Electrolux Refrigerator Component Overview
Cabinet Assembly - Part 1
This section details the external cabinet structure and its primary components.
- 1: Main cabinet frame/body
- 2: Door hinge assembly (lower)
- 3: Door hinge assembly (upper)
- 4: Door seal/gasket
- 5: Shelf supports/brackets
- 6: Base/footing assembly
- 7: Top panel
- 8: Back panel (exterior)
- 9: Leveling feet
- 10: Handle mounting hardware
- 11: Door handle attachment point
- 12: Fasteners (screws, bolts)
- 13: Internal shelf mounting rail
- 14: Internal wiring/conduit guides
- 46: Door handle
- 47: Exterior panel/trim
Cabinet Assembly - Part 2
This section illustrates the rear and internal mounting structures of the cabinet.
- 1: Main chassis/base structure
- 14: Terminal block/junction box
- 15: Mounting bracket for electrical components
- 16: Fastener (screw)
- 18: Internal structural support
- 21: Bracket for component mounting
- 22: Fastener (screw)
- 23: Fastener (screw)
- 25: Fastener (screw)
- 26: Mounting plate
- 27: Fastener (screw)
- 28: Rear panel assembly
- 29: Internal mounting bracket
- 30: Base support
- 31: Fastener (screw)
- 32: Internal mounting bracket
- 33: Internal component housing
- 34: Rear panel (internal)
- 35: Mounting bracket
- 36: Frame element
- 37: Wiring guide/clip
- 38: Support rod/bracket
- 39: Mounting bracket
- 40: Fastener (screw)
- 41: Fastener (screw)
- 42: Internal housing/panel
- 43: Internal component mounting plate
- 44: Internal panel
- 45: Cover panel
- 47: Internal bracket
- 49: Fastener (screw)
Refrigerant System
This diagram shows the components of the refrigeration circuit.
- 1: Power cord connector/plug
- 2: Control module housing/mount
- 2A: Compressor
- 3: Compressor mounting grommets/isolators
- 4: Refrigerant tubing
- 5: Refrigerant tubing
- 10: Refrigerant tubing
- 11: Refrigerant tubing
- 12: Refrigerant tubing
- 13: Evaporator/Condenser coil assembly (partially shown)
- 14: Drip tray/evaporation pan
- 15: Mounting bracket for control module
- 16: Fastener (screw)
- 17: Filter drier/accumulator
- 18: Power plug
- 19: Electrical connection point
- 20: Wire harness connector
Cabinet Interior
This section illustrates the internal layout and components of the refrigerator cabinet.
- 1: Ice maker module housing
- 2: Ice maker water inlet connection
- 3: Ice maker mold assembly
- 4: Crisper drawer slide/runner
- 5: Ice maker mechanism components
- 6: Drawer runner/guide
- 7: Upper shelf/glass panel
- 8: Shelf support
- 8A: Shelf support
- 8B: Shelf support
- 9: Drawer front/handle
- 10: Drawer runner/guide
- 11: Drawer runner/guide
- 12: Drawer front/handle
- 13: Main refrigerator shelf
- 14: Ice maker collection bin
- 15: Drawer runner/guide
- 16: Drawer runner/guide
- 17: Drawer runner/guide
- 18: Drawer front/handle
- 19: Crisper drawer
- 20: Ice maker components
- 20A: Ice maker components
- 20B: Ice maker components
- 23: Crisper drawer
Door Assembly
This diagram focuses on the refrigerator door and its internal fittings.
- 1: Door panel
- 2: Door hinge attachment point
- 3: Door gasket/seal
- 4: Door seal/gasket
- 5: Door bin mounting bracket
- 7: Door bin/shelf (upper)
- 8: Door bin/shelf (middle)
- 9: Door bin/shelf (lower)
- 10: Door bin/shelf (lower)
- 11: Door bin/shelf (side)
- 12: Fastener (screw) for hinge
- 14: Fastener (screw) for door bin bracket
