Philips Radii Ultra Efficient
Model Number: 9290040674
This manual is available in multiple languages:
- English (User manual)
- German (Benutzerhandbuch)
- French (Notice d'emploi)
- Spanish (Manual de usuario)
- Portuguese (Manual do usuário)
- Italian (Manuale d'uso)
- Dutch (Gebruiksaanwijzing)
What's Included and Required
Included in the Box:
- ? Manual A
- ? Manual B
- Lamp components (labeled A and B in diagrams)
Excluded (Tools Required):
- ? Drill
- ✏️ Pencil
- ? Screwdriver
- ? Screws and wall plugs (for mounting)
Product Features and Specifications
IP Rating: IP44 ? (Protected against solid objects >1mm and water jets from any direction)
Safety Class: III (Low voltage)
Motion Sensor:
- Detection Range: 0m to 8m
- Detection Angle: 120° ?
Light Source: LED ?
Control Modes: Indicated by 'A' on the product.
Battery Indicator: Visual representation of battery charge level.
Operation and Settings
Step 1: Accessing the Lamp Head
To access internal components, gently twist the top part of the lamp counter-clockwise (1) and lift it upwards (2).
Refer to diagram on page 3.Step 2: Basic Control Switch Settings
Inside the lamp head, locate the control switch. It has three positions:
- OFF: The lamp will not turn on.
- AUTO: The lamp operates automatically. It turns ON when motion is detected and turns OFF when no motion is detected (in darkness).
- ON: The lamp will remain on continuously.
The diagrams illustrate the switch positions and the resulting light behavior:
| Switch Position | Light State (No Motion) | Light State (Motion Detected) |
|---|---|---|
| OFF | ? OFF | ? OFF |
| AUTO | ? OFF | ? ON |
| ON | ? ON | ? ON |
Installation
Step 3: Prepare the Mounting Base
The lamp post has a base designed for mounting. Ensure the surface is stable and level.
Refer to diagram on page 4.Step 4A: Mounting to a Hard Surface (e.g., Concrete)
If mounting to a hard surface like concrete:
- Mark the desired position for the base.
- Drill holes using a drill bit of ⌀6mm ?.
- Insert appropriate wall plugs into the drilled holes.
- Position the lamp base over the holes and secure it with screws.
Step 5A: Attaching the Lamp Post to the Base
Insert the bottom of the lamp post into the prepared base (1) and secure it using the provided screws (2).
Refer to diagrams on page 4.Step 4B/5B: Assembling the Lamp Post
If the lamp post comes in multiple sections, assemble them by connecting the parts as shown in the diagrams. Ensure all connections are secure.
Refer to diagrams on page 5.Step 6A: Solar Charging and Orientation
The lamp is solar-powered. Ensure the solar panel at the top is exposed to direct sunlight for optimal charging.
The diagrams illustrate:
- Battery charging status: From low ? to full ?.
- Light output based on direction: The intensity of the light may vary depending on the direction it is facing relative to the sun's path (N, S, E, W). For best performance, orient the lamp to maximize sun exposure.
Step 6B: Installing into the Ground
If installing directly into soil or soft ground, push the stake at the bottom of the lamp post firmly into the ground until it is stable.
Refer to diagram on page 6.Step 7: Advanced Motion Sensor Modes
The lamp offers different operating modes (A, B, C, X) when the control switch is set to AUTO. These modes customize the light's behavior in response to motion and ambient light conditions.
- Mode A: When motion is detected ?♂️, the light turns ON ?. When no motion is detected, the light turns OFF ? OFF.
- Mode B: When motion is detected ?♂️, the light turns ON ?. When no motion is detected, the light remains dimly lit ? Dim.
- Mode C: When motion is detected ?♂️, the light turns ON ?. When no motion is detected, the light turns OFF ? OFF.
- Mode X: When motion is detected ?♂️, the light turns ON ?. When no motion is detected, the light turns OFF ? OFF.
The diagrams use signal icons ? to represent motion detection and show the corresponding light output for each mode.
Refer to diagrams on page 6.Battery Replacement
The lamp is powered by a rechargeable battery. If performance degrades, the battery may need replacement.
Step 1: Open the Battery Compartment
To access the battery, twist the top cover counter-clockwise (1) and lift it upwards (2).
Refer to diagram on page 7.Step 2: Replace the Battery
The lamp uses one 18650 3.7V Li-ion 1800mAh battery.
- Carefully remove the old battery.
- Insert the new battery, ensuring correct polarity (+ and -) as indicated.
- Dispose of the old battery responsibly.
Step 3: Close the Battery Compartment
Place the cover back onto the lamp and twist it clockwise (1) to secure it (2).
Refer to diagram on page 7.Company Information
Signify Commercial UK Limited
Unit 3, Guildford Business Park,
Guildford, Surrey, GU2 8XG, UK
Signify
I.B.R.S. / C.C.R.I. Numéro 10461
5600 VB Eindhoven,
the Netherlands
Customer Service: ? 00800-74454775
Website: www.philips.com/lighting
© 2023 Signify Holding
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
Product Code: 3241 661 00301
