Oster BVSTEM6601 Series Automatic Espresso, Cappuccino & Latte Maker

Important Safeguards

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

1. Read all instructions before using the appliance.
2. Check if the voltage indicated on the appliance corresponds to the local mains voltage before connecting the appliance.
3. Do NOT touch hot surfaces. Use handles or knobs.
4. To protect against electric shock, DO NOT immerse cord, plug, or appliance in water or other liquids.
5. Press the switch located on the side of the unit to the off position "O" and unplug unit from electrical outlet when not in use and before cleaning. Allow it to cool before putting on or taking off parts and before cleaning it.
6. DO NOT operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest Authorized Oster Appliance Service Center for examination, repair or electrical or mechanical adjustment.
7. The use of accessory attachments not recommended for Oster® products may result in fire, electric shock or injury to persons.
8. DO NOT use outdoors or for commercial purposes.
9. DO NOT let cord hang over edge of table or countertop or touch hot surfaces.
10. DO NOT place this appliance on or near a hot gas or electric burner or in a heated oven.
11. To disconnect, turn any control to the off position “O” then remove plug from wall outlet.
12. DO NOT use appliance for anything other than its intended use.
13. Use on a hard, flat level surface only, to avoid interruption of airflow underneath the appliance.
14. Always be sure to place the water reservoir tightly back in the unit with its lid closed and fill with water above the minimum before turning appliance on.
15. DO NOT remove the porta-filter while brewing coffee. Please make sure the three lights are on before you remove the porta-filter to make additional coffee. Caution should also be taken while removing the porta-filter since the metal parts will be hot. Please make sure to hold it by the handle and to use the filter retention clip to dispose the grounds. Caution should be taken when moving unit with hot liquids.
16. DO NOT remove the water reservoir until unit is turned off.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they DO NOT play with the appliance.
18. Close supervision is necessary when any appliance is used by or near children, or incapacitated individuals.
19. This appliance is not intended to be operated by means of an external timer or separate remote-control system.
20. This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments, farm houses, by clients in hotels, motels and other residential type environments, bed and breakfast type environments.

This unit is for household use only.

Save These Instructions

Caution: Pressure

In order to avoid possible burns to body parts and/or other injury from hot steam and water or damages to the unit, never remove the water reservoir or the porta-filter while your Oster® espresso, cappuccino and latte maker is brewing coffee or frothing. Wait until the brew cycle is complete before removing any of these parts.

Correct Use of Ground Coffee for Espresso Makers

Do not use sugar roasted* ground coffee or sugar roasted coffee beans as these will clog the filter and damage the appliance. If sugar roasted coffee is accidentally used, stop using the unit and contact Oster Consumer Service for maintenance.

Oster recommends descaling the machine periodically to keep it in good working condition. Contact Oster Consumer Service Centers as listed on separate insert to learn about this process.

(*) Ground with sugar

Description of the Appliance

The Oster BVSTEM6601 Series appliance features various components for brewing and frothing. Refer to the following list for identification:

1. Brew Head
2. Porta-Filter
3. Frothed Milk Dispensing Tube
4. Cup Height Adjusting Drawer
5. Removable Drip Tray and Drip Grid
6. Drip tray Overflow Indicator
7. Porta-Filter Retention Clip
8. Filter for Single Shot of Espresso
9. Filter for Double Shot of Espresso
10. Measuring Scoop/Tamper
11. Milk Reservoir Lid
12. Froth Control Knob
13. Frothing Tube Lever
14. Removable/Clear Milk Reservoir
15. On/off Switch “I/O” (right side of appliance)
16. Water Reservoir Lid
17. Removable Water Reservoir

Control Panel

The control panel is divided into two parts: the left side indicates automatic brewing functions, and the right side indicates manual functions.

Lights Indicate:

• Button Light Pulses: Unit is heating up or unit is brewing/frothing/cleaning.
• Button Light Remains Illuminated: Unit is ready for use.
• Cappuccino and Latte Button Lights do not illuminate: Milk Reservoir not fully inserted in unit.
• Icon Lights illuminate: Indicates your brew selection.
• Button Light Flashes: Water Reservoir is empty or function selected before unit is ready.

Espresso (Button A):

• Automatic: Selects espresso size.
• Manual: Customizes the amount of espresso in your beverage.

Cappuccino (Button B):

• Automatic: Selects cappuccino size.
• Manual: Customizes the amount of frothed milk in your beverage.

Latte (Button C):

• Automatic: Selects latte size.
• Manual: Controls the cleaning cycle for the frothed milk dispensing tube.

Note: Please read the rest of the instructions before operating the Oster® espresso, cappuccino & latte maker.

Introduction

The Oster® Automatic Espresso, Cappuccino, and Latte Maker is an innovative appliance designed to prepare delicious espressos, cappuccinos, and lattes quickly, conveniently, and automatically with the touch of a button.

Espresso

A unique coffee brewing method where hot water is forced through finely ground coffee. It is a richer, more full-bodied brew, typically served in 44 to 59 mL portions in demitasse cups.

Cappuccino

A drink made with approximately ¼ espresso, ½ steamed milk, and ½ frothed milk.

Latte

A drink made with approximately ¼ espresso and ¾ steamed milk.

It is important to read all instructions, cautions, notes, and warnings in this manual carefully before using the appliance. Proper care and maintenance will ensure the long life and trouble-free operation of the Oster® Automatic Espresso, Cappuccino, and Latte Maker. This appliance can be used with ground coffee, making it versatile for preparing single shots of espresso, cappuccino, and latte.

Important Safety Instructions

Please follow these important safety instructions while using the unit:

1. Before removing any parts and accessories, ensure the three lights are on, press the on/off switch to the off position “O”, and unplug the appliance.
2. Do not remove the porta-filter at any time during the brewing process.
3. Use caution when removing the porta-filter. Metal parts may still be very hot. Hot water may also be on top of the filter. Hold it by its handle and use the filter retention clip to dispose of brewed coffee grounds.
4. If coffee does not drip, the filter is blocked. Turn off the appliance and allow it to cool. Blockage may be caused by coffee being too finely ground. Refer to the "Problems and Causes" section.
5. When Cleaning the Frothed Milk Dispensing Tube: Place a large cup under the tube. Fill the milk reservoir with water and place it back on the unit. Turn the Froth Control Knob clockwise to the clean position (?). Press the latte/clean button for 3 seconds and release to activate the clean function. Let the unit dispense water through the tube for approximately 30 seconds, then press the Latte/Clean Button once to stop the process.

Note: For proper unit function, clean it after every use.

Before Using Your Appliance for the First Time

Cleaning and Priming the Unit Prior to First Use

Familiarize yourself with the appliance parts by referring to the “Description of the Appliance” section.

1. Ensure the unit is off "O" by pressing the on/off “I/O” button and is unplugged from the electrical outlet.
2. Remove stickers and labels.
3. Wash the water reservoir, milk reservoir, porta-filter, three filters, and measuring scoop with mild detergent and water. Rinse thoroughly and place them back.
4. Refer to "Placing the Porta-Filter" instructions before placing or removing the porta-filter and filter.
5. To clean the inside, follow "Preparing Cappuccino" steps using water in both reservoirs and no coffee in the filter. Do not immerse the appliance in water or attempt to reach internal parts.

Important - Prime the Unit

To prime the unit, run the steam cycle for 90 seconds:

1. Fill water reservoir to “MAX” level.
2. Fill milk reservoir to "Max Fill” level and slide it firmly into place.
3. Select a filter, place it on the porta-filter, lock the porta-filter into the unit, and place a cup under the frothed milk dispensing tube.
4. Plug the appliance into the outlet.
5. Turn the power button on “I”.
6. The three control panel lights will blink. Once solid, press the Espresso button (☕) and hold for 3 seconds, then release. Let water flow for up to 90 seconds.
7. Press the Espresso button (☕) again to stop.
8. Press the Cappuccino button (☕) and hold for 3 seconds, then release. Let water flow for up to 90 seconds.
9. Press the Cappuccino button (☕) again to stop.
10. The three control panel lights will turn solid, indicating the unit is ready.

Your unit is now primed and ready for use.

Selecting the Right Cup

Choose the correct cup size based on the beverage type:

Selecting the Right Coffee

The Coffee

Coffee should be freshly ground and dark roasted, such as French or Italian roast. Pre-ground coffee retains flavor for 7-8 days in an airtight container in a cool, dark area. Whole beans are recommended to be ground just before use, retaining flavor for up to 4 weeks.

The Grind

The grind is vital for espresso making. It should be fine, like salt. If too fine (like powder), water won't flow under pressure. If too coarse, water flows too fast, preventing full-flavored extraction. Use a quality grinder for uniform consistency.

Operating Instructions

Filling the Water Reservoir

1. Fill the reservoir with water, either by using a jar or by removing it and filling under the tap. Ensure it is placed back tightly and filled below the "MAX" line. Never use warm or hot water.
2. Close the water reservoir lid and place it back in the unit tightly.

Filling the Milk Reservoir

For cappuccino or latte, remove the milk reservoir, open the lid, and pour cold milk up to the “Max” level. Place the milk reservoir back tightly. The Cappuccino and Latte buttons will illuminate or pulse.

Note: Any type of milk (whole, low-fat, organic, soy) can be used.

Choosing the Filter

Select the appropriate filter:

1. For a Single Shot: Use the filter for a single shot of espresso if using ground coffee.
2. For a Double Shot or Two Single Shots: Use the filter for a double shot.

Inserting the Filter

1. To insert the selected filter in the porta-filter, align the notch on the filter with the groove inside the porta-filter.
2. Turn the filter to the left or right to lock it securely in place within the porta-filter.

Note: To remove and clean the filter, turn it to the left or right to align the filter notch with the groove inside the porta-filter.

Warning: Ensure the filter has cooled before attempting to remove it.

Filling with Coffee

1. Fill the filter with fresh, fine ground espresso coffee (do not overfill).
2. Tamp and compress firmly and evenly. Coffee should be 3mm below the top of the filter after tamping.
3. Clean any excess coffee from the rim to ensure proper fit under the brew head and avoid leaks.

Placing the Porta-Filter

1. Position the porta-filter underneath the brew head, moving the retainer clip back first.
2. Position the handle so it lines up with the open lock icon (?) on the unit and fits into the groove.
3. Slowly turn it to the right until the retention clip is aligned with the closed lock symbol (?) on the unit.

Placing the Cup(s)

1. Pull out the height adjustment tray for a small “demitasse” cup for espresso.
2. Keep the height adjustment tray inside its compartment for a larger cup for cappuccino.
3. Keep the height adjustment tray inside its compartment for a larger cup for latte.

Caution: When brewing cappuccino or latte, adjust the frothing tube lever to point inside the cup.

Turning the Unit On

1. Ensure the unit is plugged in.
2. Turn the unit on "I".

The three control panel lights will blink during heating until the water reaches the perfect temperature. Once solid, the unit is ready.

Note: The Espresso function typically becomes ready before Cappuccino and Latte functions.

Note: If left on for 15 minutes without use, the unit will enter sleep mode. Press any button to reactivate.

Select the Function

Preparing Espresso

1. Press the Espresso Button (☕) once to brew a single shot.
2. Press the Espresso Button (☕☕) twice to brew a double shot.
3. Press and hold the Espresso Button (☕) for 3 seconds to customize brewing. When done, press the Espresso Button (☕) once again to stop. For safety, the unit automatically stops after brewing 148ml (5 ounces).

The unit will start brewing espresso according to your selection. It will turn off automatically, and lights will become solid, indicating completion. Your espresso is ready.

Note: To brew less coffee than the preset serving, press the function button to stop the brewing process when the desired amount is reached.

Preparing Cappuccino

Adjust the quantity of frothed milk by turning the Froth Control Knob: right for more froth, left for less froth. This can be adjusted during the brewing cycle.

1. Press the Cappuccino Button (?☕) once to brew a small cup of cappuccino.
2. Press the Cappuccino Button (??☕☕) twice to brew a large cup of cappuccino.

Note: For a small cup, use the single shot filter. For a large cup, use the double shot filter.

Preparing Latte

Adjust the quantity of frothed milk by turning the Froth Control Knob: right for more froth, left for less froth.

1. Press the Latte Button (?) once to brew a small cup of latte.
2. Press the Latte Button (??) twice to brew a large cup of latte.

Note: For a small cup, use the single shot filter. For a large cup, use the double shot filter.

Preparing Froth Milk

The Oster® Automatic Espresso, Cappuccino, and Latte Maker also allows preparing froth milk only. Press and hold the Cappuccino Button (?☕) for 3 seconds to add more froth to your beverage or prepare froth milk for other beverages (e.g., macchiato, hot chocolate, chai latte). When done, press the Cappuccino Button (?☕) once again to stop.

After Preparing Your Beverages with Milk

After preparing your beverage with milk, you can store the unit's milk reservoir directly in the refrigerator (ready for next use) or dispose of leftover milk.

Cleaning Your Automatic Espresso, Cappuccino, and Latte Maker

Cleaning the Milk Reservoir and Frothing Tube

Regular cleaning of the milk reservoir and frothing tube is important to avoid clogging and residue buildup, even if storing milk in the refrigerator.

1. Place a large empty cup under the frothing tube and ensure water is in the water reservoir.
2. Aim the Frothed Milk Dispensing Tube into the empty cup.
3. Adjust the Froth Control Knob to the "Clean" position (?).
4. Press and hold the Clean button (?) for 3 seconds, then release. The clean function runs for 30 seconds. Discard contents.
5. Discard remaining milk, rinse, and wash the milk reservoir and lid thoroughly with warm soapy water. Rinse and dry well. Do not use abrasive cleaners or scouring pads. The milk reservoir and lid are dishwasher safe (top rack).

Cleaning the Brew Head, the Porta-Filter and Filter

1. Switch the power button to "O" and unplug the power cord.
2. Allow hot metal parts to cool before touching.
3. Remove the porta-filter, discard coffee grounds. Wash porta-filter and filter with warm soapy water and rinse well. Do not wash in dishwasher.
4. Wipe the lower part of the brew head with a damp cloth or paper towel to remove any leftover coffee grounds.
5. Place the porta-filter (without filter) back in the brew head.
6. Place an empty large cup under the porta-filter.
7. Press the espresso button (☕) once and let the unit brew with water only until it stops automatically.
8. Allow the porta-filter to dry completely after cleaning.

Cleaning the Water Reservoir

Discard remaining water by removing the reservoir and turning it upside down over the sink. It is recommended to empty it between uses. Wash with soapy water, rinse well, and wipe dry. Do not wash in the dishwasher.

Cleaning the Unit

1. Wipe housing with a soft wet cloth. Do not use abrasive cleaners or scouring pads.
2. Do not store the porta-filter in the brew head, as this can adversely affect the seal during brewing.

Caution: Do not immerse appliance in water.

Deliming

Mineral deposits will affect appliance operation, increasing brewing time or excessive steaming. White deposits may appear on the brew head. Cleaning frequency depends on water hardness:

To Delime Water Reservoir:

1. Fill the reservoir with fresh, undiluted white household vinegar.
2. Allow appliance to sit overnight with the vinegar solution.
3. Discard vinegar by removing the reservoir and turning it upside down over the sink.
4. Rinse the water reservoir thoroughly with tap water, repeating twice.

To Delime Internal Parts:

1. First delime the water reservoir as above.
2. Switch the on/off button to "O" and disconnect the power cord. Fill the reservoir with white vinegar above the minimum level.
3. Insert the porta-filter (with filter, no coffee) and place a jar/carafe or cup on the drip tray and under the porta-filter.
4. Plug the power cord into the electrical outlet.
5. Press the on/off button to "I". Once the 3 control panel lights turn solid blue, press the Espresso/Custom Button (☕) twice. Vinegar will flow through the unit and stop automatically.
6. Place a pitcher or large cup (at least 325 mL/11-ounce capacity) under the tube. Fill the milk reservoir with water and place it back. Turn the Froth Control Knob clockwise to the clean position (?). Press the latte/clean button for 3 seconds to activate the clean function. Let the unit dispense water through the tube for approximately 30 seconds, then press the Latte/Clean Button once to stop.
7. Repeat Steps 1-6 as necessary using only tap water to rinse any remaining traces of vinegar.

Problems, Causes and Solutions

Warranty

Jarden Consumer Solutions of India Private Limited ("JCS") warrants this product for two (2) years from the date of purchase against defects in material and workmanship. The warranty card and cash memo, duly stamped and signed by the dealer, are required for claims.

This Warranty is additional to statutory rights. During the Warranty Period, JCS will repair or replace defective products or components free of cost, provided JCS is promptly informed, the product has not been altered or misused, and the warranty is made available. The warranty is non-transferable and applies to the original purchaser.

Any repaired or replaced product will be warranted for the remaining portion of the Warranty. Liability for consequential loss or damage is not accepted. This Warranty does not cover use other than intended, non-compliance with instructions, improper or reckless use, unauthorized alterations or repairs, incorrect installation, defects caused by natural disasters, incorrect current/voltage, normal wear and tear, transportation damage, or commercial use.

JCS is not responsible for service delays due to component unavailability or reasons beyond its control. JCS's liability for damages is limited to the sale invoice amount.

Waste electrical products should be recycled where facilities exist.

Authorized Service Centers

A comprehensive list of authorized service centers is provided for various regions across India, including West Bengal, Delhi, Haryana, Uttar Pradesh, Punjab, Himachal, Rajasthan, Maharashtra, Goa, Gujarat, Madhya Pradesh, Tamil Nadu, and Karnataka. Each entry includes the city, service center name, address, contact person, and contact number for customer support and repairs.

For specific details, please refer to the complete list provided in the original document or visit www.oster.in.