TP-Link Omada Regulatory Compliance
Document for Ceiling Mount/Desktop EAP Series
FCC Compliance Information Statement
Product Name: Omada Ceiling Mount Access Point / Omada Desktop Access Point
Model Numbers: EAP610, EAP613, EAP650, EAP653, EAP670, EAP673, EAP720, EAP723, EAP770, EAP772, EAP783, EAP787, EAP603GP-Desktop, EAP610GP-Desktop, EAP650GP-Desktop, EAP650-Desktop
I.T.E. Power Supply Models:
- T120100-2B1 (For EAP610)
- T120150-2B1 (For EAP650 / EAP720)
- T120150-2B4 (For EAP603GP-Desktop / EAP650-Desktop)
- T120200-2B4 (For EAP670)
- T120250-2B4 (For EAP770)
- T535081-2B4 (For EAP610GP-Desktop / EAP650GP-Desktop)
Responsible Party: TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
Email: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with instructions, it may cause harmful interference to radio communications. No guarantee exists that interference will not occur in a particular installation. If interference occurs, users are encouraged to try to correct it by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications. Such modifications could void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
"To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 44cm (for EAP670 / EAP673 / EAP770 / EAP772) / 25cm (for EAP783 / EAP650-Desktop) / 20cm (for other models) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."
For EAP770 / EAP772 / EAP783 / EAP787:
- FCC regulations restrict the operation of this device to indoor use only.
- Operation is prohibited on oil platforms, cars, trains, boats, and aircraft, except for large aircraft flying above 10,000 feet in the 5.925-6.425 GHz band.
- Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.
I.T.E. Power Supply Information
Product Name: I.T.E. Power Supply
Model Numbers: T120100-2B1, T120150-2B1, T120150-2B4, T120200-2B4, T120250-2B4, T535081-2B4
Responsible Party: TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with instructions, it may cause harmful interference to radio communications. No guarantee exists that interference will not occur in a particular installation. If interference occurs, users are encouraged to try to correct it by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
TP-Link Systems Inc. has determined that the equipment shown has been shown to comply with applicable technical standards, FCC part 15. No unauthorized changes are made in the equipment, and it is properly maintained and operated.
Issue Date: 2025-08-11
CE Mark Warning
OPERATING FREQUENCY (the maximum transmitted power)
For EAP610 / EAP613 / EAP603GP-Desktop / EAP610GP-Desktop / EAP650GP-Desktop:
- 2412 MHz - 2472 MHz (20dBm)
- 5150 MHz - 5250 MHz (23dBm)
- 5250 MHz - 5350 MHz (23dBm)
- 5470 MHz - 5725 MHz (30dBm)
For EAP650 / EAP653 / EAP670 / EAP673 / EAP650-Desktop / EAP720 / EAP723:
- 2402 MHz - 2480 MHz (10dBm)
- 2412 MHz - 2472 MHz (20dBm)
- 5150 MHz - 5250 MHz (23dBm)
- 5250 MHz - 5350 MHz (23dBm)
- 5470 MHz - 5725 MHz (30dBm)
For EAP770 / EAP772 / EAP783 / EAP787:
- 2402 MHz - 2480 MHz (10dBm)
- 2412 MHz - 2472 MHz (20dBm)
- 5150 MHz - 5250 MHz (23dBm)
- 5250 MHz - 5350 MHz (23dBm)
- 5470 MHz - 5725 MHz (30dBm)
- 6105MHz - 6425 MHz (23dBm)
EU Declaration of Conformity
TP-Link declares that the access point is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when used at 20cm from the body.
National Restrictions
For EAP610 / EAP613 / EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP603GP-Desktop / EAP610GP-Desktop / EAP650GP-Desktop / EAP650-Desktop:
- Frequency band: 5150 - 5250 MHz: Indoor use only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.
- Frequency band: 5250 - 5350 MHz: Indoor use only. Installations and use in road vehicles, trains, and aircraft are not permitted. Outdoor use is not permitted.
- Frequency band: 5470 - 5725 MHz: Installations and use in road vehicles, trains, and aircraft, and use for unmanned aircraft systems (UAS) are not permitted.
For EAP770 / EAP772 / EAP783 / EAP787:
- Frequency band: 5150 - 5250 MHz: Indoor use only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.
- Frequency band: 5250 - 5350 MHz: Indoor use only. Installations and use in road vehicles, trains, and aircraft are not permitted. Outdoor use is not permitted.
- Frequency band: 5470 - 5725 MHz: Installations and use in road vehicles, trains, and aircraft, and use for unmanned aircraft systems (UAS) are not permitted.
- Frequency band 5945-6425MHz: Restricted to indoor use, including in trains with metal-coated windows and aircraft. Outdoor use, including in road vehicles, is not permitted.
UKCA Mark
UK Declaration of Conformity
TP-Link declares that the access point is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.
National Restrictions
Attention: This device may only be used indoors in Great Britain.
Canadian Compliance Statement
For EAP610 / EAP613 / EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP770 / EAP772 / EAP783 / EAP787 / EAP610GP-Desktop / EAP650-Desktop:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
French Translation:
Pour EAP610 / EAP613 / EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP770 / EAP772 / EAP783 / EAP787 / EAP610GP-Desktop / EAP650-Desktop:
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
- L'appareil ne doit pas produire de brouillage;
- L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Caution
For EAP610 / EAP613 / EAP610GP-Desktop:
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
For EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP770 / EAP772 / EAP783 / EAP787 / EAP650-Desktop / EAP603GP-Desktop / EAP650GP-Desktop:
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
- DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz.
Avertissement (French)
Pour EAP610 / EAP613 / EAP610GP-Desktop:
- Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
Pour EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP770 / EAP772 / EAP783 / EAP787 / EAP650-Desktop / EAP603GP-Desktop / EAP650GP-Desktop:
- Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
- Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250-5350 MHz, 5470-5600MHz et 5650-5725MHz.
For EAP770 / EAP772 / EAP783:
- Devices shall not be used for control of or communications with unmanned aircraft systems.
- Operation shall be limited to indoor use only.
- Operation on oil platforms, automobiles, trains, maritime vessels and aircraft shall be prohibited except for on large aircraft flying above 3,048 m (10,000 ft).
French Translation:
Pour EAP770 / EAP772 / EAP783:
- Les appareils ne doivent pas être utilisés pour le contrôle ou la communication avec des systèmes d'aéronefs sans pilote.
- Le fonctionnement doit être limité à une utilisation en intérieur uniquement.
- L'opération sur les plates-formes pétrolières, les automobiles, les trains, les navires maritimes et les avions est interdite, sauf sur les gros avions volant au-dessus de 3 048 m (10 000 ft).
For EAP787:
- Devices shall not be used for control of or communications with unmanned aircraft systems.
- Operation shall be limited to indoor use only.
- Operation on oil platforms, automobiles, trains, maritime vessels and aircraft shall be prohibited except for on large aircraft flying above 3,048 m (10,000 ft).
The antenna is fixed and inside the product, antenna height is equal to product height, which is determined by installers. This information shall be stored internally in the device. Provision of accurate device information is mandatory.
Antenna Type | Model |
---|---|
PIFA | 6035500232, 6035500233 |
French Translation:
Pour EAP787:
- Les appareils ne doivent pas être utilisés pour le contrôle ou la communication avec des systèmes d'aéronefs sans pilote.
- Le fonctionnement doit être limité à une utilisation en intérieur uniquement.
- L'opération sur les plates-formes pétrolières, les automobiles, les trains, les navires maritimes et les avions est interdite, sauf sur les gros avions volant au-dessus de 3 048 m (10 000 ft).
L'antenne est fixe et à l'intérieur du produit, la hauteur de l'antenne est égale à la hauteur du produit, qui est déterminée par les installateurs. Ces informations doivent être stockées en interne dans l'appareil. La fourniture d'informations précises sur l'appareil est obligatoire.
Type d'antenne | Modèle |
---|---|
PIFA | 6035500232, 6035500233 |
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm (for EAP650 / EAP653 / EAP670 / EAP673 / EAP783 / EAP650-Desktop) / 26cm (for EAP770 / EAP772) / 20cm (for other models) between the radiator & your body.
French Translation:
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 25cm (pour EAP650 / EAP653 / EAP670 / EAP673 / EAP783 / EAP650-Desktop) / 26cm (pour EAP770 / EAP772) / 20cm (pour les autres modèles) de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES (B)/NMB (B)
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意!
取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
前述合法通信,指依電信管理法規定作業之無線電通信。
低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact TP-Link.
Do not use a damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed.
For products with power supplies: Adapter shall be installed near the equipment and shall be easily accessible.
For products with power supplies: Use only power supplies provided by the manufacturer and in the original packing of this product. If you have any questions, please contact TP-Link.
Operating Temperature: 0°C ~ 40°C (32 °F ~ 104 °F)
This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.
Please read and follow the above safety information when operating the device. TP-Link cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.
Symbol | Explanation |
---|---|
[Class II equipment symbol] | Class II equipment |
[Class II equipment with functional earthing symbol] | Class II equipment with functional earthing |
[Alternating current symbol] | Alternating current |
[Direct current symbol] | Direct current |
[Polarity of d.c. power connector symbol] | Polarity of d.c. power connector |
[Indoor use only symbol] | For indoor use only |
[Dangerous voltage symbol] | Dangerous voltage |
[Caution, risk of electric shock symbol] | Caution, risk of electric shock |
[Energy efficiency Marking symbol] | Energy efficiency Marking |
[Protective earth symbol] | Protective earth |
[Earth symbol] | Earth |
[Frame or chassis symbol] | Frame or chassis |
[Functional earthing symbol] | Functional earthing |
[Caution, hot surface symbol] | Caution, hot surface |
[Caution symbol] | Caution |
[Operator's manual symbol] | Operator's manual |
[Stand-by symbol] | Stand-by |
[ON/OFF push-push symbol] | "ON"/"OFF" (push-push) |
[Fuse symbol] | Fuse |
[Fuse is used in neutral N symbol] | Fuse is used in neutral N |
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Caution: Avoid listening at high volume levels for long periods.
[Disconnection symbol]: Disconnection, all power plugs
[Mini-gap construction symbol]: Switch of mini-gap construction
[Micro-gap construction symbol]: Switch of micro-gap construction (for US version)
[Micro-disconnection construction symbol]: Switch of micro-gap / micro-disconnection construction (for other versions except US)
[Semiconductor switching device symbol]: Switch without contact gap (Semiconductor switching device)
Mounting Requirements
For safety, TP-Link recommends using the original screws in the package when mounting. The following are alternatives to mount the device on the wall:
- For EAP610 / EAP613 / EAP650 / EAP653 / EAP670 / EAP673 / EAP720 / EAP723 / EAP770 / EAP772 / EAP787: Use 4 screws which comply with ANSI B1.1 4# standard and are longer than 15 mm.
- For EAP783: Use 6 screws which comply with ANSI B1.1 4# standard and are longer than 15 mm.
- For EAP603GP-Desktop / EAP610GP-Desktop / EAP650GP-Desktop / EAP650-Desktop: Use 2 screws which comply with ANSI B1.1 4# standard and are longer than 15 mm.
Screw Specifications:
ANSI B1.1 | Diameter d(mm) | Screw Head Diameter dk (mm) | Screw Head Thickness k (mm) | ||
---|---|---|---|---|---|
min | max | min | max | ||
4# | 2.84 | 5.56 | 5.207 | 2.032 | 1.778 |
6# | 3.51 | 6.858 | 6.5 | 2.464 | 2.21 |
8# | 4.17 | 8.179 | 7.772 | 2.921 | 2.667 |
Description of screw head recess: This type of recess has a large center opening, tapered wings, and blunt bottom, with all edges relieved or rounded.