DZS Q1G 2428GN Quick Installation Guide
Introduction
Package Content
The DZS 2428GN package typically includes the following items:
- DZS 2428GN Device
- Power Adapter
- Ethernet Cable
- Quick Installation Guide (this document)
- Warranty Card
Specifications
| Specification | Details |
|---|---|
| Model | DZS 2428GN |
| CPU | 800 MHz Dual-Core |
| Memory | 256 MB DDR3 |
| Flash | 128 MB |
| WAN | 1 x 10/100/1000 Mbps Gigabit Ethernet Port |
| LAN | 4 x 10/100/1000 Mbps Gigabit Ethernet Ports |
| Wi-Fi | 802.11a/b/g/n/ac, Dual-Band (2.4GHz & 5GHz) |
| Power | 12V DC, 1.5A |
| Dimensions | 180 x 130 x 30 mm (W x D x H) |
| Weight | 350 g |
| Operating Temp | 0°C to 40°C (32°F to 104°F) |
| Storage Temp | -20°C to 70°C (-4°F to 158°F) |
| Humidity | 5% to 95% non-condensing |
Interface
Device Overview
The DZS 2428GN features a comprehensive interface for connectivity and management. The front panel includes status LEDs, a WAN port, four LAN ports, a WPS button, a reset button, and a USB port. The side panel provides access to the power input, a recessed reset button, the WPS button, a USB port, and a console port.
LED Indicators
| LED Name | Color | Status | Description |
|---|---|---|---|
| Power | Green | Solid | Device is powered on. |
| Off | Device is powered off. | ||
| WAN | Green | Solid | WAN link is up. |
| Blinking | WAN data activity. | ||
| Off | WAN link is down. | ||
| LAN1-4 | Green | Solid | LAN link is up. |
| Blinking | LAN data activity. | ||
| Off | LAN link is down. | ||
| Wi-Fi | Green | Solid | Wi-Fi is enabled and broadcasting. |
| Blinking | Wi-Fi data activity. | ||
| Off | Wi-Fi is disabled. | ||
| USB | Green | Solid | USB device connected and recognized. |
| Blinking | USB data activity. | ||
| Off | No USB device connected or recognized. | ||
| WPS | Blue | Blinking | WPS pairing process is active. |
| Off | WPS is not active. |
Installation
Mounting the 2428GN
The 2428GN can be mounted on a wall or placed on a flat surface. For wall mounting, use appropriate screws (not included) to secure the device through the mounting slots on the back panel. A diagram shows the back of the device with mounting slots and illustrates wall attachment.
Connecting the 2428GN
Follow these steps to connect your DZS 2428GN device:
- Connect the power adapter to the DC IN port on the back of the device and plug the adapter into a power outlet. A diagram shows the power adapter connecting to the device.
- Connect one end of an Ethernet cable to the WAN port on the device and the other end to your modem or internet source. A diagram illustrates this connection.
- (Optional) Connect computers or other devices to the LAN ports using Ethernet cables.
Caution and Safety
General Warnings
⚠️ To avoid electrical shock, disconnect the power cord before servicing or removing the unit. Ensure that the unit is properly grounded. Do not operate the unit in wet or damp conditions. Do not open the unit casing; refer servicing to qualified personnel only. The power adapter is used as a disconnect device; its access shall remain readily operable.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment into an outlet on a circuit different from that to which the receiver is connected, or consulting the dealer or an experienced radio/TV technician for help.
Limited Warranty
DZS warrants this product to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase. This warranty does not cover damage caused by accident, misuse, abuse, or modification.
Web Access
You can access the 2428GN via a web browser for configuration and management. To do so, connect your computer to one of the 2428GN's LAN ports. Open a web browser and navigate to the default IP address: 192.168.0.1. Log in using the default credentials: username 'admin' and password 'admin'.
Voltage Detector
A diagram illustrates an "All-in-One Voltage Detector" with connection points labeled A, B, C, and D, used for voltage detection during setup or testing.
