World leading CCTV Tester, Cable tester, Fiber tester original manufacturer
User Manual for WANLUTECH models including: CT-66 Multi Function Wire Tracker, CT-66, Multi Function Wire Tracker, Function Wire Tracker, Wire Tracker, Tracker
WANLUTECH Cable Finder,Proster Wire Tracker LCD Network Cable Tester RJ11 RJ45 Line Finder Multifunction Wire Tracer for Cable Collation Continuity Checking Telephone Line Test(CT-66) : Tools & Home Improvement
WANLUTECH Network Cable Tester,Digital Cable Tracer Wire Tracker RJ11 RJ45 Cable Toner Line Finder Ethernet LAN Cable Tester Wire Tracer for Cable Collation Continuity Checking Telephone Line Test: Industrial & Scientific
CT-66 User Guide (PDF) WANLUTECH WANLUTECH Network,Cable,Tester,Digital,Cable,Tracer,Wire,Tracker,RJ11,RJ45,Cable,Toner,Line,Finder,Ethernet,LAN,Cable,Tester,Wire,Tracer,for,Cable,Collation,Continuity,Checking,Telephone,Line,Test,CT-66,B0BYD55315,B09TS9X6ZG,B0BXS18SVR
File Info : application/pdf, 15 Pages, 1.01MB
DocumentDocumentMulti-function Wire Tracker User Manual Model: CT-66 Thank you for purchasing WANLUTECH Wire Tracker. Please read the manual before using the Wire Tracker and use properly. For using the Wire Tracker safely, please first read theSafety Informationcarefully in the manual. The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period. Product without S/N label will be charged for repair service. If there is any question or problem while using the Wire Tracker, or damages occurred on the product, please contact our After-sales service department (sales@testerpro.com.cn) The following data is for reference only and no additional notice will be given if there are any changes in the data. Content 1. Safety information ..................................................................................................... 2 2. Feature ....................................................................................................................... 3 3. Packing list .................................................................................................................3 4. Interface and Function Introduction .......................................................................... 4 5. The instruction of product application .....................................................................7 5.1 Cable tracer ..................................................................................................... 7 5.2 UTP detection ................................................................................................... 9 5.2.1 Sequence and pair line continuity detection ........................................... 9 5.2.2 Network cable port continuity detection .................................................9 5.2.3 Short circuit test .................................................................................... 11 5.2.4 Continuity detection in the state of connected switches ....................... 11 5.3 PD powered detected ...................................................................................... 12 5.4 Other features ..................................................................................................12 6. Specifications ...........................................................................................................13 www.cctvtester.com 1 After-sales service department(sales@testerpro.com.cn) 1. Safety information The wire tracker is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc. To prevent the functional decline or failure, the product should not be sprinkled or damped. The exposed part of the wire tracer should not be touched by the dust and liquid. Don't use the wire tracer where the temperature is high. Please don't use this instrument to detect power lines (such as 220V power lines), otherwise it may damage the instrument or involve personal safety. During transportation and use, it is highly recommended to avoid the violent collision and vibration of the tester, lest damaging components and causing failure. The wire tracker should not be used in the environment with the flammable gas. Do not disassemble the instrument since no component inside can be repaired by the user. If the disassembly is necessary indeed, please contact with the technician of our company. The instrument should not be used under the environment with strong electromagnetic interference www.cctvtester.com 2 After-sales service department(sales@testerpro.com.cn) 2. Feature Secondary code digital mode, decisively rejects noise and false signals, locate cables quickly and easily. Cable tracer and UTP cable test in the same interface. Identify cable type:100M/1000M, straight/cross/other. UTP/STP/RJ45/RJ11 cable scan and continuity testing. Identify the status in the working telephone line: standby, ringing and off-hook Quickly detect the near-end, mid-end and far-end fault point of RJ45 cable plug UTP port support max 60V withstand voltage, the wire can be traced directly in connection with PoE switch. Shielded cable and shielding layer continuity test PD powered detection: detect whether the power output of the POE switch is normal, and detect the pins used for power supply. Support silent mode Two bright LED lights for working in the dark 3. Packing list 1) Wire tracker emitter 2) Wire receiver 3) RJ45 cable 4) RJ11 cable 5) BNC alligator clip 6) User manual www.cctvtester.com 3 After-sales service department(sales@testerpro.com.cn) 4. Interface and Function Introduction 1) Emitter Interfaces and functions: 1 Telephone status indicator 2 Functions switch: SCAN/UTP, OFF, UTP cable test 3 UTP cable sequence/ continuity indicators, G is shielded cable 4 UTP cable type indicator: straight /cross /other 5 100M /1000M indicator 6 Cable tracer mode indicator: Green-normal mode, red-shielded mode 7 SET: Switch function shielded or unshielded in cable tracer mode and "local / remote / switch" in UTP cable test mode 8 Battery indicator 9 SWITCH continuity indicator 10 LOCAL/ Remote end continuity indicator www.cctvtester.com 4 After-sales service department(sales@testerpro.com.cn) Top interface Left interface 11 BNC interface 12 UTP/ Scan port 13 RJ11 port Note: Please use telephone status detection in the OFF status. The indicator light off / on / flashing correspond to telephone status standby / ringing / off-hook. 2) Cable tracer (Receiver) Interfaces and functions 1 LED light www.cctvtester.com 5 After-sales service department(sales@testerpro.com.cn) 2 Power Indicator 3 UTP cable sequence / signal strength indicator 4 Shielded layer continuity indicator 5 Earphone jack 6 UTP cable test port 7 LED light switch 8 100M /1000M indicator 9 Switch / Sensitivity knob 10 MUTE button (long press to silent mode, short press to port connectivity detection) 11 UTP cable type indicator: straight /cross /other 12 Port continuity detection indicator (ON indicates local end cable connectivity function, OFF indicates cable sequence function) Bottom interface 13 PD Powered test port (detect whether the power output of the PoE switch pins is normal.) Note: Receiver port continuity detection only supports the local end, does not support the remote end. Emitter can support the near end, middle end and far end port detection. www.cctvtester.com 6 After-sales service department(sales@testerpro.com.cn) 5. The instruction of product application 5.1 Cable tracer Connect the network cable into the emitter's RJ45 port, connect BNC cable or RJ11 telephone line to the emitter's BNC or RJ11 port. If no connector cable, can use alligator clips to clip the bare copper wire. (1) Adjust the switch of emitter to the "Scan/UTP" mode, press "SET" key to switch to UTP/STP mode. The green light of the "UTP/STP" indicator means normal mode, while the red light is shielded mode. Turn on the wire receiver at the same time to trace the wire. (2) Rotating the knob of receiver to adjust the sensitivity. When the cables are very close, can adjust to the small sensitivity to find the cable. www.cctvtester.com 7 After-sales service department(sales@testerpro.com.cn) Long press the "MUTE" key for silent mode. In this mode, the signal strength indicator l ight is used to trace the wire. When received the strongest signal, the eight indicator lights are on. Press "MUTE" again to exit MUTE mode. (3) Quickly verify the tracking result (only for RJ45 port). After found the cable, connect the network cable to wire receiver "UTP" port for pair line detection. For example, When the "Straight/Cross/Other" lights up, indicates the verification of the matching cable. The indicator also shows the type of the cable. The 1-8 and G indicators show the detection of line sequence by default, and the order in which the indicator lights up is the sequence of the line. When connected the cable, the receiver indicator the cable status by sound, the "di" sound is connected pair lines, the "du" sound is short circuit pair lines, all indicator lights of short circuit pairs are on at the same time. (4) Port continuity and short circuit detection: Press "MUTE" button, when the indicator light of port is on, the 1-8 and G indicator lights will show the continuity of the line of the RJ45 cable connector or within 1 meter from RJ45 cable connector. As shown on the right, If the light is on, it means it is connected and vice versa. One end of network cable connected to the receiver, the other end is not connected to the emitter, press "Mute", the "Port" light on, can test the continuity and short circuit of network cable. Application: Connect one end of network cable to Switch, and the other end connect to RJ45 port of emitter, press "SET" key to switch to the "SWITCH" mode, If the 1236 indicators light on, that is 100M switch, If 12345678 indicators light on, that is 1000M switch. (5) The UTP port of emitter and receiver can max 60V withstand voltage, the wire can be traced directly in connection with PoE switch www.cctvtester.com 8 After-sales service department(sales@testerpro.com.cn) 5.2 UTP detection 5.2.1 Sequence and pair line continuity detection Step 1: Connect the network cable or telephone cable to the RJ45 port of emitter, and the other end connect to the UTP interface of receiver. (The wire receiver needs to be turned on) Step 2: Switch the wire tracker emitter to UTP mode, the 1-8 and G indicators will indicate the sequence of cable, 100M and 1000M indicator will indicate whether the cable is 100M or 1000M network, the cable receiver also can see the sequence. Quickly determine the cable whether is normal through wire tracer emitter or wire receiver, if indicate Direct/ Cross, the cable is normal. After the 8 indicators flashed, the wire receiver will beep to indicate the type of network cable. One sound is a straight cable, double sound is cross cable, and triple sound is another or wrong cable. 5.2.2 Network cable port continuity detection In the UTP mode, press "SET" key to switch "LOCAL" mode. Local port continuity detection: when the "LOCAL" indicator is on, connect the other end of network cable to wire receiver "UTP" port or disconnect the UTP port, the 1-8 and G indicators indicate the continuity status of network cable port or within 1 meter of network port which connected wire tracker emitter. As shown in the picture below, the 1st core of network cable port on the side of emitter is disconnected, the 1st indicator is off, it means 1st core of port is disconnected. www.cctvtester.com 9 After-sales service department(sales@testerpro.com.cn) Under UTP mode, press "SET" key to switch to the "REMOTE" function Remote end continuity detection: The "REMOTE" indicator is on, connect the other end of the cable to the UTP port of Receiver. 1-8, G indicator indicates the continuity of the cable port which connected to the Remote end (Receiver) or the cable within 1 meter from the port. As shown in the picture below, the 5th core of the cable port on the side of the cable tracer (receiver) is disconnected, and the 5th indicator in the 1-8 indicators is off, indicating that the 5th core of the port is disconnected and the other cores are connected. The detection: www.cctvtester.com After-sales service department(sales@testerpro.com.cn) mid-end of cable continuity If the cable sequence detects that the 10 cores of the cable are disconnected, and the local / remote cores are detected to be connected, indicating that the break point of the cable is in the middle position away from the ports on both sides. 5.2.3 Short circuit test 1) Not connect receiver end 6 and 7 cores are short circuit Emitter mode: The indicator lights of the short circuit pairs are flashing Switch mode: The indicator lights of the short-circuit pairs are on. 2) Connect receiver end Sequence mode: The indicator lights of the short-circuit pair are on at the same time. Emitter and Remote mode: The indicator lights of the short circuit pairs are flashing. Note: Under the port mode of receiver, the indicator lights of the short circuit pairs are flashing. 5.2.4 Continuity detection in the state of connected switches Under UTP mode, press "SET" key to switch to the "SWITCH" function. When connected to a switch, 1-8, G indicator indicates the continuity of the cable, lights on means connected, lights off means disconnected (The 100M switch is 1236 line connected, the 1000M switch is 1-8 lines connected). In this mode, connect one end of cable to the RJ45 port of emitter, and the other end of cable disconnect to the switch, also can detect the short circuit status of network cable, the indicator light will be on if short circuit. Switch www.cctvtester.com 11 After-sales service department(sales@testerpro.com.cn) 5.3 PD powered detected PoE switch or PSE power supply device connected to the "PD" port of the cable tracer, if the indicator light is on, it means PoE voltage output working normal. There are 4 indicator lights of the "PD" port, when testing the pins used of PoE switch for power supply, if 1236 indicator light is ON, it means PoE switch supply power through Pin 1236. If 4578 indicator light is ON, it means PoE switch supply power through pins 4578. If 1236 and 4578 indicator lights are ON, it means device power supply through pins 1236 and 4578. Application: Checking the pins used of PoE switch or other device for power supply, to avoid cause cannot supply power or camera and other device damaged. 1236 pins supply power 4578 pins supply power 1236 and 4578 pins supply power 5.4 Other features Line DC level and positive / negative polarity testing Turn off the emitter, the red and black wire clip of BNC cable connect to the telephone line or battery, the other end connect to BNC port. (Note: If the telephone cable with welled RJ45 connectors, directly connect telephone cable to RJ11 port) If the indicator light is in green, that means the red wire clip is positive, and the black clip is negative, if the indicator light is in red, that means the black wire clip is positive, and the red wire clip is negative. The level is higher, the indicator light is brighter, the level is lower, the indicator light is darker. www.cctvtester.com 12 After-sales service department(sales@testerpro.com.cn) 6. Specifications Item Wire Tracker Emit signal Digital signal(rejects noise and false signals) Cable type RJ45 Twisted pair, RJ11 telephone line, BNC cable etc. UTP cable test Continuity test of RJ45 cable connectors The digital "1-8" for cable sequence shielded cable and shielding layer continuity indicator, check cable type indicator: straight/cross/other, 100M/1000M network cable test, and near-end, mid-end, far-end continuity testing, UTP cable short circuit test Detect the continuity of the pins on both sides of network cable and short circuits PD (powered) test PoE switch power supplying status test and check the pins used for power supply LED lamp Silent mode Audio output Short press On /Off LED light Long press key "Mute" to switch silent mode, find cable through indicator Support external audio output Power supply External power supply Two AA batteries General Working Temperature -10---+50 Working Humidity 30%-90% Dimension Emitter Dimension 152mm x 62mm x 27mm /0.12KG Receiver Dimension 218mm x 48mm x 32mm /0.1KG WARM TIP: 1. The above data is for reference only, and you will not be notified in advance of any changes in the data. 2. For more detailed technical inquiries, please feel free to contact our After-sales service department (sales@testerpro.com.cn) www.cctvtester.com 13 After-sales service department(sales@testerpro.com.cn)