6V Kids Ride On ATV 4-Wheeler

Safety Information

Please retain these instructions for future reference. This vehicle must be assembled by an adult who has read and understood the instructions in this manual. Keep packaging and bags away from children and dispose of all packaging before use. Always use common sense and safe practices when operating this vehicle.

California Proposition 65 Warning: This product contains or emits chemicals known in the State of California to cause cancer or birth defects or other reproductive harm.

General Safety Precautions

• For best performance, only use this vehicle on flat and hard surfaces.
• Age Range: 1.5 - 3 years old
• Weight Capacity: 44 lbs.

Hazard Warnings

• This product contains small parts. Keep children away during assembly. Ensure all packaging material and parts are removed from underneath the vehicle body.
• Never open the battery. Batteries contain lead and lead compounds (acids) that are toxic and corrosive, and known to the State of California to cause cancer and reproductive harm.
• Limbs, hair, and clothing can get caught in moving parts. Always wear shoes, keep limbs away from moving parts, and do not wear loose clothing while operating this vehicle.
• This vehicle does not have brakes or braking capability. Do not leave a child unattended during operation. Do not use this in a location that may require braking capability, as this could result in loss of control, which may cause serious injury or death.
• Use of this vehicle near streets, motor vehicles, steps, bodies of water, sloped surfaces, hills, wet areas, flammable vapors, in alleys, at night, or in the dark could result in an unexpected accident.
• Use of this vehicle in unsafe conditions such as snow, rain, loose dirt, mud, sand, or gravel may result in an unexpected accident such as tipping over, and could damage the electrical system or battery.
• Do not operate this vehicle in an unsafe manner. Examples include but are not limited to: pulling the vehicle with another vehicle, allowing more than one rider, pushing the user, or traveling at an unsafe speed.
• This product is intended for residential use only.

Battery Warnings

• Use of a battery or charger other than the supplied rechargeable battery and charger may cause a fire or explosion. Only use the supplied battery and charger.
• Use of the rechargeable battery and charger for any other product may result in overheating, fire, or explosion. Never use the supplied rechargeable battery and charger with another product.
• Explosive gases are created during charging. Charge the battery in a well-ventilated area. Do not charge the battery near heat or flammable materials.
• Contact between the positive and negative terminals may result in fire or explosion. Avoid direct contact between the terminals. Picking up the battery by the wires or charger can cause damage to the battery and may result in a fire. Always pick up the battery by its case or handles.
• Liquids on the battery may cause fire or electric shock. Always keep all liquids away from the battery and keep the battery dry. Contact or exposure to battery leakage (lead acid) may cause serious injury. If contact or exposure occurs, immediately call your physician. If the chemical is on the skin or in the eyes, flush with cool water for 15 minutes. If the chemical was swallowed, immediately give the person water or milk. Do not give water or milk if the patient is vomiting or has a decreased level of alertness. Do not induce vomiting.
• Battery posts, terminals, and related accessories contain lead and lead compounds (acid) – chemicals known to the State of California to cause cancer, reproductive harm, and are toxic and corrosive. Never open the battery.
• Tampering or modifying the electric circuit system may cause a shock, fire or explosion and permanently damage the system. Exposed wiring and circuitry in the charger may cause electric shock. Always keep the charger housing closed.

Specifications

Parts and Tools Required

Tools Required

• Plastic Wrench (Provided)
• Phillips Screwdriver

Hardware

• 1 Self-Tapping Screw (4 pcs)

Parts List

• A ATV BODY
• B HANDLEBARS
• C MOTOR
• D REAR AXLE
• E REAR SUPPORT
• F WHEEL COVER
• G WHEEL
• H FRONT BUMPER
• I FRONT AXLE
• J 6V CHARGER

Diagrams

Diagram shows an ON/OFF BUTTON located on the handlebar.Diagram shows a CHARGING PORT located at the rear of the seat.

Product Assembly

Estimated Assembly Time: Approximately 45 minutes (2 people recommended)

Step 1

Place the Part A ATV body on a flat, covered surface to prevent scratches. Locate the Part I front axle. Remove the pre-assembled hardware: two nuts, two washers, and two square tube covers.

Step 2

On the bottom of the Part A ATV body, place the square tube covers onto the square pipe. Insert the Part I front axle through the square pipe, then secure by replacing the hardware.

Step 3

Locate the Part D rear axle and remove the pre-assembled hardware, setting it aside. Note: Leave the bushings on the axle in place.

Step 4

Remove the pre-assembled hardware from the Part I front axle and set it aside. Locate the Part C motor and plug its adapter into the receiver at the back of the Part A ATV body. Push the Part D rear axle through the opening in the back of the ATV body and the Part C motor.

Step 5

Attach two Part G wheels to the Part D and I axles. Secure each wheel with the axle's respective hardware. Affix four Part F wheel covers to each wheel.

Step 6

Attach the Part E rear support to the Part A ATV body using four Part 1 self-tapping screws.

Step 7

Flip the ATV body upright so all four wheels touch the ground. Locate the Part B handlebars and remove the pre-assembled hardware. Insert the handlebars into the ATV body, then thread the handlebar shaft through the hole on the Part I front axle. Reattach the hardware to secure.

Step 8

Attach two Part H front bumpers to the front of the ATV.

Step 9

Locate the knob on the seat of the ATV body. Turn the knob counterclockwise to open the seat.

Step 10

Thread the handlebar's wire through the opening and into the recess under the seat.

Step 11

Connect the handlebar wire to the motor wire, then connect the power terminal as shown. Replace the seat.

User Instructions

Operation

After completing the initial charge, have the user sit on the designated seat. Locate the on/off switch on the handlebar. Press and hold the on/off switch to make the ride-on move forward; release the button to stop. This product has no braking capabilities.

Charging Instructions

Charging Procedure

• The charging connector is located at the rear of the seat.
• Insert the Part J charger into the charging port and plug the other end into a wall outlet.
• Charge the battery for 12 hours before initial use.
• When fully charged, unplug the Part J charger from the wall outlet and store it under the seat.

Caring for Your Ride-On

• Park the vehicle indoors or cover it with a tarp to protect it from wet weather.
• Do not leave the vehicle in the sun for long periods of time, as fading may occur. Store in shade or cover with a tarp.
• Do not wash the vehicle with a hose.
• Do not wash the vehicle with soap.
• Charge the battery at least once a month to prolong its life.

Troubleshooting

Compliance and Warnings

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This product may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Responsible party (contact for FCC matters only): Quality Control Dept. 15101 Red Hill Ave. Tustin, CA 92780

California Proposition 65 Warning

WARNING: Battery posts, terminals, and related accessories can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm, and are toxic and corrosive. Wash hands after handling. For more information go to www.P65Warnings.ca.gov.

Support and Warranty Information

Help Center

Question about your product? Visit help.bestchoiceproducts.com. Support options include Chat Support, Product Inquiry, Orders FAQ, Product Assembly, and Returns & Refunds.

Product Warranty Information

All items can be returned for any reason within 60 days of receipt for a full refund, provided the item is returned in its original product packaging with all accessories from the original shipment included. All returned items will receive a full refund back to the original payment method and will not be charged a restocking fee.

All returns require an RA (Return Authorization) number, provided by a Best Choice Products Customer Service Representative when the return request is submitted. Items received without an RA may not be accepted or may increase processing time. Once an item is received by Best Choice Products, refunds or replacements will be processed within 5 business days.

All returns must be shipped back to the Best Choice Products Return Center at the customer's expense. If the reason for return is an error by Best Choice Products, they will provide a pre-paid shipping label via email. Boxes for return shipping will not be provided; customers are responsible for using original boxes or purchasing new ones.

Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are not considered undamaged until they are received by Best Choice Products and verified as such. All damages to items are the customer's responsibility until the item has been received by and acknowledged by Best Choice Products as undamaged.

Manufacturer Disclaimer

Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.