ZKTeco | Biometrics and Computer Vision
Installation Guide for ZKTECO models including: SpeedFace-V4L Pro Series, SpeedFace-V4L Pro Series Access Control Device, Access Control Device, Control Device, Device
ZKTeco Speedface-V4L Pro Access Control Device
File Info : application/pdf, 9 Pages, 1.33MB
DocumentDocumentInstallation Guide SpeedFace-V4L Pro Series Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual. Installation Environment Please refer to the following recommendations for installation: INSTALL INDOORS ONLY AVOID INSTALLATION NEAR GLASS WINDOWS AVOID DIRECT SUNLIGHT AND EXPOSURE AVOID USE OF ANY HEAT SOURCE NEAR THE DEVICE Y Avoid direct contact to sunlight for a long time. Y Protect the device from moisture, water, and rain. Y Handle the device with care. Y Ensure that the device is not installed near the sea or in other locations where metal oxidation and rust may develop if the device is exposed for an extended period. Y Protect the device from lightning. Y Ensure that the device only works in an acidic or alkaline environment briefly. How to Install the Device on the wall? Step 1: Stick the wall-mounting template to the wall and drill holes according to the wall-mounting template. 1 2 30mm 90° 6mm 1450mm -1- Step 2: Insert the expansion tubes into the mounting holes. Step 3: Attach the backplate on the wall using the wall mounting screws. Note: Please insert the wire through the backplate before installation. -2- Step 4: Attach the terminal to the backplate. Step 5: Attach the terminal to the backplate with a security screw. -3- Door Bell, Exit Button and Alarm Connection - -+ -+ Exit Button Bell Power Door Bell Alarm + WD1 WD0 GND GND BELLBELL+ SEN BUT AUX GND AL- GND +12V ID1 ID0 485A 485B GND NC COM NO AL+ + - Alarm's Power Switch Door Sensor and Smoke Detection Connection WD1 WD0 Door Sensor GND GND BELLBELL+ SEN BUT COM AUX NO GND Smoke Detector AL- GND +12V ID1 ID0 485A 485B GND NC COM NO AL+ -4- Power Connection GND 12V GND 12VDC Recommended Power Supply: Y 12V ± 10%, at least 3000mA. Y To share the power with other devices, use a power supply with higher current ratings. RS485 and Wiegand Connection WD1 WD0 GND GND BELLBELL+ SEN BUT AUX GND AL- GND +12V ID1 ID0 485A 485B GND NC COM NO AL+ Access Controller 485+ 485- RS485 GND Reader GND +12V WD1 WD0 Wiegand Reader -5- Ethernet Connection RX- RX+ 1 2 TX- 3 4 5 RJ 45 6 PC 7 TX+ 8 Default IP Address: 192.168.1.201 IP Address: 192.168.1.130 Subnet Mask: 255.255.255.0 Subnet Mask: 255.255.255.0 Click COMM. > Ethernet > IP Address on the device, input the IP address and click OK. Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally opened at power on) is connected with "NO1" and "COM" terminals, and the NC LOCK (normally closed at power on) is connected with"NC1"and"COM"terminals. Take NC Lock as an example below: Device not sharing power with the lock: Device sharing power with the lock: GND +12V ID1 ID0 485A 485B GND NC COM NO AL+ + - + DC12V - + FR107 - Normally Closed Lock GND +12V ID1 ID0 485A 485B GND NC COM NO AL+ - + FR107 + - Normally Closed Lock - - GND +12V GND +12V + + DC12V -6- DC12V Download Center Scan the QR Code to download the User Manual, Installation Guide and Quick Start Guide. QR Code (Download Center) -7- ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.