to activate the grease filter alarm. LED (B) flashes twice for confirmation. To turn off the alarm, press the button again and hold it for at least 2 seconds. LED (B) flashes once.
B (Speed)Turns the motor on at speed two / Activates the carbon filter alarm.
Attention: the product starts with the filter alarm disabled. Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to turn the activated carbon filter alarm on. LED (A) flashes twice to confirm. To turn off the alarm, press the button again and hold it down for at least 2 seconds. LED (A) flashes once. Only for the recirculation mode.
C (Speed)Runs the motor at speed three / Resets the grease filter and carbon filter saturation alarm.
Press and hold the button for approximately 2 seconds, with all loads deactivated (motor+lights), to reset the filter saturation alarm. LED (A) flashes three times.
D (Speed)Turns the motor on at Booster speed. This speed is timed for 6 minutes. At the end of this time, the system returns automatically to the speed that was set before. If it is activated with the motor turned off, it will switch to OFF at the end of the time. To deactivate it, press button D or press button A.
E (Light)Press briefly: Turns the lighting system on and off at maximum intensity. Press and hold to change the lighting intensity up or down.

General Tips

Cleaning and Maintenance

Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.

IMPORTANT: Clean the hood using a damp cloth and a neutral liquid detergent.

Long-life Carbon Filter

The odour filter can be washed and regenerated every 3-4 months (or more frequently if the hood is subject to intensive use), up to a maximum of 8 regeneration cycles (in case of particularly intensive use it is recommended that you do not exceed 5 cycles).

Regeneration procedure

Grease Filters

Continue to clean or replace the filters at the scheduled intervals to keep the hood in good working order and avoid the potential risk of fire due to the excessive build-up of grease. The grease filters must be cleaned after every 2 months of operation or more frequently in the case of very intense use and are dishwasher safe.

Light Replacement

For replacement, contact an Authorised Service Centre.

What to do if...

If there is a fault, first try to find a solution yourself. If you are unable to resolve the problem yourself, contact an authorised service centre.

? In the event of improper use of the appliance or installation carried out without respecting the assembly instructions, it may be necessary to pay for the visit of an Authorised Service Centre technician, even during the warranty period.

PROBLEMPOSSIBLE CAUSESOLUTION
Appliance not stable.The appliance is not correctly installed.Follow the Installation instruction enclosed to the appliance.
Appliance is not in horizontal position.The appliance is not correctly installed.Follow the Installation instruction enclosed to the appliance.
Performance in terms of oil capture are not satisfying.Oil and grease on metal filters or charcoal filters.Follow the cleaning frequency of filters as described in the user manual.
Appliance does not work.The appliance is not correctly connected.Verify that the main cable is connected to the motor group or the plug is connected to the socket.
The light does not work.The LED is broken.For replacement, contact the Authorized Service Centre.
Noise of hood is higher than customer expectation.Air outlet diameter in the wall is too small, causing a pressure drop and an increase in motor speed.Follow the Installation instruction enclosed to the appliance.
Product is installed in recirculation mode.Product in recirculation mode (and using a charcoal filter) will generate a higher noise than a product in extraction mode.
More than one bend in the ventilation duct.If the exhaust system in the building has multiple bends or a long distance, this can increase the noise of the product.
Button A light flashing once per second.Grease filter alarm.Please clean grease filter and reset alarm. Refer to care and cleaning guide for maintenance. Press and hold the "C" button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the grease filter saturation alarm. LED (A) flashes three times to confirm.
Button A lights flashing twice per second.Charcoal filter alarm.Charcoal filter alarm. Please clean charcoal filter and reset alarm. Refer to care and cleaning guide for maintenance. Press and hold the "C" button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the charcoal filter alarm. LED (A) flashes three times to confirm.

Before contacting the Authorised Service Centre:

Turn the power back on to check whether the problem has disappeared. If this is not the case, turn it off and repeat the operation after one hour. If the appliance still does not work correctly after carrying out the checks listed in the troubleshooting guide and turning the appliance back on, contact the Authorised Service Centre clearly explaining the problem and specifying:

Technical Data

FeatureUnitValue
Type of productWall mounted hood
DimensionsWidthmm 898
Depthmm 460
Min./max. output heightmm 730
Min./max. recirculation heightmm 1010
Airflow max* - Exhaustm³/h380
Noise max* - ExhaustdBA59
Airflow max* - Recirculatingm³/h340
Noise max* - RecirculatingdBA74
Total powerW276
Information on the lightTypeLED BAR
Number and power1 x 6W
ConnectionN/A
Minimum installation height - gas hobmm650
Minimum installation height - electric hobmm600
Net weightKg15

* Maximum speed (without booster setting)

[CE mark] This appliance has been designed, manufactured and sold in compliance with the EEC directives. The technical data are shown on the plate applied inside the appliance.

Environmental Aspects

Maintenance

The symbol ♻️ on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Packaging materials

The materials with the symbol ♻️ are recyclable. Dispose the packaging in suitable collection containers to recycle it.

IKEA Guarantee

How long is the IKEA guarantee valid?

This guarantee is valid for five years from the original date of purchase of your appliance at IKEA Pty Ltd, ABN 84 006 270 757, and IKEA NEW ZEALAND LIMITED, NZBN is 9429047515468.

The original sales receipt is required as proof of purchase. If service work is carried out under guarantee, this will not extend the guarantee period for the appliance.

Who will execute the service?

IKEA service provider will provide the service through its own service operations or authorized service partner network. Contact IKEA for further information.

If you encounter any trouble with the appliance and wish to register a service call or make a claim, please refer to www.ikea.com for your local store after sales customer service center phone number, online email and opening times.

Principal Address and Contact Details (Australia)

IKEA Pty Ltd

IKEA Service Office

L1 Clock Tower, 630 Princes Highway

Tempe, NSW 2044

Contact - IKEA Customer Service at www.IKEA.com

Principal Address and Contact Details (New Zealand)

IKEA New Zealand Limited

IKEA Service Office

L1 Clock Tower, 630 Princes Highway

Tempe, NSW 2044

Contact - IKEA Customer Service at www.IKEA.com

What does this guarantee cover?

The guarantee covers faults of the appliance, which have been caused by faulty construction or material faults from the date of purchase from IKEA. This guarantee applies to domestic use only. The products have been designed and tested for domestic purposes only and this guarantee does not cover damage arising from use of the Product in a commercial environment.

The exceptions are specified under the headline "What is not covered under this guarantee?".

Within the guarantee period, the costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible for repair without special expenditure. Replaced parts become the property of IKEA.

The guarantee exists only if the appliance complies and is installed in accordance with:

IKEA's guarantee is subject to Australian Consumer Law - see Schedule 2 to Competition and Consumer Act, 2010 and New Zealand Consumer Guarantees Act 1993. This guarantee is in addition to (and does not exclude, restrict or modify in any way) any non-excludable statutory warranties in Australia.

What will IKEA do to correct the problem?

IKEA appointed service provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee.

They will notify you as to whether your claim is covered under this guarantee. If your claim is approved, the IKEA service provider or its authorized service partner, will then, at its sole discretion, either repair the defective product or replace it with the same or a comparable product.

What is not covered under this guarantee?

How country law applies

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law (ACL) and New Zealand Consumer Guarantees Act 1993. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This guarantee is not intended in any way to limit or exclude such rights and remedies that you may have under law.

You can find out more information in the following web pages:

Area of validity

This IKEA guarantee applies only to products purchased and installed in AUSTRALIA and New Zealand.

What you must do to make a claim under the guarantee:

To make a claim under the guarantee contact IKEA after sales customer service center at the above address or www.ikea.com for your local store customer service phone number, online email and opening times. Please describe the problem that you are facing with the appliance in detail along with your product article number (8 digit code) and date of purchase at the time of call registration.

Please do not hesitate to contact the dedicated after sales customer service center for IKEA appliances to:

  1. Make a service request under this guarantee;
  2. Ask for clarification on installation of the IKEA appliance in the dedicated IKEA kitchen furniture.
  3. Ask for clarification on user manual contents and specifications of the IKEA appliance.

To ensure that we provide you with the best assistance, please read carefully the Assembly Instructions and/or the User Manual section of this booklet before contacting us.

How to reach us if you need our service

The IKEA after sales customer service centre will assist you on the phone with basic trouble shooting for your appliance at the time of service call request. Please refer to www.ikea.com and select your local store for local store phone numbers and opening times.

? Please describe the problem that you are facing with the appliance in detail along with your product article number (8 digit code) and date of purchase at the time of call registration.

SAVE THE SALES RECEIPT! Kindly keep all these details and original invoice of purchase handy during the service technician's visit to enable him to carry out the job. It is your proof of purchase and required for the guarantee to apply. Note that the receipt reports also the IKEA article name and number (8 digit code) for each of the appliances you have purchased.

Country name in local languagesTelephone numberOpening times
Australia(02) 90100264
New Zealandwww.ikea.com

PDF preview unavailable. Download the PDF instead.

kulinarisk-wall-mounted-extractor-hood-stainless-steel-glass AA-2027178-10-1 SCHEMA ST4 ST4 PDF Engine (Build 12.0.4.0)

Related Documents

Preview KULINARISK Extractor Hood User Manual & Installation Guide | IKEA
Detailed user manual and installation guide for the IKEA KULINARISK extractor hood. Learn about safety, installation, operation, cleaning, and warranty information.
Preview BALANSERAD Wall Mounted Extractor Hood User Manual | IKEA
Comprehensive user manual for the IKEA BALANSERAD wall-mounted extractor hood. Find detailed information on safety, installation, operation, cleaning, maintenance, troubleshooting, technical specifications, and the IKEA guarantee.
Preview IKEA VIGGBO Wall-Mounted Extractor Hood User Manual and Installation Guide
Comprehensive user manual and installation guide for the IKEA VIGGBO wall-mounted extractor hood, covering safety information, installation steps, product features, cleaning and maintenance, troubleshooting, technical specifications, environmental considerations, and IKEA warranty details.
Preview KULINARISK Range Hood User Manual - IKEA
Comprehensive user manual for the IKEA KULINARISK range hood, detailing installation, safe operation, maintenance, troubleshooting, and technical specifications. Essential guide for optimal kitchen air quality.
Preview RYTMISK Wall Mounted Cooker Hood User Manual - IKEA
Comprehensive user manual for the IKEA RYTMISK wall-mounted cooker hood. Contains essential information on safety, installation, operation, maintenance, troubleshooting, technical specifications, and IKEA's guarantee.
Preview IKEA STACKBO Kitchen Hood: Product Overview and Technical Specifications
Detailed information about the IKEA STACKBO kitchen hood, including product description, control panel functions, energy efficiency data, and technical specifications. Covers airflow, sound levels, lighting, and power consumption.
Preview IKEA STACKBO Extractor Hood: Installation, Safety, and User Manual
Comprehensive guide for the IKEA STACKBO kitchen extractor hood, covering installation, safety precautions, operation, cleaning, maintenance, and warranty information. Essential reading for safe and effective use.
Preview IKEA BEJUBLAD Extractor Hood User Manual and Specifications
Comprehensive guide for the IKEA BEJUBLAD extractor hood, detailing product features, control functions, energy efficiency ratings, and support contact information.