BODEGA R50 RV Refrigerator User Manual

1. Safety Instructions

⚠️ WARNING!

• Do not operate the appliance if it is visibly damaged.
• Do not block the gaps of the fridge with things like pin, wire, etc.
• Do not expose the appliance to rain or soak it in water.
• Do not place the appliance near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.).
• Do not store any explosive substances like spray cans with a flammable propellant.
• Ensure the supply cord is dry and not trapped or damaged. Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.
• Check the voltage specification on the type plate corresponds to that of the energy supply. The appliance is only to be used with the power supply unit provided with the appliance.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Once unpacked and before turning on, the appliance must be placed on a level surface for more than 6 hours.
• Make sure that the appliance stays horizontally when it is running. The tilt angle must be less than 5° for long time running and be less than 45° for short time running.
• Keep the ventilation openings in the unit casing or in the built-in structure free of obstacles.
• Keep the appliance stable on the ground or in the car; Do not drain upside down.

❗ CAUTION!

• Repairs may only be carried out by qualified personnel. Incorrect repair may cause danger. The lamp and supply cord must be replaced by the manufacturer or qualified persons.
• The installation of DC power in the boat must be handled by qualified electricians.
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they've been given supervision or instruction concerning use of the device in a safe way and understand the hazards.

? NOTICE!

• Disconnect the power supply before each cleaning and maintenance and after every use.
• Do not use sharp tools to defrost; Do not damage the refrigerant circuit.
• Risk of child entrapment. Before you throw away your old refrigerator or freezer: take off the doors: leave the shelves in place so that children may not easily climb inside.
• Check if the cooling capacity of the appliance is suitable for storing the food or medicine. Food may only be stored in its original packaging or in suitable containers.
• If the appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.
• The appliance is intended to be used in household and similar applications such as: Staff kitchen areas in shops, offices and other working environments; Camping, Farm houses and by clients in hotels, motels and other residential environments; Bed and breakfast type environments; Catering and similar non-retail applications.
• Please according to local regulations regarding disposal of the appliance for its flammable refrigerant and blowing gas.

2. Product Features

• High-efficiency DC compressor and conversion module.
• CFC free and great heat insulation.
• Intelligent battery protection system prevents your vehicle from running out of battery.
• Dual temperature with single controller, LED display control panel for temperature setting.
• Easy to install, fridge/freezer compartments can be combined, reversible door.
• Detailed designs: removable door bins, crisper drawer, coating shelves, interior light, etc.

3. Product Structure

The refrigerator features the following components:

Diagram Description: A line drawing of the BODEGA R50 RV Refrigerator with the door open, illustrating the internal and external components. Key parts are labeled with numbers corresponding to the list above.

4. Installation

Step 1: Unpacking and Inspection

Ensure that the fridge is not damaged when opening the package after receiving the product. Any transportation damage could be reported to the place of purchase. Handle the product with the utmost care and attention.

Step 2: Cabinet Preparation

Prepare the cabinet. Leave space around the refrigerator to keep good ventilation (at least 50mm at the back and top, and 20mm at the sides). Always keep the fridge on a horizontal surface and away from heat sources.

Step 3: Power Connection

Connect the refrigerator to the vehicle 12V/24V DC system directly. Ensure the minimal cable cross-section is adequate based on the overall length of wire between the refrigerator and the battery. Connect the red cable to the positive terminal of the battery and the black cable to the negative terminal of the battery.

It is highly recommended that the installation is carried out by a qualified person. Ensure enough free wire is kept for moving the fridge into the cabinet.

Step 4: Placing the Fridge

Push the fridge into the cabinet carefully to avoid scratching the floor, and the power cable should be kept loose.

Step 5: Fixing the Refrigerator

There are three methods to fix the refrigerator:

Method 1: Mount to Cabinet Wall

Use the built-in screw holders (labeled ①, ②, ③, ④ in diagrams) on the side wall of the refrigerator. Drill holes through the screw holders into the side metal panel with screws (M5, 15mm minimal) and fix it on the wall. Use the screw cover to cover the hole. (Note: If the refrigerator needs to be drilled through, this should be confirmed before leaving the factory. Screws are not included.)

Diagram Description: Illustrates pre-installation dimensions (Inner Length: 420mm, Inner Height: 582mm, Inner Width: 529mm) and installation view showing screw holders, screws, and screw covers for mounting to a cabinet wall.

Method 2: Optional Standard Frame

Use an optional installation frame (standard frame) for a secure fit and a smart finish. This involves unscrewing the refrigerator's own fixings, placing the frame behind the door, fixing the frame to the refrigerator with screws, and then pushing the refrigerator into the cabinet. Finally, fix the refrigerator to the cabinet through the frame.

Diagram Description: Shows the process of attaching a standard frame to the refrigerator and then mounting it into a cabinet. Includes dimensions for the frame and cabinet space.

Method 3: Optional Flush-Mount Frame

Use an optional flush-mount frame for a seamless integration. The process is similar to the standard frame: unscrew refrigerator fixings, attach the frame flush with the door, fix the frame to the refrigerator with screws, push the refrigerator into the cabinet, and finally fix it through the frame.

Diagram Description: Illustrates the attachment of a flush-mount frame to the refrigerator and its subsequent installation into a cabinet. Includes dimensions.

Step 6: Final Verification

Once the installation is finished, check the continuity of the earth circuit and carry out all electrical safety testing provided for by current regulations. Protect and fix the cables to prevent accidental pulling, disconnection, contact with hot parts (above 50°C), or sharp parts.

5. Combining Fridge/Freezer Compartments

To combine the compartments, open the lid and pull out the divider horizontally.

Diagram Description: Shows the refrigerator with the lid open and the internal divider pulled out horizontally.

6. Reverse Door Open Direction

The door is reversible and can be opened from left to right or from right to left.

Diagram Description: Two illustrations showing the refrigerator door opening in opposite directions: one from right to left, and the other from left to right.

7. Function and Operation

The control panel allows for temperature management and operation settings.

Control Panel Layout: Features a display for temperature (e.g., "888-888"), buttons for temperature control ([Plus], [Minus]), mode selection ([Freezer], [Refrigerator]), settings ([SET]), and power ([ON/OFF]). A "Night light" indicator is also present.

• Power Supply: DC 12V/24V or AC 100-240V power (using dedicated adapter).
• Display Screen Initialization: Upon powering on, the buzzer sounds a long beep, and the display shows for two seconds before entering normal operation.
• Power ON/OFF: Press the [ON/OFF] button to switch the unit on or off.
• Night Mode: Under running state, long press the [Night light] button for 3 seconds to enter night mode. The screen turns off, and the night light illuminates in blue.
• Temperature Setting: Press the [Freezer]/[Refrigerator] button to select the compartment. When the corresponding screen flashes, use the [Plus] or [Minus] buttons to adjust the temperature. Settings are saved automatically after 4 seconds of inactivity. (Note: The displayed temperature is the current compartment temperature; it takes time to reach the set temperature.)
• Battery Protection Mode: Under running state, long press the [SET] button for 3 seconds until the left screen flashes. Press [Plus] or [Minus] to cycle through High, Medium, and Low settings (default is High). This mode prevents the vehicle battery from draining.
• Voltage Reference: The table below shows voltage cut-off and cut-in points for different battery protection modes (L, M, H) under DC 12V and DC 24V.

*The voltage is a theoretical value; actual values may vary. H mode is recommended for car power; M or L modes are for portable or backup batteries.

• Temperature Unit Setting: Switch off the fridge, long press the [SET] button for 3 seconds until "E1" is displayed. Press [SET] again to cycle through "E1" to "E5". Then press [Plus] or [Minus] to switch between Celsius (°C) and Fahrenheit (°F). (Default is °C).
• Reset: Switch off the fridge, long press the [SET] button for 3 seconds until "E1" is displayed. In "E1" mode, long press the [Plus] and [Minus] buttons simultaneously for 3 seconds to reset all settings.

Recommended Temperature for Common Food

The following table provides recommended temperature settings for various food types:

8. Care and Maintenance

Cleaning

• Unplug the device first to avoid electric shock.
• Use a damp cloth to clean the device and dry it.
• Remove the cover and drain from the hole at the bottom of the device.
• Do not soak the device in water and do not wash it directly.
• Do not use abrasive cleaning agents as these can damage the device.

Storage

If the device will not be in use for a long time, follow these steps:

• Turn off the power and remove the plug.
• Remove all items stored in the device.
• Remove the cover and drain from the hole, wipe off excess water with a soft rag.
• Put the device in a cool and dry place.
• Press the storage lock into the lock holder to keep the fridge door ajar, preventing the formation of unpleasant odours and mould when not in use.

Diagram Description: Shows the refrigerator with the storage lock engaged, keeping the door slightly open.

Defrosting

Humidity can form frost in the interior of the cooling device or on the evaporator, which will affect cooling performance. Defrost the device regularly to avoid this.

• Switch off the device.
• Take out the contents of the device.
• Remove the cover and drain from the hole.
• Keep the door open.
• Wipe off the defrosted water.

⚠️ Never use hard or sharp tools to remove ice or to loosen objects which have frozen in place.

9. App Connection

[QR Code for QZsmart App] Scan the QR Code with your smartphone or search for "QZsmart" in the App Store or Google Play to download the app.

Connection Requirements:

• Ensure your car fridge is on and your smartphone is connected to a 2.4 GHz Wi-Fi network. (Note: This device only works on 2.4 GHz Wi-Fi networks.)
• Ensure the Bluetooth function of your mobile phone is enabled.
• Download and install the QZsmart app. Authorize the app to access network and location services.
• If using the app for the first time, sign up; otherwise, log in.
• For a better Wi-Fi connection, it is recommended to reset the product's Wi-Fi before first use. This can be done by turning off the refrigerator and simultaneously long-pressing the "[Plus]" and "[Minus]" buttons on the control panel for 3 seconds until a beep is heard.

Add Device

Auto-connect (Recommended)

The app will automatically search for the device when Wi-Fi and Bluetooth are enabled. Follow these steps:

1. From the Home Page, press "Add Device" or the "[Plus]" icon (if a device is already added, this button may not appear).
2. When the device is found, press "Add". Ensure Bluetooth is enabled during this process.
3. Select your Wi-Fi network (ensure it is a 2.4G network).
4. Enter your router password.
5. Wait for the connection and click "NEXT".
6. Once added, you can change the device's name and location.
7. When finished, click "Done".

Manual connection

Select your model from the device menu:

1. Press "Add Device" or the "[Plus]" icon.
2. Select the corresponding product type and click the product diagram of the corresponding model.
3. After the product is shut down, press "Next".
4. Long press the "[Plus]" and "[Minus]" buttons on the control panel for 3 seconds until a beep is heard, then press "Next".
5. Select your Wi-Fi network (ensure it is a 2.4G network).
6. Enter your router password.
7. Click "Confirm". The next screen will prompt to connect your mobile phone to the device's hotspot.
8. Click "Go to connect". This will take you to your phone's settings (or Wi-Fi list for Android).
9. Select "SmartLife-XXXX" (your device's hotspot).
10. Navigate back to the QZsmart App.
11. Click "Next". Your smartphone will automatically connect.
12. Once the device is added, you can use the app menu to change the name and location of the device.
13. When you are finished, press "Done".

Follow the on-screen prompts in the app for detailed operation reminders.

NOTE: Connection may take up to 60 seconds. Once the device is added, you can use the app menu to change its name. Your mobile device must be connected to a 2.4GHz Wi-Fi network when pairing.

Using the App

The main app interface allows you to adjust freezer temperature, set the child lock, activate sleep mode, and control the fridge's power. When sleep mode is active, the compressor runs at a low speed to save power.

Clicking "More functions" allows you to change the temperature unit, adjust the temperature control bar in the freezer section, and set the battery protection mode.

App Interface Description: Two screenshots are provided. The first shows the main "Car refrigerator" interface with temperature settings for left and right compartments, battery protection status, and voltage. The second shows the "More features" screen with options for temperature scale (°C/°F), mode selection (Refrigerate/Freezer), and battery protection levels (H/M/L).

How to Unbind

A car refrigerator can only be connected to one mobile phone. To disconnect:

• First method: Turn off the refrigerator's switch and simultaneously long press the "[Plus]" and "[Minus]" buttons on the control panel for 3 seconds until a beep is heard.
• Second method: Open the app, go to the device page, click the "[Remove Device]" icon (usually a trash can or similar, depicted as a square with an arrow in the original document) in the upper right corner, and then click "Remove Device" at the bottom.

Cautions

• There may be a delay (about 1-3 minutes) in operating the machine via the mobile phone; please be patient.
• The app's language automatically switches with the mobile system's language.
• You can lock or unlock the control panel via the app's lock icon. The refrigerator's operation panel itself does not have a locking/unlocking function.
• This product includes Wi-Fi and Bluetooth. Bluetooth can be used in non-Wi-Fi environments. However, Bluetooth function requires initial successful connection via Wi-Fi. If Wi-Fi connection fails the first time, Bluetooth may not be usable in non-Wi-Fi environments.

10. Troubleshooting

Refer to the table below for common issues and their solutions:

11. Warranty

A limited warranty is provided for 1 year from the date of purchase for malfunctional devices, except under the following conditions:

• Contrived damage.
• Damage caused by force majeure such as earthquake, conflagration, etc.
• Damage from inappropriate use or violating this instruction.
• Damage or malfunction caused by disassembling.

12. Technical Information

*Due to product improvement, the technical information might be different from actual information; please refer to the rating label on the product.

Manufacturer: Foshan Alpicool Electric Appliance Co., LTD.

Address: 13A Xinlong Road Shiongliyue industrial Zone, Xintang Village, Lunjiao Town, Shunde District, Foshan City, Guangdong, China

Contact: Mickey | Tel: +1 (313) 913-7585 | E-Mail: info@bodegacooler.com

Warranty Activation and Support

Thank you for purchasing a BODEGA COOLER product. We hope you are satisfied with your purchase.

We offer a 12-month warranty for free. Once activated, your product is covered for any issues during this period, with replacement units/parts warranted.

What you need to do

For any help or questions during use, please contact BODEGA COOLER via their website at www.bodegacooler.com or send an email to info@bodegacooler.com. Support is typically provided within 24 hours.

When contacting support, please provide your Order ID, a detailed description of the problem, and a photo or video for clearer understanding and a better solution.