Aiper Scuba X1 Pro Cordless Robotic Pool Cleaner

Important Safety Instructions

Please read this user manual carefully and follow all warnings and instructions for operating the Aiper cordless robotic pool cleaner (hereinafter referred to as the "device"). Failure to follow these instructions may result in electric shock, fire, or serious injury. Aiper is not responsible for any loss or injury caused by improper use of this device.

For your safety and optimal performance, please follow these instructions:

1. This device is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or persons lacking experience and knowledge, unless they are supervised by a person responsible for their safety or have been instructed on how to use the device.
2. Children must not play with this device. Children must not perform maintenance on this device without supervision.
3. Children should be supervised to ensure they do not play with the device.
4. Ensure that children do not attempt to touch the operating device.
5. Under no circumstances should children be allowed to ride on the device.
6. Do not operate the device when people or animals are in the pool.
7. When the device is operating, do not put your hands into any part of it, as you may get injured.
8. Do not operate the device when it is dry, as it may overheat.
9. Using a charger with a different battery than the one it is intended for poses a fire risk.
10. WARNING: Only use the detachable power unit supplied with this device to recharge the battery.
11. This device uses a 24-cell lithium battery with a DC voltage of 21.6 V and a capacity of 10,400 mAh, compatible with charger model GM95-252300-2FGN. Before disposing of the device, you must remove the battery and dispose of it in accordance with local laws and regulations.
12. This device may only be used with lithium batteries of model number C1264C6.
13. The batteries in this device can only be replaced by qualified personnel. If you need to replace the battery in the device, contact customer service.
14. The batteries in this device are not replaceable. When the battery reaches the end of its lifespan, the device must be properly disposed of.
15. When using a battery-powered device, be aware of the risk of short-circuiting the battery terminals or the battery itself with metal objects.
16. If unknown liquid leaks from a damaged device, do not touch it. If you come into contact with the liquid, especially if it splashes into your eyes or other sensitive body parts, immediately flush the affected area with water. Liquid that leaks from a damaged battery may cause skin irritation or burns.
17. Do not expose the device or battery to fire or excessively high temperatures. Exposure to fire or temperatures above 130 °C (265 °F) may cause an explosion.
18. If you are disposing of the device and need to remove the battery, disconnect the device from the charger and switch the device to the OFF position.
19. Before disposing of the device, you must remove the battery and dispose of it in accordance with local laws and regulations.
20. Dispose of a faulty battery according to your local regulations.
21. Do not incinerate the device, even if it is significantly damaged. Batteries can explode in a fire.
22. Before charging, ensure that your device is turned off and the charging port is dry. Your device should be in a cool, well-ventilated place while charging. Do not cover the device during charging, as this may cause overheating of its components.
23. WARNING: If the cable is damaged, replace it immediately to reduce the risk of electric shock.
24. If the power cable is damaged, it must be replaced or repaired by a qualified electrician or Aiper customer service representative to prevent the risk.
25. In case of damage or malfunction of the power supply, this supply must not be repaired or used further.
26. The sealed power unit of your device may only be disassembled by certified technicians.
27. Use the device only as described in this manual. Use only accessories recommended or sold by the manufacturer.
28. Do not use the device simultaneously with other pool equipment, such as pool filters, vacuums, or skimmers.
29. When placing the device in water, the front of the device must face upwards. Never place the device upside down or throw it into the pool.
30. When working near the pool, be careful where you step and maintain your balance.
31. Do not drop the device on the ground, puncture its casing, or intentionally damage it in any way, as this may void the warranty.
32. To avoid exposure to RF radiation, maintain a distance of 20 cm or more between people operating the device and the device itself. Operation at a shorter distance is not recommended. The antenna used for the transmitter of this device must not be located in the same place as another antenna or transmitter.
33. Before performing user maintenance, such as cleaning the filter, disconnect the robotic pool cleaner from the power supply.
34. Before cleaning or maintaining the charger, the plug must be removed from the socket.
35. If you will not be using the charger for an extended period, unplug it.
36. When the device is not in use, store it indoors in a cool, well-ventilated place.

Product Components

2.1 Package Contents

• Robotic Pool Cleaner *1
• Charging Station *1
• User Manual *1
• Charger *1
• Hook *1
• Quick Start Guide *1

2.2 Component Overview

Robotic Pool Cleaner (side view)

• 1. Top Cover
• 2. WiFi Indicator
• 3. Power Button
• 4. Handle
• 5. Roller Brush
• 6. Filter Box
• 7. Status LED Indicator
• 8. OmniSense™ Sensor
• 9. Track

How to Use Your Aiper Scuba X1 Pro

3.1 Operating Conditions

Ensure the device is used only under the specified pool conditions. Damage caused by use outside the specified conditions is not covered by the warranty.

3.2 App Download

To access new features of your device, download the Aiper app. You can download and install the Aiper app by scanning the QR code below or by searching for "Aiper" in your app store.

Download on the App Store

GET IT ON Google Play

Notes:

• To ensure the app functions correctly on your phone or device, you need iOS 12.0 or later, or Android 8.0 or later.
• After installing the app, complete the registration, login, and network setup according to the instructions in the app.

3.3 Network Setup

Upon first startup, the device will enter network setup mode. If this process is interrupted, press and hold the buttons + for 5 seconds to re-enter network setup mode.

In network setup mode, select either "Setup via Bluetooth" or "Setup via QR Code".

• Setup via Bluetooth: Enable Bluetooth on your phone and grant the Aiper app access. In the app, tap the [+] symbol in the upper right corner and select "Add via Bluetooth". The app will then detect nearby Bluetooth-enabled devices. Select your network, enter the WiFi password, and tap "Next" to complete the network setup.
• Setup via QR Code: Open the app and tap the [+] symbol in the upper right corner. Then select "Add via QR Code". Scan the QR code on your Aiper device. After the device is recognized, follow the in-app instructions to connect to your device's WiFi network. Once connected, return to the app and complete the network setup as instructed.

WiFi Network Requirements: Use a 2.4GHz or 2.4/5GHz mixed network.

3.4 Charging

NOTICE: Fully charge the device before using it to clean the pool. Do not charge the device in direct sunlight.

It is recommended to maintain a distance of at least 3.5 m (11.5 ft) between your pool and the charging station. Ideally, the charging location should have WiFi signal coverage to expedite the installation of remote updates.

Charging Options:

• Charging Station
  1. Charging Station Installation: Insert the supports into the charging panel. Then attach the front cover.
  2. Before charging, ensure that the charging station and the device are dry. Do not charge a wet device at the station. For optimal charging quality, dry the metal contacts on the underside of the device with a paper towel or dry cloth.

3. Connect the charger cable to the charging port on the charging station and plug the adapter into any available socket. Place the dry device on the charging station. The status LED indicator on the device will pulse during charging and turn solid green when fully charged.

Charging Port:

1. Before charging, remove the charging port cover and ensure the charging port is dry. If water or moisture gets into the port, dry it with a clean cloth before proceeding to charge the device.
2. Connect the charger to the device's charging port and then plug the charger into any available socket. The status LED indicator will pulse during charging and turn solid green when fully charged.

3.5 Button Descriptions

The device features several buttons for operation:

• Mode Button: Allows you to change and select the cleaning mode.
• Power Button: Turns the device on and off.
• Cleaning Intensity Button: Allows you to change and select the cleaning intensity.

Combined Button Functions:

• Network Setup Mode: Enter network setup mode by pressing and holding the + buttons simultaneously for 5 seconds. The device will remain in network setup mode for 300 seconds, so complete the setup quickly.
• Factory Reset: To restore the device to factory settings, press and hold the + buttons simultaneously for 5 seconds. This will erase all user settings, cleaning data, and customized settings.

In addition to the cleaning modes indicated, all cleaning mode LED indicators may light up simultaneously, indicating that the device is performing a user task.

3.6 Cleaning Modes

The device offers several cleaning modes:

• Intelligent Mode: The device will progressively clean the pool floor and walls. While cleaning the walls, it will also clean the waterline.
• Floor Mode: The device will clean the pool floor following a "5"-shaped trajectory without cleaning the walls or climbing them.
• Wall Mode: The device will clean the pool walls using a "Y"-shaped trajectory and simultaneously clean the waterline. The pool floor is not cleaned in this mode.
• Waterline Mode: The device will move horizontally and clean the waterline. When the device encounters a corner or obstacle on the pool wall, it will submerge, change walls, or overcome the obstacle and continue cleaning.

Note: The cleaning trajectory used by the device may vary between firmware versions. For the most accurate information, refer to the actual operation of the device or the latest official documentation.

3.7 Cleaning Intensity

You can adjust the cleaning intensity to suit your needs:

• Economy Cleaning: Reduces power consumption and extends battery life.
• Adaptive Cleaning: Automatically adjusts cleaning power based on pool conditions for efficient cleaning and optimal battery life.
• High-Performance Cleaning: Increases cleaning power for heavily soiled pools, but consumes more energy, potentially reducing battery life.

Notes:

• If you are unsure about the level of pool soiling, we recommend using the automatic cleaning intensity. The automatic mode adjusts the cleaning power according to the pool's condition. This ensures efficient cleaning while maintaining optimal battery life for the X1 Pro.
• If the pool water is heavily soiled with visible debris, we recommend using the maximum cleaning intensity. The maximum intensity mode increases cleaning power and energy consumption, which may lead to shorter battery life.
• If the pool water is lightly soiled with minimal visible debris, we recommend using the economy cleaning mode. The economy cleaning mode reduces energy consumption and extends the battery life of the X1 Pro.

3.8 Filter Selection

Two filters with different filtration levels are available: the replaceable ultra-fine MicroMesh™ filter and the filter box.

• The replaceable ultra-fine MicroMesh™ filter can capture particles as small as 3–10 µm, including mud and certain types of algae. When visible debris is minimal (e.g., pebbles, leaves, sand, dirt, hair) and the water is cloudy, or there are some algae, it is recommended to use the filter box with the replaceable ultra-fine MicroMesh™ filter.
• If there is a large amount of visible debris in the water, it is recommended to use only the filter box without the replaceable ultra-fine MicroMesh™ filter.

3.9 Cleaning Process

1. To turn the device on or off, press and hold the ⏻ button for 2 seconds.
2. You can quickly switch between the four available cleaning modes using the ⏻ button and select the most suitable one: Intelligent mode, Floor mode, Wall mode, and Waterline mode.

Once you select the desired cleaning mode, immediately place the device in the pool. After a brief submersion, the device will begin its cleaning task in the selected mode.

3. When the device submerges, upon selecting a mode, including pool floor cleaning, the mapping process will begin. The device will start cleaning along the pool edges and create a map of the floor without climbing the walls.

After successful mapping, the same pool will not need to be mapped again. However, before each cleaning, the device will briefly traverse the floor to determine its location.

After mapping is complete, the device will automatically recognize the pool's shape and begin cleaning the floor along a "5"-shaped trajectory. Once cleaning is finished, the device will return to any areas it missed.

4. Details of the individual cleaning modes are described below:

• Intelligent Mode: The device will progressively clean the pool floor and its walls. While cleaning the walls, it will also clean the waterline.
• Floor Mode: The device will clean the pool floor following a "5"-shaped trajectory, without cleaning the walls or climbing them.
• Wall Mode: The device will clean the pool walls using a "Y"-shaped trajectory and simultaneously clean the waterline. The pool floor is not cleaned in this mode.
• Waterline Mode: The device will move horizontally and clean the waterline. When the device encounters a corner or obstacle on the pool wall, it will submerge, change walls, or overcome the obstacle and continue cleaning.

5. When the device completes its current cleaning task, it will return to the edge of the pool, rise to the water surface, and remain there for 5 minutes. During this time, the user can safely remove the device from the water.

If you leave the device at the waterline for more than 5 minutes without removing it, it will return to the pool floor and stay near the wall. Users can attach the hook to any standard telescopic pool pole (not included) to hook and pull the device from the pool floor.

6. Before storing or charging the device, let all the water drain out.

Maintenance

4.1 Cleaning the Filter Box

1. Place the device on a flat surface and lift the top cover.
2. Remove the filter box by its handle.
3. Press the latch on the filter box and open it by lifting the handle of the top cover.
4. Empty the filter box and remove the replaceable ultra-fine MicroMesh™ filter.

Detach latches A, B, C, and D on the rubber band of the replaceable ultra-fine MicroMesh™ filter from the limiting openings.

5. Rinse the replaceable ultra-fine MicroMesh™ filter and the filter box separately.

The replaceable ultra-fine MicroMesh™ filter must be rinsed inside and out. If necessary, remove any remaining debris by hand.

6. After drying the replaceable ultra-fine MicroMesh™ filter and the filter box, insert the filter into the filter box and place the filter box back into the device.

Ensure that letter A on the filter box corresponds to letter A on the replaceable ultra-fine MicroMesh™ filter.

Progressively pull the corners A, B, C, and D on the rubber band. Ensure they snap into the limiting openings on the replaceable ultra-fine MicroMesh™ filter.

Once inserted, ensure the rubber band is properly seated in the limiting opening.

Notes:

• After each cleaning task, immediately remove the device from the pool and clean the filter box. Do not leave the device in the pool for extended periods.
• Drying the replaceable ultra-fine MicroMesh™ filter and the filter box after each cleaning is not necessary and is recommended solely to prevent mildew odor.
• If you plan to store the device, it is recommended to store it in a well-ventilated area away from direct sunlight. This also applies to the replaceable ultra-fine MicroMesh™ filter and the filter box.
• The replaceable ultra-fine MicroMesh™ filter is capable of capturing particles ranging from 3–10 µm, including mud and certain types of algae. When visible debris is minimal (e.g., pebbles, leaves, sand, dirt, hair) and the water is cloudy, or there are some algae, it is recommended to use the filter box with the replaceable ultra-fine MicroMesh™ filter. If there is a large amount of visible debris in the water, it is recommended to use only the filter box without the replaceable ultra-fine MicroMesh™ filter.
• For cleaning the replaceable ultra-fine MicroMesh™ filter and the filter box, using a high-pressure water cleaner is recommended to ensure thorough cleaning.
• After several uses, the surface of the replaceable ultra-fine MicroMesh™ filter may show signs of wear, but this does not affect its performance.
• The replaceable ultra-fine MicroMesh™ filter is a consumable material that needs to be replaced after 30 uses to maintain filtration efficiency.

4.2 Cleaning the Screw

1. Use a flat-head screwdriver to pry open the drain cover.
2. After removing the drain cover, remove the screw cover so the screw is visible.
3. Remove any debris wrapped around the screw.
4. After cleaning the screw, replace the screw cover and then close it under the drain cover.

4.3 Replacing the Track

1. Remove the side cover plate from the device: Place the device on its side, remove the 4 clips on the side cover plate with a flat-head screwdriver, and pull the side cover plate upwards.
2. Remove the screws and guide sleeve from the rear wheel.
3. Remove the rear wheel and track from the device by carefully pulling each piece out.
4. Align the tabs on the replacement track with the teeth on both wheels. Replace the rear wheel and track so that the wheel fits into the sleeves on the track.
5. Insert the guide sleeve of the rear wheel so that the top of the three shafts fits into the opening on the device.
6. Tighten the screws and replace the side cover. Repeat the same procedure for the other track.

4.4 Replacing the Roller Brush

1. Remove all silicone clips from your current roller brush.
2. After removal, take the replacement roller brush and align the silicone clips with the opening. Push the clips into the respective slots so that the new roller brush fits securely in your device. Repeat the same procedure for the other roller brush.

4.5 Turning Off and Storing the Aiper Device

During the off-season, such as winter, or when the Aiper device will be out of service for an extended period, follow these instructions to maintain the device in good condition:

1. Fully charge the device before storing it. Before storing the device, ensure it is turned off and disconnected from the charger.
2. Thoroughly clean the entire device, including the top and bottom covers, wheels, brushes, and charging port, and remove all dirt.
3. Dry the device with a cloth or soft fabric and ensure the charging port cover is properly closed.
4. Store the device in its original packaging in a cool, dry, and well-ventilated place.
5. To preserve battery life, charge it every six months.

Specifications

Symbols:

• ⌀ DC Current.
• ⌁ AC Current.
• Class II device.
• Switching Power Supply.
• Polarity of DC connector.
• Safety isolating transformer with short-circuit protection.
• For indoor use only.
• If the plug pins are damaged, the power supply must be replaced.
• Refer to the user manual.

LED Indicator

Troubleshooting

Warranty

This product has undergone quality control and safety testing by our technicians.

1. This product comes with a warranty that covers the battery and motor of your device, starting from the date of purchase. Statutory provisions regarding warranty conditions applicable in your country will be followed.
2. This warranty is void if the product is modified or used improperly, or if repairs are carried out by unauthorized personnel.
3. This warranty covers manufacturing defects only and does not cover damage resulting from improper use by the user.
4. To request a warranty repair, you must present the order number or proof of purchase.
5. This is an additional warranty offered by AIPER INTELLIGENT SARL, located at 43-47 avenue de la Grande Armée, 75116 Paris, France. This warranty does not cover free solutions due to non-compliant descriptions claimed by the consumer against the seller by law.
6. Warranty resolution email: service@aiper.com

Declaration of Conformity (CE)

Shenzhen Aiper Intelligent Co., Ltd. hereby declares that this product complies with all the requirements of the applicable European directives 2014/53/EU and 2011/65/EU. The full text of the declaration of conformity is available at the following link:

https://eu.aiper.com/aiper-europe-doc-user-manual/

You can request the EU Declaration of Conformity at the following address:

AIPER INTELLIGENT SARL
43-47 avenue de la Grande Armée, 75116 Paris, France

Recycling Information:

This symbol means that this product should not be treated as household waste. Instead, it should be handed over to the appropriate collection point for the recycling of electrical and electronic equipment.