RC10B7 Team Kit Setup Sheet and Specifications
Driver: Olly Frost | Date: July 25 | Event: Midwest | Track: Coventry | Qualify: | Finish: | Main: | Best Lap Time:
Brand: Team Associated
Model: RC10B7 Team Kit
Front Suspension
General Settings
Ride Height: 16
Camber: 1.5
Toe: just out
Anti-Roll Bar: none
Arm Type: carbon
Tower Type: kit
Wheel Hex: 5
Steering Block KPI: b6.1
Adjustment Points
Ball Stud Spacing (Front Upper): 3
Ball Stud Spacing (Front Lower): 0
Ball Stud Spacing (Steering): 1
Bump Steer Spacing: 0
Steering Plate: +!
Ball Stud Spacing (Steering Link): 2
Ball Stud Spacing (Steering Link): 1
Caster Block Insert: 0 [ +2.5 ] [ +5 ]
Bulkhead Type: Ali
Kick-Up Angle: -2.5 [ 0 ] [ +2.5 ]
Steering Stop Spacing: [none]
Caster Block Spacing: Fwd [ Back ]
Diagram Description: Front suspension assembly showing adjustable ball stud positions, steering block KPI, caster block inserts, and kick-up angle options.
Rear Suspension
General Settings
Ride Height: 17
Camber: 1.5
Anti-Roll Bar: none
Arm Type: plastic
Tower Type: kit
Adjustment Points
Arm Spacing: Fwd [ Mid ] [ Back ]
Wheel Hex: 5
Hub Type: Std [x] HRC [ ]
Hub Spacing: Fwd [ Mid ] [ Back ]
Drive Shaft: CVA's [ ] Universals [x]
C Mount: Aluminum [x] Steel [ ]
D Mount: Aluminum [x] Steel [ ]
Camber Link Spacing: 1
Ball Stud Spacing (Camber Link): 1
Ball Stud Spacing (Camber Link): 2
Axle Height Options:
- [ ] +3
- [x] +2
- [x] +1
- [ ] +0
Caster Block Link Mount: CBA
Front Bulkhead Spacing: CBA
Diagram Description: Rear suspension assembly showing C and D mount options, camber link adjustments, and axle height selection.
Electronics
Radio:
Servo:
EPA Throttle:
% Brake:
ESC:
ESC Settings:
Motor/Wind: Reedy 7.0
Timing:
Pinion: 22
Spur:
Battery Mount: Std [x] Offset [ ]
Battery: reedy 4600
Weight: 50g
Notes:
Drivetrain
Differential: Ball Diff [ ] Gear Diff [x]
Height: 1
Diff Setting: 15k 2 Gear
Notes:
Shocks
| Parameter | Front | Rear |
|---|---|---|
| Piston | 2*1.8 | 2*1.9 |
| Thickness | 2.5 | 2.5 |
| Fluid | 37.5 | 27.5 |
| Spring | v3 Orange | v3 Yellow |
| Stroke | 23 | 27 |
Slipper Clutch
Type: kit dirt
# of Pads: 2
Setting: vented
Notes:
Other Adjustments
Limiters: Int: [ Ext: ] Int: [ Ext: ]
Eyelet: 0 [ 2 ]
Cup Offset: 0 [ +5 ] [ +9 ] 0 [ +5 ] [ +9 ]
Kashima Bodies [ ] Chrome Shafts [ ] Machined Spacers [x]
Notes:
Diagram Description: Shock absorber components showing piston, thickness, fluid, spring, and stroke options. Slipper clutch details and other shock adjustments like limiters and cup offset.
Track Info
Size:
Surface:
Traction:
Moisture:
Condition:
Temperature:
Notes:
Tires
Front Tires: cut stagger
Front Compound: yellow
Front Insert: none
Rear Tires: Mezzo
Rear Compound: yellow
Rear Insert: cheater
Wheel (F/R): centro
Notes: fronts glued down and sidewall
Body & Weight
Body: kit
Front Wing: kit
Rear Wing: kit
Wing Angle: 0° [ 3° ] [ 6° ]
Chassis Length:
Servo Weights:
Electronic Weights: kit
Total Vehicle Weight:
Notes:
Vehicle Comments
Notes:
For more setups, visit: https://www.associatedelectrics.com/teamassociated/manuals_and_setup_sheets/
