TP-Link Omada Indoor/Outdoor EAP Regulatory Compliance and Safety Information

FCC Compliance Information Statement

Product Name: Omada Indoor/Outdoor Access Point

Model Numbers: EAP110-Outdoor, EAP113-Outdoor, EAP225-Outdoor, EAP610-Outdoor, EAP623-Outdoor HD, EAP625-Outdoor HD, EAP650-Outdoor, EAP668-Outdoor HD, EAP772-Outdoor, EAP650 D30-Outdoor, EAP650 D120-Outdoor, EAP115-Bridge, EAP211-Bridge, EAP215-Bridge

I.T.E. Power Supply Models: T240025-2-POE (EAP110-Outdoor), T240050-2-POE (EAP225-Outdoor, EAP115-Bridge, EAP211-Bridge, EAP215-Bridge), T480050-2-POE (EAP610-Outdoor), T480038-2-POE (EAP650-Outdoor)

Responsible Party: TP-Link Systems Inc., 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, try to correct the interference by:

Reorienting or relocating the receiving antenna.
Increasing the separation between the equipment and receiver.
Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consulting the dealer or an experienced radio/TV technician.

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

For compliance, antennas must be installed to provide a separation distance of at least 25cm (for EAP610-Outdoor) / 37cm (for EAP650 D120-Outdoor / EAP650 D30-Outdoor) / 20cm (for other models) from all persons.

For EAP772-Outdoor: Operation is prohibited on oil platforms, cars, trains, boats, and aircraft. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

[FCC Logo]

CE Mark Warning

[CE Mark]

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Operating Frequency (Maximum Transmitted Power)

Model(s)	Frequency Band	Max Transmitted Power
EAP110-Outdoor / EAP113-Outdoor	2412MHz-2472MHz	20dBm
EAP225-Outdoor / EAP610-Outdoor / EAP623-Outdoor HD / EAP650-Outdoor	2412MHz-2472MHz	20dBm
	5150MHz-5250MHz	23dBm
	5250MHz-5350MHz	23dBm
	5470MHz-5725MHz	30dBm
EAP625-Outdoor HD / EAP668-Outdoor HD / EAP650 D30-Outdoor / EAP650 D120-Outdoor	2402 MHz-2480 MHz	10dBm
	2412MHz-2472MHz	20dBm
	5150MHz-5250MHz	23dBm
	5250MHz-5350MHz	23dBm
	5470MHz-5725MHz	30dBm
EAP772-Outdoor	2402 MHz-2480 MHz	10dBm
	2412MHz-2472MHz	20dBm
	5150MHz-5250MHz	23dBm
	5250MHz-5350MHz	23dBm
	5470MHz-5725MHz	30dBm
	5945MHz-6425 MHz	23dBm
EAP115-Bridge / EAP211-Bridge / EAP215-Bridge	5150MHz-5250MHz	23dBm
	5250MHz-5350MHz	23dBm
	5470MHz-5725MHz	30dBm

EU Declaration of Conformity

For EAP110-Outdoor, EAP225-Outdoor, EAP610-Outdoor, EAP650-Outdoor, EAP115-Bridge, EAP211-Bridge, EAP215-Bridge: TP-Link declares compliance with essential requirements and provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

For EAP113-Outdoor, EAP623-Outdoor HD, EAP625-Outdoor HD, EAP668-Outdoor HD, EAP772-Outdoor, EAP650 D30-Outdoor, EAP650 D120-Outdoor: TP-Link declares compliance with essential requirements and provisions of directives 2014/53/EU, 2011/65/EU and (EU)2015/863.

The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/.

RF Exposure Information (EU): This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields. The device complies with RF specifications when used at 20cm from your body.

UKCA Mark & Declaration of Conformity

[UKCA Mark]

TP-Link declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.

The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

National Restrictions (Great Britain):

For EAP225-Outdoor, EAP610-Outdoor, EAP623-Outdoor HD, EAP625-Outdoor HD, EAP650-Outdoor, EAP668-Outdoor HD, EAP650 D30-Outdoor, EAP650 D120-Outdoor, EAP115-Bridge, EAP211-Bridge, EAP215-Bridge: Operation in the 5150MHz - 5350MHz frequency range is only permitted indoors.
For EAP772-Outdoor: Operation in the 5150MHz - 5350MHz and 5945-6425MHz frequency ranges is only permitted indoors.

National Restrictions (General EU)

For EAP225-Outdoor / EAP610-Outdoor / EAP623-Outdoor HD / EAP625-Outdoor HD / EAP650-Outdoor / EAP668-Outdoor HD / EAP650 D30-Outdoor / EAP650 D120-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge:

5150 - 5250 MHz: Indoor use only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.
5250 - 5350 MHz: Indoor use only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.
5470 - 5725 MHz: Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

For EAP772-Outdoor:

5150 - 5250 MHz: Indoor use only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.
5250 - 5350 MHz: Indoor use only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.
5470 - 5725 MHz: Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.
5945 - 6425MHz: Restricted to indoor use, including in trains with metal-coated windows and aircraft. Outdoor use, including in road vehicles, is not permitted.

Canadian Compliance Statement

For EAP110-Outdoor, EAP225-Outdoor, EAP610-Outdoor, EAP623-Outdoor HD, EAP625-Outdoor HD, EAP650-Outdoor, EAP668-Outdoor HD, EAP772-Outdoor, EAP650 D30-Outdoor, EAP650 D120-Outdoor, EAP215-Bridge:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada Statement: CAN ICES-3 (B)/NMB-3(B)

Antenna Information for Canadian Compliance:

For EAP110-Outdoor: Two 2.4GHz 3dBi external omnidirectional antennas.
For EAP225-Outdoor: Two 2.4GHz 3dBi external omnidirectional antennas; Two 5GHz 4dBi external omnidirectional antennas.
For EAP625-Outdoor HD: Two 2.4GHz 3dBi external omnidirectional antennas; Two 5GHz 5dBi external omnidirectional antennas.
For EAP668-Outdoor HD: Four 2.4GHz 5dBi external omnidirectional antennas; Four 5GHz 7dBi external omnidirectional antennas.
For EAP772-Outdoor: Alford: 3101507199; Dipole: 3101507197, 3101507198; Franklin: 3101507195, 3101507196; IFA: EAP772OD-BLE-ANT, EAP772OD-GPS-ANT.

Radiation Exposure Statement (Canada): This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm (for EAP772-Outdoor) / 25cm (for EAP610-Outdoor) / 22cm (for EAP625-Outdoor HD) / 22cm (for EAP650 D120-Outdoor / EAP650 D30-Outdoor) / 20cm (for other models) between the radiator & your body.

Other Compliance and Warnings

Korean Warning Statements: This wireless equipment may cause radio interference during operation.

NCC Notice & BSMI Notice (Taiwan):

Do not alter frequency, increase power, or change original design characteristics without approval.
Do not affect flight safety or interfere with legal communications. If interference occurs, stop use and improve until no interference.
Legal communications refer to radio communications regulated by telecommunications management law.
Low-power radio frequency equipment must tolerate interference from legal communications or industrial, scientific, and medical equipment.
For EAP115-Bridge / EAP211-Bridge / EAP215-Bridge / EAP610-Outdoor / EAP623-Outdoor HD / EAP650-Outdoor / EAP772-Outdoor / EAP650 D30-Outdoor / EAP650 D120-Outdoor: Avoid affecting nearby radar systems.
For EAP225-Outdoor / EAP625-Outdoor HD: Avoid affecting nearby radar systems.
High-gain directional antennas are only permitted for fixed point-to-point systems.

RoHS Compliance (China): The table indicates the presence of restricted substances (Pb, Cd, Hg, CrVI, PBB, PBDE) in product components (PCB, Enclosure, Antenna, Other accessories). 'Exceeds 0.1 wt %' or 'Exceeds 0.01 wt %' indicates the substance percentage exceeds the threshold; '○' indicates the percentage does not exceed the threshold; '—' indicates it is an exclusion item.

Safety Information

Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
(For models with adapters) Adapter should be used indoors where the ambient temperature is lower than or equal to 40°C.
Do not attempt to disassemble, repair, or modify the device. Contact TP-Link for service.
Do not use damaged chargers or USB cables. Use only recommended chargers.
Do not use the device where wireless devices are not allowed.
(For models with adapters) Adapter shall be installed near the equipment and be easily accessible.
(For models with adapters) Use only power supplies provided by the manufacturer in the original packing.
Operating Temperatures:

EAP113-Outdoor: -30°C – 65°C (-22 °F – 149 °F)
EAP115-Bridge / EAP211-Bridge / EAP215-Bridge: -40°C – 70°C (-40 °F – 158 °F)
EAP668-Outdoor HD: -40°C – 65°C (-40 °F – 149 °F)
For others: -30°C – 70°C (-22 °F – 158 °F)

This product emits electromagnetic fields. Keep the product and power adapter more than 15 cm (6 inches) away from pacemakers or other implanted medical devices. If interference is suspected, turn off the product and consult a physician.
Please read and follow safety information. Use this product with care and at your own risk.

Explanation of Symbols on Product Label

Symbol	Explanation
[Class II equipment symbol]	Class II equipment
[Class II equipment with functional earthing symbol]	Class II equipment with functional earthing
[Alternating current symbol]	Alternating current
[Direct current symbol]	Direct current
[Polarity of d.c. power connector symbol]	Polarity of d.c. power connector
[For indoor use only symbol]	For indoor use only
[Dangerous voltage symbol]	Dangerous voltage
[Caution, risk of electric shock symbol]	Caution, risk of electric shock
[Energy efficiency Marking symbol]	Energy efficiency Marking
[Protective earth symbol]	Protective earth
[Earth symbol]	Earth
[Frame or chassis symbol]	Frame or chassis
[Functional earthing symbol]	Functional earthing
[Caution, hot surface symbol]	Caution, hot surface
[Caution symbol]	Caution
[Operator's manual symbol]	Operator's manual
[Stand-by symbol]	Stand-by
["ON"/"OFF" (push-push) symbol]	"ON"/"OFF" (push-push)
[Fuse symbol]	Fuse
[Fuse is used in neutral N symbol]	Fuse is used in neutral N
[WEEE Recycling Symbol]	This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). It must be handled pursuant to European directive 2012/19/EU for recycling or dismantling to minimize environmental impact. Users can give the product to a competent recycling organization or retailer.
[Caution, avoid listening at high volume levels for long periods symbol]	Caution, avoid listening at high volume levels for long periods
[Disconnection, all power plugs symbol]	Disconnection, all power plugs
[Switch of mini-gap construction symbol]	Switch of mini-gap construction
[Switch of micro-gap construction (for US version) symbol]	Switch of micro-gap construction (for US version)
[Switch of micro-gap / micro-disconnection construction (for other versions except US) symbol]	Switch of micro-gap / micro-disconnection construction (for other versions except US)
[Switch without contact gap symbol]	Switch without contact gap (Semiconductor switching device)

Installation and Mounting Requirements

Professional Installation Instruction: This product is designed for specific applications and needs to be installed by a qualified person with RF and related rule knowledge. It requires professional configuration by an SDN Controller network service before use.

Professional Installation Requirements:

Generally for industrial/commercial use, sold only to authorized dealers or installers.
During installation, ensure the equipment is perpendicular to the ground.
Operation in the 5150-5250MHz is restricted to indoor use only.
Operation in the 5600-5650MHz band is prohibited.

Specific Restrictions for Bands:

For EAP225-Outdoor / EAP610-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge: Operation in the 5150–5250 MHz band is for indoor use only to reduce interference to mobile satellite systems. 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
For EAP623-Outdoor HD / EAP650-Outdoor / EAP772-Outdoor / EAP650 D30-Outdoor / EAP650 D120-Outdoor: Operation in the 5150–5250 MHz band is for indoor use only to reduce interference to mobile satellite systems. 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
For EAP625-Outdoor HD / EAP668-Outdoor HD: Operation in the 5150–5250 MHz band is for indoor use only to reduce interference to mobile satellite systems. 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong. Maximum antenna gain for detachable antennas in 5250-5350 MHz and 5470-5725 MHz bands must comply with EIRP limits. Maximum antenna gain for detachable antennas in the 5725-5850 MHz band must comply with EIRP limits for point-to-point and non-point-to-point operation.

Mounting Requirements: Use original screws. Alternatives for wall mounting:

For EAP610-Outdoor / EAP623-Outdoor HD / EAP625-Outdoor HD / EAP650-Outdoor: Use 2 screws complying with ANSI B1.1 4#, (5#), 6# standard, longer than 7 mm.
For EAP772-Outdoor / EAP650 D30-Outdoor / EAP650 D120-Outdoor: Use 4 screws complying with ANSI B1.1 4#, (5#), 6# standard, longer than 7 mm.
For EAP668-Outdoor HD: Use 2 expansion screws complying with ANSI B1.1 standard with a diameter of 3/8 or 7/16 inches and longer than 60 mm.

	TP-Link Omada Indoor/Outdoor EAP Series: Regulatory Compliance and Specifications Detailed regulatory compliance information for TP-Link Omada Indoor/Outdoor Access Points (EAPs), including FCC, CE, UKCA, IC statements, operating frequencies, RF exposure limits, national restrictions, and safety guidelines.
	TP-Link Omada Outdoor Access Point Regulatory Compliance and Specifications Comprehensive regulatory compliance information, FCC, CE, UKCA, IC, and other regional statements for TP-Link Omada Outdoor Access Points including EAP110, EAP113, EAP225, EAP610, EAP650, EAP115, EAP211, EAP215 models.
	TP-Link Omada Indoor/Outdoor EAP Regulatory Compliance Information This document outlines the essential regulatory compliance, FCC, EU, and Canadian statements, national restrictions, and safety guidelines for TP-Link Omada Indoor/Outdoor Access Points (EAPs).
	TP-Link Omada Business Cloud SDN Solution: Wi-Fi 6 Access Points Explore the TP-Link Omada Business Cloud SDN Solution, featuring a comprehensive range of Wi-Fi 6 and Wi-Fi 6E Access Points designed for seamless, high-density wireless connectivity in various business environments. Discover features like centralized cloud management, zero-touch provisioning, AI-driven technology, and robust security.
	TP-Link Omada Business Wi-Fi 6 & 6E Access Points and SDN Solution Discover TP-Link's Omada Business Wi-Fi 6 and Wi-Fi 6E Access Points and the Omada Software Defined Networking (SDN) solution for scalable, centralized cloud management, offering high performance, security, and reliability for businesses.
	TP-Link Omada Outdoor Access Point Regulatory Compliance Information This document provides essential regulatory compliance details for TP-Link Omada Outdoor Access Points, covering FCC, CE, and Industry Canada standards, RF exposure, and safety guidelines for models like EAP110, EAP225, EAP610, and EAP650.
	TP-Link Omada EAP Indoor/Outdoor Access Point Quick Installation Guide This guide provides instructions for the quick installation of TP-Link Omada EAP indoor/outdoor access points, covering package contents, hardware installation, and software configuration.
	TP-Link Omada Indoor/Outdoor Access Point Quick Installation Guide A guide to installing and configuring TP-Link Omada Indoor/Outdoor Access Points, covering package contents, hardware installation, and software configuration via the Omada App or web browser.

TP-Link Omada Indoor/Outdoor EAP Regulatory Compliance