Chauvet Professional COLORado PXL Curve 12 User Manual

2. Introduction

Description

The COLORado PXL Curve 12 is a fully pixel-mappable motorized IP65-rated RGBW LED batten with individual control of zoom, tilt, and color across twelve independent heads. Basic and advanced operating modes, along with an extensive library of pre-built effects including virtual gobos, movement macros, and foreground/background color control, enable the creation of complex and volumetric looks. Seamless edge-to-edge mounting maintains pixel pitch between fixtures, ensuring consistent runway effects. The COLORado PXL Curve 12 supports DMX, sACN, Art-Net, Kling-Net, and RDM protocols.

Features

• IP65 batten with (12) 45W RGBW LEDs, (12) individually controllable tilting heads with a 5.7° to 36.3° zoom range.
• Maintains pixel pitch between fixtures.
• Quiet and quick operation of 200° of tilt for each of the (12) heads.
• Quiet and quick operation of (12) individual zoom zones.
• Fully pixel mappable.
• Several built-in effects including virtual gobos and movement macros with foreground and background color control for easy pixel animation effects.
• DMX, sACN, Art-Net, and Kling-Net control for full flexibility.
• RDM-enabled for remote addressing and troubleshooting.
• 5.7° to 36.3° zoom range for variable beam sizes.
• TRUE1-compatible power input/output ports.
• IP65-rated 5-pin DMX and TCP/IP input/output ports.
• IP65-rated USB-C software upload port.
• Slotted Omega brackets for easy hanging on truss.

Product Overview

The product features control elements and connection ports. On the top surface, there are menu buttons, a display screen, handles for carrying, and Omega brackets for mounting. On the rear, connection ports are visible: DMX in, Network in, Fuse holder, Power in, Safety loop, Power out, USB-c port, DMX out, Network out, and a condensation valve.

Product Dimensions

The fixture has a length of 39.49 inches (1,003 mm), a width of 6.65 inches (169 mm), and a height of 12.76 inches (324 mm). The overall depth is approximately 7.09 inches (180 mm).

3. Setup

AC Power

Each COLORado PXL Curve 12 is equipped with an auto-ranging power supply compatible with input voltages from 100 to 240 VAC, 50/60 Hz. Power requirements for each unit are listed on the product label and in the Technical Specifications chart. The listed current rating indicates the maximum current draw during normal operation. For circuit breaker sizing information, consult the Chauvet website: www.chauvetprofessional.com.

Important Safety Notes for AC Power:

• Always connect the product to a protected circuit (breaker or fuse) and ensure proper electrical grounding to prevent electrocution or fire.
• To minimize wear and extend lifespan, disconnect the product from power when not in use.
• Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if it functions as a 0-100% switch.

AC Plug Wiring

The unit includes a power input cord with a Seetronic Powerkon IP65 connector and an Edison plug (U.S. market). For wiring a plug, refer to the following table:

Power Linking

Multiple COLORado PXL Curve 12 units can be power linked. The table below shows the current draw at various voltages and frequencies. Ensure no single circuit exceeds 12A. Power-linking cables are sold separately.

Signal Connections

The COLORado PXL Curve 12 supports DMX, Art-Net™, sACN, or Kling-Net signals. It features two Neutrik RJ45 ports for Ethernet and 5-pin XLR ports for DMX input and output. These allow for individual control when used with compatible products.

Control Personalities

The fixture supports DMX, Art-Net™, sACN, and Kling-Net control personalities. The available modes are:

Note: In Dual Control mode, the Movement and Pixels protocols cannot be the same. Refer to the Operation section for configuration details and the DMX Values section for personality specifics.

DMX Linking

The fixture can be linked via a 5-pin DMX connection or WDMX. For DMX information, consult the DMX primer at: https://www.chauvetprofessional.com/wp-content/uploads/2016/06/DMX_Primer.pdf.

Art-Net™ Connection

Art-Net™ is an Ethernet protocol for transferring DMX512 data over IP networks using RJ45 connections. More information is available on the Chauvet website.

sACN Connection

sACN (ANSI E1.31) is an Ethernet protocol for transporting DMX512 data over IP networks.

Remote Device Management

RDM allows bidirectional communication for DMX-enabled devices. The COLORado PXL Curve 12 supports RDM for remote addressing and troubleshooting.

Connection Diagram

The connection diagram illustrates a typical network setup. It shows a switch or router connecting to a computer or controller running Art-Net™ or sACN protocols. Multiple COLORado PXL Curve 12 units can be connected to this network, along with other Art-Net™ or sACN devices.

USB Software Update

Software updates can be performed via the built-in USB-C port. To enable/disable this function, navigate to Setup > USB Update and select YES or NO. For updates, power on the fixture, insert a USB flash drive with the firmware file (.chl) in the root directory (FAT32 format, max 32GB). The display will prompt for firmware upgrade upon detection. Follow on-screen instructions.

Mounting

Refer to the Safety Notes before mounting. For Chauvet Professional mounting clamps, visit http://trusst.com/products/.

Orientation

Mount the product securely in a safe position, ensuring adequate ventilation, configuration, and maintenance access.

Rigging

Chauvet recommends the following rigging guidelines: Ensure easy access for maintenance and programming. Verify that the mounting structure and attachment points can support the product's weight (refer to Technical Specifications). Always use a safety cable for overhead mounting. Secure the product to a rigging point (platform or truss). Use appropriate mounting clamps for truss rigging. Position units close together for power linking.

Procedure

The COLORado PXL Curve 12 includes a bracket for attaching mounting clamps (sold separately). Ensure clamps are rated for the product's weight and use at least one mounting point per product. For Chauvet Professional clamps, visit http://www.trusst.com/products.

Mounting Diagram

The mounting diagram shows how to attach a mounting clamp and safety cable to the fixture's Omega bracket.

4. Operation

Control Panel Operation

The control panel buttons function as follows:

• <MENU>: Exits the current menu or function.
• <ENTER>: Enables the displayed menu or sets the selected value.
• <UP>: Navigates up or increases a numeric value.
• <DOWN>: Navigates down or decreases a numeric value.

Protocol Configuration

The COLORado PXL Curve 12 can be configured to respond to DMX, Art-Net™, sACN, Kling-Net, or a combination of these protocols to ensure correct controller response.

Control Mode

The fixture can operate with a single controller or two controllers using different protocols. In Dual Control mode, one protocol manages Movement, and the other manages Pixels. Single Control mode supports DMX, Art-Net™, and sACN. Dual Control Movement supports DMX, Art-Net™, and sACN. Dual Control Pixels supports DMX, Art-Net™, sACN, and Kling-Net.

To set the control mode and protocol:

1. Navigate to the Address main level.
2. Select the desired control mode (Single Control or Dual Control).
3. If using Dual Control, select the mode to configure (Movement or Pixels).
4. Select the desired protocol (DMX, Art-Net™, sACN, or Kling-Net for Dual Control Pixels only).

Note: In Dual Control mode, the Movement and Pixels protocols must be different. Refer to Network Settings for Ethernet protocol setup.

Control Personalities

To set the control personality:

1. Configure the control mode and protocol as described above.
2. Select the Personality option.
3. Choose the desired personality from the available modes (Single Control, Dual Control Movement, Dual Control Pixels).

Refer to the Starting Address section for recommended addresses and ensure no overlap between product starting addresses.

Starting Address

Each product and control mode requires a unique starting address for controller synchronization. Set the starting address between 001 and 512.

Universe

Art-Net™ and sACN protocols require a universe address in addition to the starting address. Set the universe between 000-255 for Art-Net™ or 001-256 for sACN.

Menu Map

Refer to the COLORado PXL Curve 12 product page on www.chauvetprofessional.com for the latest menu map.

DMX Values

Detailed DMX channel functions and values are provided for various control modes and personalities. These tables specify channel assignments, value ranges, and corresponding settings or functions.

Single Control Mode - Basic (20CH)

Dual Control Mode - Movement

Basic (8CH)

Basic2 (41CH) / Standard (53CH) / Advanced (59CH)

Dual Control Mode - Pixels

Basic (36CH) / Standard (48CH) / Advanced (96CH)

Tilt Macro

The Tilt Macro table lists values from 000 to 255, each corresponding to a specific tilt macro function or a range of values assigned to a macro.

Color Chart

The Color Chart table provides RGBW values for various color presets, including different white temperatures, primary colors, and color mixes. Each entry specifies the R, G, B, and W values or ranges for achieving specific colors.

Strobe Settings

The Strobe Settings table details the values and corresponding strobe effects, ranging from 'Off' to various 'fast to slow' patterns and random strobe effects.

Control Settings

The Control Settings table lists various operational parameters and their corresponding values, such as Blackout on tilt, color mixing modes, dimmer settings, PWM frequencies, and reset functions.

LED Macro

The LED Macro table lists values from 000 to 255, each assigned to a specific LED built-in function, indicating the range of values for each function.

Patterns

The Patterns section lists 256 patterns, numbered from 1 to 256, with corresponding visual representations (dots and lines) indicating the pattern sequence.

Configuration

Test Mode

Auto Test: To perform an automatic test of all functions, navigate to Run Mode > Auto Test.

Manual Test: To manually test functions, navigate to Run Mode > Manual Test, select the desired function (e.g., Tilt, Dimmer, Zoom), and adjust the value from 000-255.

Network Settings

To configure network settings (IP Mode, IP Byte, SubMask), navigate to Setup > Network Settings.

IP Mode

The IP address can be set manually, via DHCP, or using a static preset. Navigate to Network Settings > IP Mode and select the preferred option.

IP Byte

In Manual IP Mode, set the IP address by navigating to Network Settings > IP and selecting IP Byte 1 through 4, adjusting each byte's value from 000-255.

Subnet Mask

In Manual IP Mode, set the Subnet Mask by navigating to Network Settings > SMK and selecting SubMask 1 through 4, adjusting each value from 000-255.

Tilt Orientation

To set tilt orientation, navigate to Setup > Tilt Reverse and select NO (normal) or YES (reversed).

Zoom Orientation

To set zoom orientation, navigate to Setup > Zoom Reverse and select NO (wide to narrow) or YES (narrow to wide).

Display Orientation

To adjust display orientation, navigate to Setup > Screen Reverse and select NO (normal), YES (inverted), or AUTO (automatic detection).

Tilt Angle Range

To set the tilt angle range, navigate to Setup > Tilt Angle and select 200 (200°), 180 (180°), or 60 (60°).

Blackout on Tilt Movement

To enable or disable blackout during tilt movement, navigate to Setup > BL. O. T Move and select NO (do not blackout) or YES (black out).

Backlight Timer

Set the display backlight timeout by navigating to Setup > Backlight Timer and selecting 30S, 1M, 5M, or ON.

Loss of Data

Configure the fixture's response to signal loss by navigating to Setup > Loss of Data and selecting Hold (retain last signal) or Close (black out LEDs).

Color-Mixing Mode

The fixture supports CMY emulation. Navigate to Setup > C Mixing Mode and select RGBW (additive) or CMY (subtractive).

Dimmer Curve

Adjust the dimmer curve by navigating to Setup > Dimmer Curve and selecting Linear, Square, I Squa, or SCurve.

Dimmer Speed

Set dimmer speed by navigating to Setup > Dimmer Speed and selecting Smooth or Fast.

LED Frequency

Change the LED Pulse Width Modulation (PWM) frequency by navigating to Setup > PWM Option and selecting the desired frequency (600Hz to 25KHz).

Cell Order

Set the cell activation order (left-to-right or right-to-left) by navigating to Setup > Cell Order and selecting 1-12 or 12-1.

Calibrated White

Activate calibrated white (7500K) by navigating to Setup > Calibrated White and selecting ON, OFF, or Custom (to adjust via White Balance).

White Balance

Adjust LED color maximum values for white light output. Navigate to Setup > White Balance, select the color (Red, Green, Blue, White), and set the value (000-255).

Preset Functions

The fixture stores three presets (A, B, C). Changes are saved to the current preset. Load presets via Setup > Preset Select. Presets can be uploaded to other units via DMX connection (Setup > Preset Sync).

Reset Functions

Reset specific functions (Tilt, Zoom) or all functions to their startup state via Setup > Reset Function.

Factory Reset

Restore factory default settings by navigating to Setup > Factory Settings and selecting YES.

System Information

View system status, including firmware version, running mode, address, temperature, fixture/LED hours, Art-Net info, UID, and fan speeds, via the Information menu.

Offset Mode

Fine-tune the home position of moving parts for optical path and tilt. Access the Zero Adjust menu by pressing and holding <MENU> from the Main Level screen, then entering passcode 2323.

Tilt Adjustment

In the Zero Adjust menu, select TILT and adjust the starting value from 000 to 255.

Zoom Adjustment

In the Zero Adjust menu, select ZOOM1 or ZOOM2 and adjust the starting value from 000 to 255.

MAC Address Adjustment

Adjust the last three digits of the MAC address by selecting MAC4, MAC5, or MAC6 in the Zero Adjust menu and setting the value from 000 to 255.

Web Server

Access the fixture's web server from any computer on the same network for system information, control setup, manual testing, and firmware updates. Connect to power, set Art-Net™ and Static IP mode. Connect to a Windows® computer via network cable. Set the computer's IP address to match the first three digits of the fixture's IP. Access the web server via browser using the fixture's IP address, logging in with username 'admin' and password 'admin'. The web server offers Information, Setup, Manual Test, Firmware Update, and Security pages.

5. Technical Information

Product Maintenance

Regular cleaning is essential for optimal performance and longevity. Clean the product at least twice a month to prevent dust buildup, which can reduce light output and cause overheating. Follow these steps:

1. Unplug the product from power.
2. Allow the product to cool to room temperature.
3. Use a vacuum or dry compressed air with a soft brush to remove dust from external vents.
4. Clean transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply cleaning solution to a soft, lint-free cloth or lens tissue.
6. Wipe dirt and grime towards the outside of the surface.
7. Gently polish surfaces until clear and lint-free.
8. Always dry transparent surfaces thoroughly after cleaning.

[Note Symbol] Avoid using compressed air to spin cooling fans, as this can cause damage.

6. Technical Specifications

Dimensions and Weight

Note: Dimensions are rounded to the nearest decimal digit in inches.

Power

Power I/O

Light Source

Photometrics

Thermal

DMX

Ordering

Contact Us

Chauvet World Headquarters

Address: 3360 Davie Rd., Davie, FL 33314

Voice: (954) 577-4455 | Fax: (954) 929-5560 | Toll Free: (800) 762-1084

Email: chauvetcs@chauvetlighting.com | Website: www.chauvetprofessional.com

Technical Support

Voice: (844) 393-7575 | Fax: (954) 756-8015

Chauvet U.K.

Address: Pod 1 EVO Park, Little Oak Drive, Sherwood Park, Nottinghamshire, NG15 0EB, UK

Voice: +44 (0) 1773 511115 | Fax: +44 (0) 1773 511110

Email: UKtech@chauvetlighting.eu | Website: www.chauvetprofessional.eu

Chauvet Benelux

Address: Stokstraat 18, 9770 Kruishoutem, Belgium

Voice: +32 9 388 93 97

Email: BNLtech@chauvetlighting.eu | Website: www.chauvetprofessional.eu

Chauvet France

Address: 3, Rue Ampère, 91380 Chilly-Mazarin, France

Voice: +33 1 78 85 33 59

Email: FRtech@chauvetlighting.fr | Website: www.chauvetprofessional.eu

Chauvet Germany

Address: Bruno-Bürgel-Str. 11, 28759 Bremen, Germany

Voice: +49 421 62 60 20

Email: DEtech@chauvetlighting.de | Website: www.chauvetprofessional.eu

Chauvet Mexico

Address: Av. de las Partidas 34 - 3B (Entrance by Calle 2), Zona Industrial Lerma, Lerma, Edo. de México, CP 52000

Voice: +52 (728) 690-2010

Email: servicio@chauvet.com.mx | Website: www.chauvetprofessional.mx

Warranty & Returns

For warranty terms, conditions, and return information, please visit the Chauvet website:

• United States and Mexico: www.chauvetlighting.com/warranty-registration
• United Kingdom, Republic of Ireland, Belgium, Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration