Marea B59004 Smartwatch User Manual

Cautions before using

1. The company reserves the right to modify the contents of this manual without any further notification. It is normal that some functions may vary in certain versions of software.
2. Please charge this product with the charger provided for no less than 2 hours before using it for the first time.
3. In the APP, set personal information to sync time before using the smart watch. Please refer to the instructions about synchronization for details.
4. The watch has IP68 waterproof rating. It cannot be used in corrosive liquids or hot water, tea, etc. It is not compatible with deep sea diving of more than 3 meters. All the above situations will cause damage to the smart watch (these damages will not be covered by the warranty).

1. Product overview

The Marea B59004 is a smartwatch designed for health and fitness tracking.
Visual Description: A pink smartwatch with a square display. The watch face shows the time "10:45", day "SÁBADO 09", temperature "36.8°C", and a heart icon with "098".

Watch Components:

• Display zone
• Touch screen
• Button
• Magnetic charging port
• Heart rate testing sensor

Models can be paired with:

• Android phone: supports OS 5.0 and above
• iPhone: supports OS 9.0 and above

2. APP download and connection

1. Go to the website www.mareasmart.com and find your smart watch model. The model number is found on the back of the smart watch (it starts with "B" and is followed by five digits).
2. Download and install the official app that corresponds with your smart watch model on your phone.
3. Open the app and enable all the permissions that the app requests.
4. Turn on Bluetooth on your phone.
5. Make sure that the smart watch has not been linked directly through Bluetooth to your phone. If so, unlink it.
6. Bind your Marea Smart watch through the app.

Note for Apple phone users: If the phone is in standby or hibernation state for a long time (e.g., 2 hours or more, not used, black screen state), the APP may be cleaned up by the iOS system, causing disconnection. Re-opening the app will automatically reconnect.

Note for Android phone users: After installing the APP, enable background application launch permission in your phone's settings. For example, on Huawei phones: Settings > Application > Application Launch Management > Official APP Sport > change to manual management > allow Auto-launch, Secondary launch, Run in background. This ensures the Bluetooth connection is maintained when the phone is in standby mode.

2.2 Link APP and smart watch

1. Open the application, choose "Register" or "Login without registering".
2. For Android users: click on "Pair new device" and select the model that corresponds with your smart watch. The QR code scanner will open.
3. Open the QR code on the watch and scan to link the watch. Connection takes about 30 seconds. Confirm all permission requests to ensure full functionality.
4. For iPhone users: the "pair new device" request will appear on your phone after scanning.
5. If the QR code scan fails, select the manual connection function to complete the pairing via Bluetooth.

2.3 APP settings

(Functions are available only if watch and phone have been paired successfully)

• Call notification: Tap to turn on/off. If turned on, you can hang up the incoming call on your watch.
• Social media notifications: Tap to turn on/off and select which apps' notifications to receive.
• Alarm clock: Supports up to 5 alarms.
• Sedentary reminder: Tap to turn on/off. Set starting time, end time, interval, and threshold.
• Drink water reminder: Tap to turn on/off. Set starting time, end time, interval, and threshold.
• DND mode (Do not disturb mode): Tap to turn on/off. Set starting time and end time. When turned on, the watch will not receive notifications.
• Turn on screen when turning wrist: Tap to turn on/off.
• Heart rate monitoring: Tap to turn on/off. Set starting time, end time, and interval. When turned on, the watch automatically monitors heart rate and syncs data to the APP.
• Remote camera control: (On some phones, the camera may need to be opened manually).
• Find device: Tap to make the watch display an icon and vibrate.
• Firmware update: Ensure at least 50% battery before updating and keep the watch near your phone.
• Device version: Check the firmware version of the watch.
• Unbound: For iPhone users, go to phone settings, Bluetooth settings, and ignore the device to disconnect completely.

3. Main functions

3.1 Basic Operation

• Power on: Long press the button for 3 seconds. Short press the button to light up the watch if it is in standby mode.
• Power off: If the screen is on, long press the button for 3 seconds to turn the watch off.
• Watch interface shift process:
  1. Slide from top to bottom on the main screen dial to see the status bar (includes DND mode [DND], brightness level, settings [settings], connection icon [connection], and battery [battery]).
  2. Slide from right to left on the main screen to enter the menu.
  3. Slide from left to right on the main screen to see health and sleep data.
  4. Slide from bottom to top on the main screen to see received messages.

3.2 Main screen selection

Long press the screen for 3 seconds to display all options. Slide left and right to choose the preferred main screen. Single touch to set it as the default.

3.3 Pedometer

The watch automatically records steps, distance, and calories. To see pedometer data, swipe right from the watch's main screen or swipe left from the main screen to access the menu.

3.4 Sport mode

Sport modes include outdoor walking, indoor walking, outdoor running, indoor running, cycling, hiking, and swimming. This smartwatch is not equipped with GPS, so results for modes requiring A-GPS may vary with different phones.

• Click the icon to enter a sport mode and customize the goal (distance, time, or calories) or set no goals. The watch saves the setting for future use.
• Historical data: Saves the last 8 records, displayed chronologically. View by sliding up and down.

Note: Data is saved only if exercise time is over 5 minutes or steps exceed 200.

When starting a recording, the watch screen displays the sport type and start time. Swipe up and down for detailed records.

Goal completion: The watch displays 'Goal completed' when a preset goal is achieved. Recording continues if the exercise continues.

3.5 Sleep Monitor

The default sleep monitor runs from 21:00 to 7:30 the next day. If worn during sleep, sleep time can be checked in the morning. Paired with the phone, sleep data syncs automatically (or manually) with the app.

Note: The watch automatically identifies sleeping status. Detected data may differ from actual data during the detection process. The final result displayed after monitoring is complete will be identical to actual sleep data. Deviations may occur due to changes in sleep modes.

3.6 Health

• 3.6.1 Heart rate: Displays "--Bpm". Test begins after two seconds. Data is shown on the watch screen and updated continuously. Swipe right to stop detection. Historical data (highest, average) is available in the app.
• 3.6.2 Blood pressure: Displays "--mmHg". Test begins after two seconds. Data is shown on the watch screen and updated continuously. Swipe right to stop detection.
• 3.6.3 Blood oxygen: Displays "--%". Test begins after two seconds. Data is shown on the watch screen and updated continuously. Swipe right to stop detection.

Note: Heart rate, blood pressure, and blood oxygen tests take about 10-30 seconds to generate data.

3.7 Notifications (messages)

After pairing and activating notifications, phone messages sync to the watch. The watch saves the last 8 messages, which can be deleted by sliding up and tapping the trash can icon [trash].

Messages can be read on the watch, but cannot be answered, and audio cannot be played.

3.8 Alarm clock (only set via APP)

The application supports setting a maximum of 5 alarms.

3.9 Remote music player

• If the watch is not paired, clicking the 'Music' icon shows an 'unconnected' message and exits after 2 seconds.
• After pairing, the watch can control the phone's music player. Compatibility issues may arise with different players; some may require manual opening on the phone.
• The watch can pause [pause], play [play], and switch tracks [previous], [next], but does not display song names or adjust volume.

3.10 Pairing with QR code

In the application, select "Pair new device" to scan the watch's QR code [QR code] to link with the phone. A blue "connection" icon [connection] appears in the watch's drop-down menu when connected. Each watch connects to one phone only.

3.11 Timer

Set target time, click the start icon. A "timed out" message appears, and the watch vibrates.

3.12 Stop watch

Click the start icon to begin counting. Click the Pause icon [pause] to stop. Click the clock icon to set a lap time. If stopped, the clock icon changes to two arrows [arrows]. Clicking it stops counting and clears records. The watch keeps records of up to 20 lap times.

3.13 Temperature

For accurate measurement, wear the smartwatch for at least 15 minutes. Measurement must be done indoors in stable conditions, avoiding drafts, air conditioning, and heating.

When pressing Accept, the display shows "--ºC". Data is shown on the watch screen when skin and body temperature data are detected. Swipe right to stop detection. Historical data, including graphics, is available in the app.

3.14 Find phone

If the watch is paired, clicking "Find phone" on the watch makes the phone vibrate and ring.

3.15 Settings

• Screen brightness setting: 5 levels of brightness; click the screen to adjust.
• QR code to download the app: Scan this QR code [QR code] with your phone to download the latest app version.
• Remote camera control: If paired, clicking the camera function on the watch shows a camera icon [camera] and opens the phone's camera. Clicking the watch icon takes a photo saved to the phone's album. Some phones may require manual camera opening first.
• Reset: Tap the left icon to exit, tap the right icon to reset. All watch data will be cleared. Paired phone data is not cleared unless the phone is also reset.
• About: View the device's Mac address, Bluetooth name, and firmware version.

4. Precautions

• Only one smartwatch pairing application should be installed on the phone for normal connection. Multiple applications can affect the connection.

Note: Some Android phones may prompt that installation is not allowed. Go to phone 'settings' and authorize 'Unknown source'.

• When the mobile phone requests permissions, click "Allow". Denying permissions may prevent receiving notifications, scanning QR codes, using remote camera, or other functions. These permissions do not affect phone operation or data flow.
• Some Android phones may close apps when cleaning. Keep the official app running in the background.

Android phone settings (background running): Go to phone settings > application management > Official APP > Rights management > Backstage management > select background running. (Settings may vary by phone model/version).

• Heart rate monitoring requires contact between the watch and arm. The watch should not be too tight (affects blood flow) or too loose (affects sensor monitoring).
• Avoid hitting the smartwatch, as it could break the glass.
• Use 5V, 1A for charging. Fast charging is not supported. Do not charge if the watch has water or sweat to prevent short circuits and damage.
• This product is an electronic monitoring product, not for medical reference.

5. Troubleshooting

If problems occur, follow these steps. If unresolved, contact the seller or designated maintenance personnel.

5.1 The watch cannot be turned on:

• Press the display touch area for over 3 seconds.
• Ensure there is enough battery. Charge if power is low.
• If the smartwatch has not been used for a long time and the normal charger doesn't respond, try charging with a 5V/1A output power.

5.2 It shuts down automatically:

• Battery power may be too low; please charge it.

5.3 Short battery life:

• Ensure the battery is fully charged (at least 2 hours required).
• Charger or data cable may be faulty; replace them.
• Check the data cable port and try again to ensure a proper connection.

5.4 Bluetooth disconnects or unable to connect:

• Please restart the watch.
• Turn off Bluetooth on the mobile phone and then turn it back on to reconnect.

5.5 Inaccurate sleep data:

The sleep monitor mimics natural sleep patterns. Use the smartwatch during the day. Using it only during sleep or going to bed late may cause deviations. Sleep data may not be generated if you go to bed during the day, as the default sleep time is set between 9:00 p.m. and 7:30 a.m.