Blackview Tab 70 WiFi

How to insert the TF card

Diagram showing the location of the TF card slot.

How to boot

Non-removable battery

Press the power button for 3-5 seconds to boot.

Language switching settings

• Main menu: Settings > System settings > Language and input method.
• Language and input method: Language > Add language.
• Select the language you need; the system will automatically jump back to the language interface.
• Select the icon after the language bar and drag it to the first position.

SAR (Specific Absorption Rate)

• The maximum electromagnetic radiation absorption ratio (SAR) of this product is ≤ 2.0 W/kg.
• In line with the requirements of the national standard GB 21288:2007.

Safety: In order to ensure safe use of the product, you must strictly abide by the following rules

• The pad should be at least 15 cm away from any medical implant or cardiac pacemaker and never put the device in your coat pocket.
• Do not expose the device and other batteries together with high temperatures or heat-generating equipment such as sunlight, heaters, microwave ovens, ovens or water heaters. Overheating of the battery can cause an explosion.
• When charging is complete or not charging, disconnect the charger from the device and unplug the charger from the power outlet.
• If the device is equipped with a non-removable battery, do not replace the battery yourself to avoid damaging the battery or device.
• Use of an unapproved or incompatible power source, charger or battery may cause fire, explosion or other hazards.
• Do not disassemble or reset the battery, insert other objects, connect to water or other liquids to avoid battery leakage, overheating, fire or explosion.
• Do not drop, crush, scratch or puncture the battery to avoid subjecting the battery to excessive external pressure, internal short circuit and overheating of the battery.
• The company does not bear responsibility for accidents caused by non-standard charging equipment.
• For full CE compliance information, please visit: www.blackview.hk/car

Maintenance

• To ensure safe and effective use and extend the service life of the pad as much as possible, please understand the maintenance of this pad.
• Please follow the instructions in the manual to open the pad, disassemble the accessories, and do not try other methods.
• Please avoid falling, knocking or shaking your pad. Rough handling of the pad can cause the screen to rupture, damaging the internal circuit board and delicate components.
• Do not use chemical solvents or detergents to clean your pad. Clean the pad with a soft cotton cloth dampened with water or a mild soap.
• Clean the lens (e.g., camera lens) and display with a clean, dry, soft cloth.
• If you encounter an abnormal image, such as a crack during use, the processing method is as follows: For a pad that cannot remove the battery, please press and hold the power button for more than 12 seconds; the pad will be forced to restart (unlock the pad when restarting). This can solve general bugs. For a pad that can remove the battery, please remove the battery, then insert the battery and restart it to solve the bug.
• When the charger is not in use, please unplug it from the power outlet. Do not connect the battery that has been fully charged to the charger for a long time, as overcharging will shorten the battery life.

Regulatory Information

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Warning

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne peut causer d'interférences ; et (2) Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.

The device for operation in the band 5150-5250 MHz is only for indoor use.

RF Exposure Information and Statement

The SAR limit of USA/Canada (FCC/IC) is 1.6 W/kg averaged over one gram of tissue. Device types: Tab 70 WiFi (FCC ID: 2A7DX-TAB70WF, IC: 25768-TAB70WF) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use the body is 0.168 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0 mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Le SAR limite pour les USA/Canada (FCC/IC) est de 1.6 W/kg moyen sur un seul gramme de tissu. La valeur maximale déclarée sous ce critère lors de la certification du produit pour l'utilisation du corps est de 0.168 W/kg. Opérations typiques avec la partie arrière de la manoeuvre gardée à 0 mm du corps, afin de maintenir la conformité avec les exigences du FCC relatives à l'exposition RF, L'utilisation des accessoires qui maintiennent une distance de séparation de 0 mm entre le corps de l'utilisateur et le dos de la main. L'utilisation des accessoires qui ne satisfont pas à ces exigences peut ne pas être conforme aux exigences du FCC relatives à l'exposition à la RF. Et devrait être évité.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0 mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Cet appareil a été testé pour un fonctionnement typique du corps sous pression, pour satisfaire aux exigences relatives à l'exposition RF, une distance minimale de séparation de 0 mm doit être maintenue entre le corps de l'utilisateur et la poignée. Y compris les antennes, les bandes de fréquences et les satellites, Des accessoires similaires utilisés par cet appareil ne doivent pas contenir de composants métalliques. Seule la fourniture ou une antenne agrée.