SEPLOS Battery Monitor Installation Guide
Dongguan Seplos Technology Co., Ltd
Software Installation and Setup
-
Unzip the Battery Monitor file
Locate the
BatteryMonitor V2.1.9.zipfile. -
Run the application
Open the unzipped folder, find the
BatteryMonitor.exeapplication file, and double-click to run the software.The folder structure typically includes directories for languages, logs, and real-time records.
-
Import Protocol
Click 'import protocol'. Navigate to and select the 'Agreement' file. Choose the corresponding agreement file (ending in 'EN' for the English version). Click 'open', then click 'confirm'.
The software interface will display various parameters and settings, including cell voltage, battery voltage, current, SOC, and temperature information.
-
Connect to Device
Select the correct port number (usually identified automatically for USB to RS485 adapters). Set the baud rate to 19200. Click 'Connect'.
Upon successful connection, battery information will be displayed.
-
Login
Use the default login credentials: Username:
admin, Password:admin. -
Parameter Management
Upload Parameter: Click 'upload parameter' to upload settings to the software. This is necessary when running the software for the first time.
Load Parameter: Click 'load parameter' to load settings from the software. After uploading, it is recommended to load parameters.
Modify Parameter: Click 'upload parameter' again to modify existing parameters or turn functions on/off. Click 'Set all' to save the modifications.
-
Load Parameter (Confirmation)
Click 'load parameter' and then 'open' to load a parameter file. Ensure the selected file is a valid parameter file (.xml).
Communication Protocol Configuration
The software supports various communication protocols compatible with different inverters:
| Protocol Type | Compatible Inverter |
|---|---|
| PN-GDLT | Pylontech/Goodwe/TBB/Luxpower/DEYE |
| GRWT | Growatt SPF/SPH |
| VCTR | Victron |
| SMA-SF | SMA/SOFAR |
| GINL | Solis |
| Studer | Studer |
To configure the communication protocol:
- Click the pull-down menu for 'CAN'.
- Choose the corresponding protocol based on your inverter manufacturer.
- Click 'Close' to refresh the software. The correct inverter manufacturer information should then be displayed.
Software Interface Overview
The SEPLOS Battery Monitor software provides a comprehensive interface for monitoring battery status. Key interface specifications include:
| Item | Introduction | Remark |
|---|---|---|
| Max voltage | The maximum cell voltage value | |
| Min voltage | The minimum cell voltage value | |
| Voltage difference | The voltage difference between the highest and lowest cell | |
| Battery voltage | Battery pack voltage | |
| Current | Charging/discharging current (-*) | configurable |
| Remaining capacity | The remaining capacity | |
| Total capacity | The real capacity of the battery pack | |
| SOC | State of charge | |
| Rated capacity | Rated capacity | configurable |
| Battery cycles | 80% DOD for one cycle | |
| SOH | State of health | |
| BUS voltage | BUS bar voltage | |
| Discharge switch | Discharge indicator | Green: ON |
| Charging switch | Charge indicator | Grey: OFF |
| Current limit switch | Current limit indicator | |
| Temperature control switch | Temperature control indicator | |
| Warn and protect | Battery status | |
| Battery temp1 | Temperature value of cell 1 | |
| Battery temp2 | Temperature value of cell 2 | |
| Battery temp3 | Temperature value of cell 3 | |
| Battery temp4 | Temperature value of cell 4 | |
| Ambient temp | Ambient temperature | |
| Power temp | MOSFET temperature |
Parallel Connection
The SEPLOS Battery Monitor supports a maximum of 16 packs connected in parallel. Ensure the corresponding pack number is selected based on DIP address settings within the software.
- The paralleled pack quantity will be displayed.
- Selecting 'cycle fresh' will display information for all paralleled packs in turn.
- Clicking 'multiple' will display details for all packs on a single page.
Energy Storage Battery Manufacturer – Seplos Technology
