Creality Laser Module Quick Start Guide

Introduction

Dear Consumers:

Thank you for choosing Creality products. For the best experience, please read this quick start guide carefully before operating the machine. Our teams are always ready to provide you with the best services. If you encounter any problems during use, please contact us via the phone number or email address provided at the end of this guide.

For a better experience, you can also learn how to use the engraving machine in the following ways:

• View the accompanied instructions and videos on the TF card.
• Visit the official website www.creality.com for relevant software/hardware information, contact details, operation, and maintenance instructions.

Firmware Upgrade

Download the latest firmware from https://www.creality.com/pages/download-cr-laser-falcon-laser-engraver. Save the '.bin' file to the root directory of the TF card, backing up any other files you need from the TF card and then deleting them, leaving only the firmware file on the card. Insert the TF card into the machine when it's powered off, then turn on the machine. It will update automatically. A buzzer will sound during the update process. When the update is completed, the sound will stop. Do not power off during the update process.

Product Parameters

Parts List

10W Laser Module Wireframe:

• Protective goggles
• Protective lens
• Thumb screw

1.6W, 5W Laser Module Wireframes:

• Protective goggles
• Thumb screw
• Activated carbon absorbing cotton
• Fixed focus bar

Control Box Components:

• Microswitch
• Switch
• TF card slot
• Type-C interface
• Power interface

Included Parts:

1. Laser module*1
2. Laser module fixing plate*1
3. Control box kit*1
4. Type-C data cable*1
5. Hexagon socket head screw*1
6. Black cable management belt*5
7. Quick start guide*1
8. Allen wrench*1
9. Multi-level fixed focus bar*1 (Only for 10W laser module)
10. Black nylon cable tie*3
11. TF card & card reader*1
12. Cleaning cloth*1
13. Protective goggles*1
14. Power adapter*1
15. Power cord*1

Assembly Directions (Example: Ender-3 V2)

1. Pull out the X-axis motor cable, Y-axis motor cable, X-axis limit switch cable, and Y-axis limit switch cable from the printer. (For Ender-3 v2, Ender-3 v2 neo, Ender-3 max neo, remove the Y-axis limit switch protective cover before wiring).
2. Connect the control box to the printer, paying attention to the "X" and "Y" labels on the cables. The "Z" corresponds to the laser module cable.
3. Adjust the height of the Z axis.
4. Install the laser module fixing plate (it should be vertical) and lock the screw.
5. Install the laser module, use two thumbscrews to lock it, and plug in the laser module cable with "Z".
6. Use cable ties and cable management belts to arrange the cables.

Notes:

• For Ender-3 s1, Ender-3 s1 pro, Ender-3 s1 plus, the Y-axis motor cable needs to be routed to the side to prevent it from being pulled. Before installing the laser module fixing plate, remove the extruder (loosen four screws).
• For Ender-3 neo, Ender-3 v2 neo, and Ender-3 max neo, tilt the laser module fixing plate slightly to install it in the suitable position.
• For some machines, the Z-axis may drop during engraving. Lock the Z-axis by turning on the printer or by other means.
• All cables must be plugged and unplugged when the machine is powered off.

Software Installation and Usage Guide

The machine can be controlled via a Type-C data cable for online operation or via a TF card for offline operation (only LightBurn can generate engraving files). For detailed software tutorials, refer to the information on the TF card.

Preparation

Before starting to engrave, complete the following preparations:

1. Read the "Safety Precautions" again carefully.
2. Ensure the protective lens of the laser module is clean and adjust the focal length correctly.

For 1.6W, 5W Laser Module: The fixed focus bar should naturally contact the surface of the material when vertical. Lock it with the two hand screws on the right. Turn the fixed focus bar clockwise until it is attracted by the magnet. Finally, plug in the laser module cord.

For 10W Laser Module: Place the multi-level fixed focus bar between the laser module and the material. Follow the tips on the focus bar to align the bottom of the laser module with the corresponding surface of the multi-level fixed focus bar. Lock it with the two hand screws on the right. For example, when engraving or cutting 2mm basswood or other material.

Modify GRBL Configuration Parameters:

After successfully installing LightBurn software and adding the printer, if your printer's X and Y print size is not 220mm, modify the configuration parameters $130 and $131 in the console. For details, refer to the "User manual for LightBurn" file on the TF card.

Online Operation

Connect the control box and use the software to operate the machine in real-time through the Type-C cable. For details, please refer to the information in the TF card. Note: When operating via Type-C, do not insert the TF card and do not press the micro switch on the control box.

Offline Working

1. First, generate the engraving file (.gcode/.gc/.g/.nc/.ngc) through LightBurn software and save it to the root directory of the TF card (the machine defaults to reading the latest engraving file in the first-level directory. It is recommended to delete other engraving files in the first-level directory). Insert the TF card into the machine before powering on. Then, use the provided power adapter and power cord to connect the machine, and finally turn on the red power switch on the right side of the control box.

After the power is turned on, the machine emits three beeps ("di...di...di"), enters standby mode after initialization, and the indicator light turns into a flashing light.

2. Press the microswitch. The machine will enter preview mode from standby mode. The laser head will emit a weak laser and move repeatedly around the largest X, Y borders of the processed engraving/cutting area, with the indicator light on. At this time, adjust the material to a suitable position.

In preview mode, press the microswitch again to enter engraving mode. The laser head will emit the corresponding laser power, and the machine will start engraving with the indicator light on.

If you need to pause engraving, press and hold the microswitch for 3 seconds. The machine will emit one "beep" and return to the home position. After reset completion, it will emit two "beeps" and enter standby mode, with the indicator light flashing.

If you need to cancel engraving, press and hold the microswitch for 3 seconds. The machine will emit one "beep" and return to the home position. After reset completion, it will emit two "beeps" and enter standby mode, with the indicator light flashing.

3. After engraving is completed, the machine will emit three "beeps", return to the home position, emit two "beeps" upon completion of reset, and enter standby mode with the indicator light flashing.

Indicator Status Description

1. Indicator Light Off: The machine is powered off or has a power abnormality.
2. Slow Flashing Light: The machine is in standby mode. Press the microswitch to enter preview or engraving mode.
3. Fast Light Flashes: The machine is in upgrade mode. The buzzer beeps quickly, and it will automatically enter standby mode after the upgrade is completed.
4. Light Always On: The machine is in preview or engraving mode. The laser head is working; pay attention to safety.

Offline Working Flowchart

Start

• Disconnect the power.
• Pull out the X/Y motor wire and limit switch wire.
• Insert the TF card into the control box card slot.
• Power on and turn on the switch.
• Wait for initialization completion.
• Press the micro switch to enter preview mode.
• Press the micro switch again to engrave.
• Decision: Press microswitch? (Yes/No)
• If Yes:
• Long Press: Decision: In pausing mode? (Yes/No)
• If Yes: Continue engraving.
• If No: Pause engraving.
• If No: Short Press.
• Decision: In pausing mode? (Yes/No)
• If Yes: Continue engraving.
• If No: Pause engraving.
• Stop engraving.

Preparation Steps:

• Install the laser module fixing plate.
• Install the laser module.
• Plug in the Laser Module wire.
• Place metal protective plates and engraving materials.
• Adjust focus of laser module.
• Modify GRBL configuration parameters and restart the control box.
• Prepare engraving file and save it to TF card.
• End

Online Working Flowchart

Start

• Disconnect the power.
• Pull out the X/Y motor wire and limit switch wire.
• Connect the control box to the printer.
• Connect power and turn on the switch.
• Select the corresponding COM port in the software and connect the control box.
• Modify GRBL configuration parameters and restart the control box.
• Import pictures into the software.
• Setting parameters.
• Frame preview.
• Start engraving.
• End

Preparation Steps:

• Install the laser module fixing plate.
• Install the laser module.
• Plug in the Laser Module wire.
• Place metal protective plates and engraving materials.
• Adjust focus of laser module.
• Use a Type-C data cable to connect the computer and the control box.

Product Warranty Card

Before returning the product and filling in a warranty, please contact the after-sale service representative for the after-sale process. Please fill out this card and send it back with the machine.

Repair | Change | Return

Customer Name:

Address:

Telephone:

Malfunction and Damage Description or Return and Change Reasons/Suggestions:

Machine Serial Number:

Order Number:

Repair Records:

Channel: Platform [ ] Offline [ ]

Date of Purchase: Day [ ] Mon. [ ] Year [ ]

Note: Clients need to fill in basic information and return reasons. Repair records will be kept by technicians.

Company Information

Shenzhen Creality 3D Technology Co., Ltd.

Address: 18F, JinXiuHongDu Building, Meilong Blvd., Longhua Dist., Shenzhen, China 518131

Official Website: www.creality.com

Tel: +86 755-8523 4565

E-mail: info@creality.com, cs@creality.com

3D Printing Evangelists

With the spirit of evangelists, we want to share the convenience of technology with everyone.