OVATION F-165WW Quick Reference Guide
About this Guide
The OVATION F-165WW Quick Reference Guide (QRG) provides basic product information including connection, mounting, menu options, and DMX values. For more detailed information, download the User Manual from www.chauvetprofessional.com.
Disclaimer
The information and specifications in this QRG are subject to change without notice.
Safety Notes
- DO NOT open this product. It contains no user-serviceable parts.
- DO NOT look at the light source when the product is on.
- To prevent unnecessary wear and prolong lifespan, disconnect the product from power during periods of non-use (via breaker or unplugging).
- CAUTION: When transferring the product between extreme temperature environments (e.g., from a cold truck to a warm, humid ballroom), condensation may form on internal electronics. To avoid failure, allow the product to fully acclimate to the surrounding environment before connecting to power.
- CAUTION: This product's housing may be hot when lights are operating.
- Mount this product in a location with adequate ventilation, at least 20 inches (50 cm) from adjacent surfaces.
- DO NOT place flammable material within 50 cm of this product while operating or connected to power.
- USE a safety cable when mounting this product overhead.
- DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
- DO NOT operate this product if the housing, lenses, or cables appear damaged.
- DO NOT connect this product to a dimmer or rheostat.
- ONLY connect this product to a grounded and protected circuit.
- ONLY use the hanging bracket to carry this product.
- In case of a serious operating problem, stop using immediately.
- The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
Contact Information
For support or returns outside the U.S., United Kingdom, or Ireland, contact your distributor. Visit www.chauvetlighting.com for contact details.
What is Included
- OVATION F-165WW fixture
- Neutrik® powerCON® power cord
- Safety Cable
- Gel frame (7.5 in/191 mm accessories)
- Warranty Card
- Quick Reference Guide
AC Power
This product features an auto-ranging power supply compatible with input voltage ranges of 100–240 VAC, 50/60 Hz.
Power Linking
Up to 4 OVATION F-165WW products can be linked at 120 VAC, or 7 products at 230 VAC. Do not exceed this number. Power linking cords are sold separately.
AC Plug Wiring
| Connection | Wire (U.S.) | Wire (Europe) | Screw Color |
|---|---|---|---|
| AC Live | Black | Brown | Yellow/Brass |
| AC Neutral | White | Blue | Silver |
| AC Ground | Green/Yellow | Green/Yellow | Green |
Replacing the Fuse
- Disconnect the product from power.
- Using a Phillips #2 head screwdriver, unscrew the fuse holder cap from the housing.
- Remove the blown fuse and replace it with a good fuse of the same type and rating.
- Screw the fuse holder cap back in place and reconnect power.
DMX Linking
The OVATION F-165WW works with a DMX controller via a standard DMX serial connection. A DMX Primer is available at www.chauvetprofessional.com.
DMX Connection
The OVATION F-165WW supports DMX data connections for its DMX personalities: UNO, DOS, and STD.P. Refer to the User Manual for connection and configuration details.
Master Control
The OVATION F-165WW can control other OVATION F-165WW products using a standard DMX data connection. Consult the User Manual for Master Control configuration.
Master/Slave Connection
The OVATION F-165WW uses the DMX data connection for its Master/Slave mode. Refer to the User Manual for connection and configuration.
Mounting
Product Diagram
The product diagram illustrates the OVATION F-165WW fixture. It shows the mounting yoke and points for attaching a safety cable. The safety cable should be secured using the passageway on the side of the product.
Overhead Mounting
When mounting overhead, ensure the safety cable is securely attached to the designated point on the fixture.
Control Panel
Description
| Button/Knob | Function |
|---|---|
| <MENU> | Exits the current menu or function. |
| <ENTER> | Enables the currently displayed menu or sets the currently selected value into the selected function. |
| <UP> | Navigates upwards through the menu list and increases the numeric value when in a function. |
| <DOWN> | Navigates downwards through the menu list and decreases the numeric value when in a function. |
| <DIM> | Press twice rapidly to access the dimmer function. Use the knob to adjust dimmer intensity. |
| <ZOOM> | Press twice rapidly to access the zoom function. Use the knob to adjust the zoom. |
Passcode
When prompted, enter the following password: <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>. This password cannot be changed and must be used whenever prompted.
Menu Options
Main Level: STAT
| Programming Levels | Description |
|---|---|
| DIM | Local control of output |
| ZOOM | Local control of zoom lens |
Main Level: RUN
| Programming Levels | Description |
|---|---|
| DMX | Sets the mode to Master/Slave |
| SLAV | Sets the mode to Master/Slave |
Main Level: ADDR
| Programming Levels | Description |
|---|---|
| D.001-D.512 | Sets the starting address |
Main Level: MOTR
| Programming Levels | Description |
|---|---|
| YES | Resets the Zoom motor |
| NO | Resets the Zoom motor |
Main Level: SET
| Programming Levels | Description |
|---|---|
| KEY OFF | Sets the key lock (password mode). |
| KEY ON | Sets the key lock (password mode). |
| DIMX DIM1 | Slow (DIM4) to fast (DIM1) dimmer speeds. |
| DIMX DIM2 | Slow (DIM4) to fast (DIM1) dimmer speeds. |
| DIMX DIM3 | Slow (DIM4) to fast (DIM1) dimmer speeds. |
| DIMX DIM4 | Slow (DIM4) to fast (DIM1) dimmer speeds. |
| CURV CV1 | Large (CV3) to small (CV1) dimmer curves. |
| CURV CV2 | Large (CV3) to small (CV1) dimmer curves. |
| CURV CV3 | Large (CV3) to small (CV1) dimmer curves. |
| CURV OFF | Large (CV3) to small (CV1) dimmer curves. |
Main Level: SET (Cont.)
| Programming Levels | Description |
|---|---|
| REST (Enter Passcode) REST OK | Resets fixture to factory defaults. |
| PERS UNO | Selects DMX personality. |
| PERS DOS | Selects DMX personality. |
| PERS STD.P | Selects DMX personality. |
| SLCK OFF | SET menu level access lock. |
| SLCK ON | SET menu level access lock. |
| DERR BLAK | Blacks out fixture upon loss of DMX. |
| DERR SAVE | Continues with last command upon loss of DMX control. |
| ZOOM BASE | Sets default zoom position (full movement). |
| ZOOM POS1 | Sets position 1 setting for zoom limit. |
| ZOOM POS2 | Sets position 2 setting for zoom limit. |
| PERF LIVE | Balances LED cooling using fans and output power level. |
| PERF STDO | Maintains LED cooling by limiting output power level. |
| PERF POWR | Maintains LED cooling using fans allowing full power output. |
| MCON SELF | No DMX data is sent in standalone operation. |
| MCON MAST | Sends DMX data to other OVATION F-165WW during standalone operation. |
Main Level: CAL
| Programming Levels | Description |
|---|---|
| **** (Enter Passcode) CALZ POS1 | Sets min/max position of zoom (000-255). |
| **** (Enter Passcode) CALZ POS2 | Sets min/max position of zoom (000-255). |
DMX Values
UNO
| Channel | Function | Value | Percent/Setting |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | 0–100% |
DOS
| Channel | Function | Value | Percent/Setting |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | 0–100% |
| 2 | Dimmer Fine | 000 – 255 | 0–100% |
STD.P
| Channel | Function | Value | Percent/Setting |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | 0–100% |
| 2 | Dimmer Fine | 000 – 255 | 0–100% |
| 3 | Strobe | 000 – 009 | No Function |
| 010 – 099 | Strobe (slow to fast) | ||
| 100 – 109 | No Function | ||
| 110 – 179 | Lighting Effect | ||
| 180 – 189 | No Function | ||
| 190 – 255 | Random Strobe | ||
| 4 | Zoom | 000 – 255 | 0–100% |
| 5 | Motor Reset | 000 – 200 | No Function |
| 201 – 220 | Motor Reset | ||
| 221 – 255 | No Function |
