User Manual for B PLUS models including: B PLUS, 5 Bit, 8 Bit, 10 Bit, System, Reader, Writer, T712802Ge
[Planning the System]. - Do not exceed the specifications for supply voltage, conditions of use, etc. as indicated in this manual.
3 - Reader/Writer Z6-01-U "B&PLUS ID System / 5,8,10 bit System" is a RFID System by electromagnetic induction method, reading and writing of data.
Issue : March.16, 2021 No. T712802Ge G 5/8/10 Bit System Instruction Manual for Reader/Writer Type code Z6-01-UUSB interface 5bit Left: This is the appearance provided until around April 2021. (Old) Right: This is the appearance provided after around April 2021. (New) The shape is different, but the function is the same. Safety Considerations (Please read before use) Before using Z6-01, read this manual carefully and operate properly, paying attention to the safety aspects. [Planning the System] - Do not exceed the specifications for supply voltage, conditions of use, etc. as indicated in this manual. This may cause severe overheating [Handling the System] - Supply the power only described in the specification. - Do not dismantle or modify the devices. This could cause malfunction or overheating. - Dispose the device as the industrial waste. Reader/Writer Z6-01-U Contents 1 Description 1. 1 Description 3 1. 2 System configuration 3 1. 3 Dimension and Specification. 4 1. 4 Applicable RFID chip 4 2 Installation of driver and IDRWUSB 2. 1 Attention before installation 5 2. 2 Installation of driver 5 2. 3 Installation of IDRWUSB 6 3 How to use IDRWUSB 3. 1 Setting of the COM port 6 3. 2 Select the bit number 6 3. 3 For IDRWUSB connection 6 3. 4 Reading of data 7 3. 3 Writing of data 7 - 2 - Reader/Writer Z6-01-U . Description . 1 Description "B&PLUS ID System / 5,8,10 bit System" is a RFID System by electromagnetic induction method, reading and writing of data. By Z6-01-U is connected by or USB to the PC, you are using an application (IDRWUSB) , it can be done easily from the personal computer, the editing and data writing and data reading of the Data carrier. 1. 2 System configuration Data carrier Reader/Writer Z6-01-U PC Applicable OS see below The data storage media. Media that reads and writes data to the Data carrier. Interface -SerialUSB Data carrier Reader/Writer Driver Application PC The data storage media. Media that reads and writes data to the Data carrier. Driver to recognize the Reader/Writer to the PC. Software for performing data editing. In the application, edit the data and Instructions data communication. Applicable OSWindwos 2000 / XP / Vista / 7 / 8 / 10 About Driver and Application software Product documentation and software, it can be download from our web site. URLhttp://www.b-plus-kk.jp/download.html The ID and password are as below. ID:user , Passwordwirelessbplus Driver and application depends on the connection method and the ID reader-writer. Type code Connection Application Driver COM port Z6-01-U USB IDRWUSB-xxx Need Selected application is automatically Driver that you want to install different by Windows. Windows2000 CDM20600.exe OthersCDM20828_Setup.exe - 3 - Reader/Writer Z6-01-U 1. 3 Dimension and Specification. 4 32 1 1V bus 2D 3D + 4 GND 20.0 72.0 2200..00 7722..00 16.0 67.0 112200.0.0 119.0 4 32 1 1V bus Z6-01-UOld 2D 3D + Z6-01-UNew 4 GND Type code Z6-01-UOld Z6-01-UNew USB Applicable Data carrier Z1 series Carrier frequency 13.56MHz Interface USB Supply voltage 3.3V Max.190mA (Supply from USB ) Operating temperature / humidity 0 +50 / 20 80not to be frozen Storage temperature / humidity -10 +70 / 10 90not to be frozen Material ABS Body: ABS Cover: Silicon rubber Weight 90 116g Radio standards law (Japan) This machine has built-in high-frequency utilization equipment which acquired model designation (Ministry of Internal Affairs and Communications designated BC-09004). Left: This is the appearance provided until around April 2021. (Old) Right: This is the appearance provided after around April 2021. (New) The shape is different, but the function is the same. 1.4.Applicable RFID chip This unit corresponds to the Chip Maker Capacity communication protocol of the ID MB89R118 Fujitsu 2000byte(FRAM) chip on the right table. When using other than our ID tag (Z1 series), please confirm when using, as the communication dis- I-CODE SLI,SLIX Tag-it HF-I plus my-d(SRF55V02P) my-d(SRF55V10P) Tag-it HF-I standard NXP TI Infineon Infineon TI 112byte 256byte 224byte 992byte 32byte tance, the processing time and the Tag-it HF-I pro TI 32byte communication quality depend on the characteristics of the ID chip It is a registered trademark of I-CODE SLI, SLIX is NXP semiconductor FRAM is Ramtron InternationalTag-it is Texas Instruments Incorporatedmy-d is Infineon Technologies. and the ID reader / writer - 4 - Reader/Writer Z6-01-U 2. Installation of driver or IDRW 2. 1 Attention before installation Please start the installation from quit other applications. Depending on the version of windows,the different installation methods. The driver is intended to be treated as a COM port USB. 2. 2 Installation of driver Starting the Installation You are using Windows2000, please double-click the "CDM20600.exe". Errand, please double-click on the "CDM20828_Setup.exe" version of the other. Decompression of files ClickExtract Execution of installation Click (N) Finished Click - 5 - Reader/Writer Z6-01-U For drivers of this product This product uses USB interface IC by FTDI. The driver "VCP(Virtual COM port)" is also possible at the following Web sites by FTDI, be asked to download the latest version. http://www.ftdichip.com/ 2. 3 Installation of IDRWUSB After selecting "DRWUSB" folder, then transfer by drag and drop to the location of any of the personal computer, it becomes the installation is complete. 3. How to use IDRWUSB 3. 1 Setting of the COM port Please select the port Reader/Writer is connected. Appropriate port number in the case of the Z6-01-U is the number in the "port(LPT and COM) " of Device Manager of Windows, is listed as "USB Serial Port". 3.2Select the bit number Select 5 bits, 8 bits or 10 bits. In this manual, it is explained when 8 bit is selected. 3.3For IDRWUSB connection The setting of the COM port is done application is automatic. When the configuration is properly completed, you will see configuration information. - 6 - Reader/Writer Z6-01-U 3. 4 Reading of data After is opposed to Active surface with the Data carrier, you click the "READ" , please click the "START" . Data read from the Data carrier is displayed, "Finished" is displayed. 3. 5 Writing of data After is opposed to Active surface with the Data carrier, Click the "WRITE" , select "MODE" , input the data to "DATA" and then click the "START" . bit(Binary), decimal, HEX(hexadecimal) will be linked when you enter in any. Data is written to the Data carrier, "Finished" is displayed. - 7 - Application software change history Date File 2015.04.30 IDRWUSB_V300 2015.07.24 IDRWUSB_V320 2016.04.18 IDRWUSB_V400 Contents It corresponds to 10 bits. Release of USB application. Cottrdponds to Tag-it HF-Istandard,plus,pro. "10bit" is added in the operation screen. Corresponds to 5 bits Wireless Power Supply by Mail b-plus-usa@b-plus-kk.com Web http://www.b-plus-kk.com * Contents is subject to change without notice.Adobe PDF Library 10.0.1 Adobe InDesign CS6 (Windows)