Audioxtra – Australian importer and distributor of Axis, Blaupunkt, Dynamat, HEMA Maps, Midland and Uniden
Instruction Manual for axis models including: APS401W, 12 24V Wireless 4 Sensor
3 (3) DESCRIPTION MIN SPEC MAX Power voltage (V DC) 10 35 Operating current (mA) 150 Operating temperature °C -20 80 Operating frequency (KHz) 39.3 40.7
Index of /wp-content/uploads/2021/04
File Info : application/pdf, 8 Pages, 1.43MB
DocumentDocument1 WIRING DIAGRAM Display Control Unit Antenna Reversing Light 12/24Vdc GND. 24V-12V Filter 12/24Vdc GND. Display The two outer sensors start detecting at Zone B. OFF HIGH Switch 1: OFF- Standard ON- Display distance less 20cm than actual. LOW Switch 2: Sensor sensitivity ON 2 TECHNICAL SPECIFICATION DESCRIPTION Power voltage (V DC) Operating current (mA) Operating temperature °C Operating frequency (KHz) Horizontal detection angle Vertical detection angle Distance detection accuracy (cm) Detection range (m) Buzzer sound volume (dB) DETECTION ZONES DISPLAY ZONE A: 1.5 - 2.5m Number Only ZONE B: 1 - 1.5m Green ZONE C: 0.5 - 1m Amber ZONE D: 0 - 0.5m Red MIN SPEC MAX 10 35 150 -20 80 39.3 40.7 120° 60° 10 0.05 2.5 75 105 SOUND ZONE A: 1.5 - 2.5m None ZONE B: 1.2 - 1.5m 2 beeps per second ZONE C: 0.9 - 1.2m 3 beeps per second ZONE D: 0.6 - 0.9m 4 beeps per second ZONE E: 0.3 - 0.6m 5 beeps per second ZONE F: 0 - 0.3m Constant tone 3 SENSOR 18.8mm Rubber Angled Sensor Front BACK Side 16mm 26mm 18.8mm UNDER MOUNTS 24.5mm Under Mount Brackets and Spacers 65mm 19mm DISPLAY 99 x 20H x 28Dmm 4 FEATURES 1. Wireless range up to 30m. 2. Towbar / Spare Wheel detection zone. 3. Suitable for flush mounting into metal bumpers and under body/tray mounting. 4. System Self-Checking Function - On start-up the system will beep twice; If there is any faulty sensor, the system will beep once. 5. IP69K Control Box & IP68 Sensors and Connectors. 6. E-Mark certified. TROUBLE-SHOOTING GUIDE PROBLEM CAUSE The system fails to start when the reverse gear Wrong connection of power lead is engaged Wrong jack connection The system always detects the same distance The system fails to detect the obstacles False alarm Sensor detects the ground Wrong sensors connection Sensor detects the ground SOLUTION Check the power lead Check the connectors Check and adjust the vertical sensor angle Check and reset the system Check and adjust the vertical sensor angle 5 SPECIAL NOTES EX.1 EX.2 EX.3 EX.4 EX.5 6 When the car approaches a smooth slope, the slope may not be detected. The sensors may not detect a small or smooth round pole. Point A will be detected prior to point B, as it comes closer. However, point A may fall into the sensors' blind zone, and point B cloud be misjudged as the closest point. The sensors may not detect any sponge-like material obstacle as the ultrasonic wave was absorbed. Complex situation: point A may not be detected. 7 WARRANTY Congratulations on your purchase of a quality Mobile Safety System! You're joining thousands of satisfied customers who enjoy & experience the benefits of the products we distribute. In the unlikely event that some technical difficulty arises with your purchase, be assured that we are most anxious to see that the problem is quickly rectified to your satisfaction. Please familiarise yourself with the following simple conditions of our warranty. This warranty covers faults through component failure or failure of the product to operate in accordance with published specifications. Product failure as a result of unreasonable environmental conditions, accident, misuse, improper installation, unauthorised repair, vehicle electrical or wiring faults or neglect etc, will not be covered by this warranty. Removal and installation costs, if any, would be paid by the owner as well as any freight or postage costs of transporting the product to AudioXtra. AudioXtra shall not be liable or responsible for any loss of use of this product or any form of consequential loss. CONSUMER WARRANTY This product is warranted by AudioXtra Pty Ltd to be free from defects in materials and workmanship under NORMAL USE for a period of TWENTY FOUR MONTHS from the date of purchase. WITHIN 30 DAYS OF PURCHASE DATE: Please return the unit for replacement to our National Service Centre or the Retailer from where you made the purchase. All accessories must be included. Proof of purchase date must accompany the products. AFTER 30 DAYS OF PURCHASE DATE: Warranty repair and service is carried out by our National Service Centre. Repair and service will be carried out at no cost to the owner if proof of ownership and the date of purchase can be verified to the satisfaction of the authorised centre concerned with this repair. This proof should take the form of either: a) The warranty card accompanying this product, stamped and dated by the dealer. b) A Tax Invoice or Receipt showing full details of original vendor, purchaser, model number and serial number. COMMERCIAL WARRANTY A product used in or associated with a commercial application will carry a limited SIX MONTH warranty. An abnormal commercial application is one where usage, dust, vibration, heat/cold and other environmental conditions exist at an extreme level. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please complete details below in the event of warranty service being required. Purchaser's Name: Purchaser's Address: Model Number: APS401W Serial Number: Dealer Name: Date of Purchase: / / Dealer Address: Invoice/Sales Docket no: General Hints: To expedite service and prompt return of the equipment, please: a) Clearly describe the fault in detail c) Include your return address b) Safely and securely pack the unit for transport d) Provide proof of purchase date as outlined above National Service Centre: 10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148 Australia Telephone: (02) 8841 9000 Fax: (02) 9636 1204 email: services@audioxtra.com.au PTY LTD audioxtra.com.au 8